dead battery AUDI A3 2016 Owner´s Manual

..... N
0 > CX)
..... I.Cl U"I
..... I.Cl .....
.. The LED blinks several times when you press a
button longer (convenience opening*) .
.. If the LED does not blink, the remote control
key battery is dead. The message
1:1 Please
change key battery
may also appear in the in­
strument cluster display . Replace the battery .
Replacing the remote control key battery
.. Pry the cover @off of the key (Dusing a coin
c::>fig . 20 .
.,. Insert the new battery with the "+" facing up .
.. Press the cover back onto the key until it clicks
into place .
We recommend having the battery replaced by
an authorized Audi dealer or authorized Audi
Service Facility .
@ For the sake of the environment
Dead batteries must be disposed of using
methods that will not harm the env ironment.
Do not dispose of them in household trash .
@ Tips
The replacement battery must meet the same
specifications as the orig inal battery.
Remote control key synchronization
The remote control key must be synchronized if
the vehicle does not lock and unlock with the re­
mote control.
.. Press the remote control key button~-
.. Insert the key in the driver's door lock within 30
seconds .
.,. Press the~ button or~ button .
Open ing and closing
Unlocking/locking by remote control
Fig. 21 Remote control key or conve nien ce key : button pro­
gramm ing
@ m Open
@ i'.D Close
© .:::::$Unlock luggage compartment lid
@ IPANIC !T rigger the alarm
... To unloc k the vehicle, press the button@~
c::>fig. 21 .
.. To lock the vehicle, bring the selector lever into
the P position and press the~ button
@.
.. To unlock the luggage compartment lid, press
the ~ button © briefly.
.,. To open the luggage compartment lid, press
and hold the~ button © for at least one sec­
ond .
... To trigger the alarm, press the red I PANIC ! but­
ton @. T he veh icle horn and emergency flash­
ers turn on.
.. To turn off the alarm, press the red I PANIC !
button @again .
If the vehicle is unlocked and a door or the lug­
gage compartment lid are not opened w ithin 45
seconds, the vehicle locks again automat ically.
This feature prevents the vehicle from being acci ­
dentally left unlocked over a long period of time.
This does not apply if you press the~ button ©
button for at least one second.
For vehicles with
safety central locking (selective
unlocking)
c::> page 40, only the driver's door
and the fuel f iller door are opened by pressing
the ~ button @ once, and the entire vehicle un-
locks when the button is pressed twice .
Ill>
37

,....,
N
0 > co ,...., Selector lever emergency release
"' Press and hold the yellow re le a se button wi th
the screwdriver ~
fig. 87.
"' Press the release button in the se lector lever @
and move the leve r into the N position.
"' Clip the shift cove r back into the shift gate a fter
us ing the emergency release.
If t he vehicle m ust be pushed or towed due to a
power fai lure (fo r example, the battery is dead),
the selector lever must f irst be moved to the N
position using the emergency release mecha­
ni sm.
A WARNING
On Ly m ove the se lector lever ou t of the P posi ­
tion when the par king b rake is set.
If that
does not work, se cure the vehicle wi th the
bra ke ped al. Ot herw ise, the vehicle coul d
sta rt to move unintention ally whe n the sele c­
to r lever is moved out of the P pos ition .
Automatic transm ission
97

Emergency situations
electronic components, such as control
units, re lays, radio, etc.
- There must be no electrical contact between
the vehicles otherwise current could already
start to flow as soon as the positive(+) ter­ minals are connected.
@ Tips
The discharged battery must be properly con­
nected to the vehicle's electrical system .
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negat ive g ro und cable to the negative g round
post on the battery manager control unit.
Using jump start cables
Connect the jump start cables in the exact order
described below.
Fig. 228 Engine co mpartment : connectors for ju mp start
cables and a charger
Fig. 229 Jump starting the battery wit h another vehicle:
@ -drained battery, @- starter battery
Plug-in hybrid drive* : the connection points for
the jump start cables vary<=>
page 108.
296
00 ~
5 > 00 ID
The battery is located to the left in the engine
compartment.
Do not jump start a frozen or
thawed battery
¢ A in Starting with jumper ca­
bles on page 295 !
Replace the battery. The pro­
cedure for connecting jump start cables that is
described next is designed to help jump start
your vehicle.
Vehicle with drained battery :
.,. Read the following carefu lly <=> page 295
.,. Set the parking brake and place the selector
lever in the P position.
.,. Turn the ignition and electr ical equipment off
in both vehicles .
Connecting the negative terminal(-) to the
negative terminal(·) (black)
.,. To reach the battery terminals, flip the battery
cover cap to the side¢
fig. 228 .
1. Clamp the end of the red jump start cab le to
the terminal @¢
fig. 229 on the dead bat­
te ry @ ¢
0 in Starting with jumper cables
on page 295.
2. Clamp the other end of the red jump start ca­
ble to the terminal @on the charging bat­
tery @.
Connect NEGATIVE(-) to NEGATIVE(-)
(black)
3. Clamp the black end of the jump start cable
preferably at the ground point, or on the
negative terminal @ on the charging battery
®·
4. Clamp the other end of the black jump start
cable
only to the ground point © on your
vehicle @
¢0.
5. Route the jump start cables so they cannot
get caught in the moving parts in the engine
compartment.
Starting the engine
6 . Start the engine in the vehicle giving the
charge and let it run at idle.
7. Start the engi ne in the vehicle with the dead
batte ry and wait two to three minutes until it
"runs smoothly".
8. If the engine does not start, stop the starting
procedure after 10 seconds and then repeat
it after approximately 30 seconds. ..,_