wheel bolt torque AUDI A3 CABRIOLET 2015 Owners Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: A3 CABRIOLET, Model: AUDI A3 CABRIOLET 2015Pages: 302, PDF Size: 73.83 MB
Page 258 of 302
256 Tires and wheels
loss of control, crashes and serious per
sona l injuries . Have worn or damaged tires
replaced immediate ly.
- Winter tires have maximum speed rating
that may be lower than your vehicle's
maximum speed .
- Never drive faster than the speed for
which the winter or other tires installed
on your vehicle are rated.
A WARNING
Always adjust your driving to the road and
traffic conditions. Never let the good ac
celeration of the winter tires and all-wheel
drive tempt you into taking extra risks. Al
ways remember:
- When braking, an all-wheel drive vehicle
handles in the same way as a front drive
vehicle .
- Drive carefully and reduce your speed on
icy and slippery roads, even winter tires
cannot help under black ice conditions.
@) For the sake of the environment
Use summer tires when weather condi
tions permit. They are quieter, do not wear
as quickly and reduce fuel consumption.
Snow chains
Snow chains may be fitted only to the front
wheels, and only to certain tire sizes. Ask your
authorized Audi dealer on which tire sizes
snow chains can be used.
If you are going to use snow chains, then you
must install them on the front wheels at
l east.
The snow chains must have low-profile links
and must not be thicker than 0.53 inch
(13.5 mm), including the lock.
Remove wheel center covers and trim discs
before putting snow chains on your vehicle
q 0 . For safety reasons cover caps must then
be fitted over the wheel bolts. These are avail
able from authorized Audi dealers.
A WARNING
Using the wrong snow chains for your vehi
cle or installing them incorrectly can in
crease the risk of loss of control leading to
serious personal injury.
- Snow chains are available in different
sizes . Always make sure to follow the in
structions provided by the snow chain
manufacturer.
- When driving with snow chains never
drive faster than the speed permitted for
your specific snow chains.
- Always observe local regulations.
@ Note
-Remove snow chains before driving on
roads not covered with snow to avoid
damaging tires and wearing the snow
chains down unnecessarily .
- Snow chains, which come into direct con
tact with the wheel rim, can scratch or
damage it. Therefore, make sure that the
snow chains are suitably covered. Check
the position of the snow chains after
driving a few yards and correct if neces
sary. Follow the instructions from the
snow chain manufacturer when doing so.
@ Tips
Where snow chains are mandatory on cer
tain roads, this normally also applies to
vehicles with all-wheel drive .
Wheel bolts
Wheel bolts must always be tightened to the
correct torque.
The design of wheel bolts is matched to the
factory installed rims. If different rims are fit
ted, the correct wheel bolts with the right
length and correct ly shaped bolt heads must
be used. This ensures that wheels are fitted
securely and that the brake system functions
correctly . .,..
Page 259 of 302
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
In certain circumstances, you may not use
wheel bo lts from a different vehicle -
even if it
i s the same mode l
Qpage 284.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose caus ing loss of
control, a collision and ser ious personal in
jury .
- Always keep the wheel bolts and the
threads in the wheel hubs clean so the
wheel bolts can turn easily and be prop
erly t ightened.
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose w hile d riving if greased or
o iled,
even if tightened to the spec ified
torq ue.
- Only use wheel bo lts that belong to the
rim being ins talled.
- Never use different whee ls bolts on your
vehicle .
- Always maintain the correct tightening
torque fo r the wheel bolts to reduce the
risk of a wheel loss. If the tigh teni ng tor
que of the wheel bolts is too low, they
can loosen and come out when the vehi
cle is moving . If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel ca n be
come loose .
(D Note
The specified torque for the wheel bo lts is
90 ft lb (120 Nm) w ith a tolerance of
± 7,4 ft lb(± 10 Nm). Torque whee l bolts
diagonally. After changing a wheel, the
torque must be checked as soon as possi
b le with a torque wrench -prefe rably by an
author ized Audi dealer or qualified wo rk
shop.
Low aspect ratio tires
Your Audi is factory-equipped with low aspect
ratio tires . These tires have been thorough ly
tested and been selected spec ifically for your
model for the ir superb performance, road feel
Tire s an d wheel s 257
and handling under a variety o f driving condi
tions. Ask your authorized A udi dealer for
more details .
T he low aspec t ratio of these tires is ind icate d
by a numera l of
55 or le ss in the tire's size
designation. The numera l represents the ratio
of the t ire's sidewa ll height in relation to its
tread width expressed in percentage.
Conven
tiona l tires have a he ight/w idth rat io of 60 or
more .
The performance of low-a spect-ratio tire s is
particularl y sens it iv e to improper inflation
pressure. It is therefore important that low
a spect ratio tir es are inflated to the specified
pre ssure and that the inflation pr essure i s
regularly checked and ma intain ed . Tire pr es
s ure s should be checked at lea st on ce a
month and alway s bef ore a long trip
~ page 240 , Checking tire pressure .
A Word about Low Aspect Ratio and High
Performance Ti res
Hig h pe rformance tires are des igned for bet
ter performance and handling in warm cli
mates. When driving in cold, snowy or icy
weather, you sho uld equ ip your vehicle w it h
four all-season or winter tires, which
offer
better traction under those condit ions. We
suggest you use the Audi recommended win
te r or a ll-season tires specified for you r Audi.
High performance tires a lso have a lower as
pect ratio that aids performance and han
dling . Driving over rough or damaged road
surfaces, as well as debr is, cu rbs and other
obstacles can cause serious damage to
whee ls, tires, vehicle body, and suspens ion
parts . B e carefu l to avo id road hazards and re
du ce your speed , espec ia lly if your vehicle is
equipped wi th low prof ile tires .
Please a lso remember when making your se
lection that, wh ile these tires deliver respon
s ive handling, t hey m ay ride less comfo rtably
and make more noise than o thers . Finally,
these tires may wear more quickly than other
c h oices.
IJJ>
•
•
•
Page 266 of 302
264 What do I do now?
-Always store the vehicle tool kit, the jack
and the replaced tir e in the luggage com
partment ¢
page 132.
Changing a wheel
When you change o wheel, follow these
quence described below step-by-step and in
exactly that order .
1. Remove the decorative wheel cover*. For
more details see also¢
page 264, Deco
rative wheel covers
or ¢ page 265,
Wheels with wheel bolt caps.
2 . Loosen the wheel bolts¢ page 265 .
3. Locate the proper mount ing point for the
jack and align the jack below that point
¢page 266.
4. Raise the car with the jack ¢ page 266.
5. Remove the
wheel with the flat tire and
then install
the spare ¢ page 267.
6. Tighten all wheel bolts lightly.
7 .
Lowe r the vehicle with the jack.
8 . Use the wheel bolt wrench and
firmly
tighten all whee l bolts c::> page 265.
9. Replace the decorative wheel cover*.
A WARNING
Always read and follow all WARNINGS and
information
c::> .&. in Raising the vehicle on
page
266 and c::> page 268.
After changing a wheel
A wheel change is not complete without the
doing the following .
• Always store the vehicle tool kit, the jack*
and the replaced tir e in the luggage com
partment ~
page 132 .
• Check the tire pressure on the spare wheel
i mmediately after mount ing it.
• As soon as possible, have the
tightening
torques
on a ll wheel bo lts checked with a
torque wrench. The correct tightening tor
que is 90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as poss i
ble.
(D Tips
- If you notice that the wheel bolts a re
corroded and difficult to turn while
chang ing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
- After changing a whee l, the tire pressure
in all four tires must be checked/correct
ed and the tire pressure monitoring indi
cator must be stored in the MMI
c::>page260.
Decorative wheel covers
Applies to vehicles: wit h decorative whee l covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 183 Chang ing a wheel : Remov ing th e w heel cover
Removing
.,. Insert the hook (provided with the vehicle
tool kit) in the hole in the whee l hub cover .
.,. Pull
off the decorative wheel cover
c::>fig.183.
Page 270 of 302
268 What do I do no w?
-Pull the reversible blade from the screw
driver before you use the hexagonal
socket in the handle to t urn the whee l
bo lts.
- When mounting tires with
unid ire ctional
t re ad design
make s ure the tread pat
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to turn. Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the hub. Remove all dirt from these
surfaces before remount ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern
int ended fo r use in a specific dir ection
When us ing a spare tire w ith a tread pattern
i ntended for use in a specific direction, please
note t he following:
- The direction of rotation is marked by an ar
row on the side of the tire .
-If the spare t ire has to be installed in the in
correct direction, use the spare tire only
temporarily since the t ire will not be able to
achieve its optimum perfo rma nce character
ist ics with rega rd to aquaplaning, noise and
wea r.
- We recommend that you pay particular at
tent ion to this fact du ring wet weat her and
that you adjust your speed to match road
condit ions .
- Replace the fla t tire w ith a new one and
have it ins talled on your veh icle as soon as
possible to restore the handling advantages
of a unidirectiona l tire .
Notes on wheel changing
Please read the information ¢ page 248, New
tires and replacing tires and wheels
i f you are
go ing to use a spare t ire which is d ifferent
from the tires on your veh icle . After you change a tire:
-
Ch eck the tire pr essure on th e spar e imm e
diatel y after in stallation .
- Hav e th e whe el bolt tight ening torque
c h ec ked with a torque wr ench as soon as
po ssible by your author ized Audi de aler or
a qu alified servic e sta tion.
- With ste el and alloy wheel r im s, the wheel
bolt s ar e c orre ctl y tightened at a torque of
9 0 ft lb (120 Nm ).
- If you notice th at the wheel b olt s ar e co r
rod ed and diffi cult to turn w hile changing
a tire , the y should be repl aced before you
check the t ightening to rque.
- Repl ace the flat tire with a new o ne and
ha ve it in stalled on your vehicle as soon a s
possible. Remount the wheel cov er.
Until then , dri ve with extra care and at re
duc ed sp eed s.
A WARNING
-
- If you are going to equip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information
¢ page 248,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com
pa rtment and are not loose in the pas
senger compartment.
- In an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.
- Always sto re damaged wheel , jack and
too ls se curely in the luggage compart
men t. Otherwise, in an accident or s ud
den maneuve r they could f ly forwa rd,
causing injury to passengers in the vehi
cle.