AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual A4 1998 B5 / 1.G AUDI AUDI https://www.carmanualsonline.info/img/6/1234/w960_1234-0.png AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual
Trending: wheel alignment, ECU

Page 1 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-77
 
     
Drive flange/driveshaft radial 
deviation, measuring and 
identifying 
     
Special tools and equipment 
     
VW38 universal measurement bracket 
     2024A engine sling
     Dial indi

Page 2 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual      
The radial deviation can also be measured with 
final drive installed, by separating driveshaft at 
final drive. Notes   Page 39
-68
 . 
Pa
ge 2 of 8 Drive flan
ge/driveshaft radial deviation, m

Page 3 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-78
      
-  Remove front left bolt at crossmember for final 
drive. 
    
-  Remove strap from 2024A engine sling and tighten with bolt -2- (M10 x 
85 mm) at open bore. Position strap using approx

Page 4 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-79
      
Driveshaft, adjusting
 
     
Special tools and equipment 
     
3298 alignment fixture for all wheel drive 
driveshaft 
     3139/2 spacer 
     
- Observe all cautions   Page 39
-68

Page 5 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-80
 
    
-  Place two 3139/2 spacers in 3298 assembly tool.
    
Note:  
Never install alignment fixture onto balance plates.  -  Mount 3298 assembly tool with two 3139/2 spacers and tighten plast

Page 6 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-81
      
-  Remove mounting bolts and shims of center 
bearing. 
    
The following shims are available   -  Align center driveshaft bearing so that dimensions -a- are same on 
both sides. 
- Meas

Page 7 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-82
      
Aligning driveshaft longitudinally  
    
The center bearing must be aligned centrally between markings -A- and -
B-.  -  Push driveshaft with alignment fixture toward rear as far as poss

Page 8 of 8

AUDI A4 1998 B5 / 1.G 01A Transmission Final Drive Flange Driveshaft Workshop Manual 39-83
       Installation is the reverse of removal, note the 
following:  
     
-  Align exhaust system free of stress.
       Repair Manual, Engine Mechanical, Repair 
Group 26       
Tightening to
Trending: ECU, wheel alignment