wiring AUDI A4 1998 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Manual PDF

01-144

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1613 / 18021
MIL Call-up Circ.Open
Short to B+ Wiring connection between Engine
Control Module (ECM) -J192- and
Transmission Control Module (TCM) -J217-
faulty

- Check MIL wiring from Transmission
Control Module (TCM) -J217- page 24
-
105


Malfunction cause found: Yes
No

- Erase DTC memory, test drive, after test
drive check DTC memory again
MIL Status:
MIL lights up
immediately
Transmission Control Module (TCM) -
J217- faulty

Repair Manual, 5 Spd.
Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01
- Replace ABS control module -J104-

Malfunction cause found: Yes
No

- Erase DTC memory, take test drive, after
test drive check DTC memory again
For troubleshooting
Display group 027
Engine Control Module (ECM) -J192-
faulty

- Replace and code ECM -J192- page 01
-265
erase DTC memory and take
test drive check DTC memory
Notes:

This malfunction can only occur in connection with an automatic transmission.
Pa
ge 196 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-166
Test table display group 001 Display
field Display on
VAG 1551 scan
tool Malfunction cause
Malfunction repair
1 Greater than
110
or
Less than 85
Engine Coolant Temperature (ECT)
sensor -G62-
Wiring connection to Engine Control
Module (ECM) -J192-
Coolant thermostat faulty
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 19
- Check DTC memory page 01
-13
- Check -G62- page 28
-25
- Check engine coolant thermostat
2 Less than 1.450
V
Large intake air leak between intake
manifold and Mass Air Flow (MAF)
sensor Repair cause
Greater than
1.580 V Electrical consumers on, steering wheel
at end stop, driving mode selected
(automatic transmission)
Tolerance for new engines: - Switch consumers off
- Center steering wheel
- Put selector lever in P or N position
display group 004, display field 4
Max. 1.660 V
When engine speed increases, the display
value increases to 2.500 V, falls to 0.000 V
Pa
ge 231 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-169

Display
field Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
3 Outside tolerance
range
Closed Throttle Position (CTP)
switch activated or faulty CTP switch or throttle position
sensor -G69- incorrectly adjusted Electrical consumers onSteering wheel at end stopDriving mode selected (automatic
transmission) Moisture in connector for -G69-Ground point on intake manifold - Check DTC memory page 01
-13
- Check and adjust -G69- page 24
-77
- Switch electrical consumers off
- Center steering wheel
- Selector lever in P or N display group 004,
display field 4 - Visual inspection
- Check ground connection according to wiring
diagram
4 0 or 1
Closed Throttle Position (CTP)
switch -F60- faulty Throttle position sensor -G69-
incorrectly adjusted Throttle sticks Floor mat presses against
accelerator pedal Moisture in connector of -G69-Accelerator pedal cable adjustment Display group 011, display field 4
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 20
- Check DTC memory page 01
-13
- Check and adjust -F60- page 24
-73
- Visual inspection
- Adjust accelerator pedal cable:
Pa
ge 235 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-172

Display
field Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
3 Greater than 0%
at idle
Throttle position sensor -G69- faultyAccelerator pedal cable adjustmentThrottle sticks
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 20
- Check DTC memory page 01
-13
and/or
display group 002
- Adjust accelerator pedal cable:- Repair cause
At wide open
throttle less than
95%
Throttle position sensor -G69- faultyAccelerator pedal cable adjustment Throttle position sensor -G69- incorrectly
adjusted
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 20
- Check DTC memory page 01
-13
and/or
display group 002
- Adjust accelerator pedal cable:- Check and adjust sensor -G69- Repair
Group 24
4 No display
Wiring connection between instrument
panel insert and Engine Control Module
(ECM) -J192- faulty Open circuit or short between Vehicle
Speed Sensor (VSS) -G68- and -J192- - Electrical Wiring Diagrams, - Check vehicle speed signal page 24
-97
- Check -G68- check vehicle speed
sensor:
Pa
ge 240 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

G68- faulty Troubleshooting & Component Locations
Note on display field 4:
If no vehicle speed is shown on VAG 1551 scan tool, first make sure the vehicle speed display is OK. If vehicle speed display
is faulty, check vehicle speed sensor:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
Pa
ge 241 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-191

Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
3/4 Display does not fluctuate-constant
between 0.0 - 0.3 V and/or between
0.6 - 0.9 V
Fuel injector faulty- Check fuel injectors page 24
-29

Spark plug faultyLarge intake air leak Engine Coolant Temperature
(ECT) sensor -G62- faulty EVAP canister purge
regulator valve -N80- - Check spark plug
- Repair cause
- Check DTC memory page 01
-13

and/or check -G62-
- Check using output diagnostic test
mode page 01
-145
and/or check -
N80-

Heated Oxygen Sensor
(HO2S) -G39- faulty or dirty Oxygen Sensor (O2S) heater
-Z19- does not function - Check DTC memory page 01
-13

and/or check -G39-
- Check -Z19- page 24
-49

Fuel system pressure too
high or too low - Check fuel pressure regulator and
residual pressure page 24
-20


Constant 2.550 V Short to positive (B+) through:
Heated Oxygen Sensor
(HO2S) -G39- wiring Engine Control Module
(ECM) -J192- - Check -G39- page 24
-49Pa
ge 267 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-192

Display
fields Display on VAG 1551 scan tool
Malfunction cause
Malfunction repair
3/4
Constant value between 0.350 -
0.450 V Open circuit in:
Heated Oxygen Sensor (HO2S) -G39-
wiring Engine Control Module (ECM) -J192-- Check -G39- page
24
-49


Constant 0.000 V Short to ground in:
Heated Oxygen Sensor (HO2S) -G39-
wiring Engine Control Module (ECM) -J192-- Check -G39- page
24
-49


Notes on display field 4:
The display value at times must drop below 0.3 V
and exceed 0.6 V. Display values less than 0.40
V indicate lean condition; greater than 0.40 V
indicate rich condition.

HO2S voltage U (mV) vs. Lambda ( ) A - HO2S voltage (mV) high
Rich mixture (fuel excess or lack of air)
High CO value
B - Oxygen sensor probes voltage (mV) low
Pa
ge 269 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-198
Display groups 015 and 016
Notes on display fields 2, 3 and 4:
If there is a difference of more than a factor of 3 between the lowest and the highest knock sensor signal in one display group,
the following malfunction is possible:

Corrosion on the harness connector
If there are differences of more than 50% in knock sensor signal between display group 015 (cylinders 1 to 3) and display
group 016 (cylinders 4 to 6), the following malfunctions are possible:
Corrosion on the harness connector
Open circuit
Knock sensor faulty
If no malfunctions are found during the electrical testing of the knock sensor, the wiring and the connections, the engine
should be checked for loose subassemblies or engine damage (e.g. oil burning due to faulty piston) Display groups 013
and/or 014.
Pa
ge 279 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-255

Test box VAG 1598/19, connecting


CAUTION!

Wait at least 30 seconds after the ignition has
been switched off before disconnecting the
ECM harness connector.

Note:
By disconnecting the ECM, the permanent
voltage supply is disconnected and therefore the
learning values, DTC memory and readiness
code are erased.

- Switch ignition off.

- Remove ECM.

Note:
Terminal assignments of the connectors A, B, C, D and E are identical to
the socket assignments of the test box. - Connect test box VAG 1598/19 to wiring harness.
Pa
ge 354 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1