display AUDI A6 1995 C5 / 2.G ATW Engine Electronic Power Control Checking Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1995, Model line: A6, Model: AUDI A6 1995 C5 / 2.GPages: 51, PDF Size: 0.3 MB
Page 13 of 51
24-121
Throttle valve control module, adapting
The adaptation teaches the Engine Control
Module (ECM) various positions of the throttle
valve when the ignition is on and the engine is
stopped. These positions are stored in the
control module The return communication
regarding the position of the throttle valve occurs
via the two angle sensors for throttle drive.
An adaptation must always be performed when
the throttle valve control module -J338- or the
Engine Control Module (ECM) are removed and
installed (or replaced) or if voltage supply to the
Engine Control Module (ECM) is interrupted.
The learning process (adaptation) occurs:
automatically if the ignition is switched on for at
least 10 seconds without operating starter and
accelerator pedal and the Engine Control
Module (ECM) recognizes "adaptation
required". (There will be no notification of
whether adaptation was successful or not
however). Adaptation required is recognized if
stored voltage values from the angle sensors
do not match actual measured voltage values
within a certain tolerance range.
via initiation of basic setting (function 04)
display group 060 with ignition on.
Pa
ge 13 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 15 of 51
24-123
Procedure
- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Ignition
must remain switched on.
Rapid data transfer
HELP
Select function XX
When indicated on display
- Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
button to confirm input.
Basic Settin
g
Q
Enter displa
y group number XXX
When indicated on display
After pressing Q-button, throttle valve actuator will be switched on without
current.
In this condition, the throttle valve will be drawn into an emergency
position by a mechanical spring, which is located in the throttle valve
control module. The values supplied by the two angle sensors in this
emergency position are stored by the Engine Control Module (ECM). - Press buttons -0-, -6- and -0- to select "display group number 060" and
press -Q- button to confirm input.
Pa
ge 15 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 16 of 51
24-124
Next, the throttle valve is opened by a certain
value. If this value is reached, the throttle valve
actuator is once again de-energized. Now, the
mechanical spring must close the throttle valve to
the previously learned emergency position within
a specified time (spring test).
Then, the throttle valve is closed by the throttle
valve actuator; the values supplied by the angle
sensors in the throttle valve control unit are
stored by the Engine Control Module (ECM).
If Engine Control Module (ECM) should de-
energize throttle valve actuator during driving
operation, this is expressed by an increased,
surging idle speed (RPM). The engine accepts
gas only after great delay. System in basic setting 60
1
2
3
4
When indicated on display
- Check specified values for throttle valve control module in display fields
3 and 4.
Pa
ge 16 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 17 of 51
24-125
Display fields
1 2 3 4
Display group 060: Adaptation of throttle valve control module
Display xx % xx %
x
---
Indicated Throttle
valve angle
(angle
sensor 1) Throttle
valve angle
(angle
sensor 2) Adaptation step counter
Adaptation condition
Functional
range
0 to 8
ADP in progress
ADP OK
ERROR
Specified
value 3 to 93 % 97 to 3 %
8
ADP OK
Note
After adaptation, the adaptation step
counter reaches the number 8 (it is OK for
numbers to be skipped). If "ERROR." is displayed:
Check DTC memory Page
01
-16
.
If specified value is not
obtained: Note, Page 24
-
126
Note:
The abbreviation "ADP" in display field 4 stands for "Adaptation".
Pa
ge 17 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 18 of 51
24-126
Note:
The control module can abort adaptation for the
following reasons:
Throttle valve cannot be closed completely (e.g.
contamination).
Battery voltage is too low.
Throttle valve control module or wire connection
is faulty.
Engine is started during adaptation or
accelerator pedal is operated.
Tension of throttle valve housing (check
bolts).
After termination, tester displays "Function is
unknown or cannot be performed at the
moment". The next time the ignition is switched
on (several seconds), adaptation will be
automatically repeated.
- End basic adjustment of the engine by pressing
the key.
Rapid data transfer
HELP
Indicated on display (function selection):
Pa
ge 18 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 21 of 51
24-128
Angle sensor 1 for throttle drive (power
accelerator actuation) -G187- and angle sensor 1
for throttle drive (power accelerator actuation) -
G188- inform the Engine Control Module (ECM)
about the position of the throttle valve. Both
angle sensors are located in the throttle valve
control module.
Test sequence
- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Ignition
must remain switched on.
Rapid data transfer
HELP
Select function XX
When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read measuring value block
Q
Enter displa
y group number XXX
When indicated on display
- Press buttons -0-, -6- and -2- to select "display group number 062" and
press -Q- button to confirm input.
Read Measuring Value Block 62
1
2
3
4
Indicated on display
- Check specified values for E-gas potentiometer voltages in display
fields 1 and 2.
Pa
ge 21 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 22 of 51
24-129
Display fields
1 2 3 4
Display group 062: E-Gas potentiometer voltages
Display
xx %
xx % xx % xx %
Indicated
Throttle valve angle
(angle sensor 1) Throttle valve angle
(angle sensor 2) Sensor 1 for
Pedal position Sensor 2 for
Pedal position
Specified value
3 to 93 %
97 to 3 % 12 to 97 % 4 to 49 %
Note:
Engine Control Module (ECM) calculates the
voltage values of the angle sensors in percent
relative to 5 volts and displays these percentage
values. (5 volts supply voltage represents 100
%).
- Observe display field 1 and 2.
- Slowly depress accelerator pedal completely.
Percent indication in display field 1 must rise
uniformly. In the process, the tolerance range of
3 to 93% is not completely utilized.
Percent indication in display field 2 must
decrease uniformly. The tolerance range 97 to 3
% is not used completely during this.
Pa
ge 22 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 23 of 51
24-130
Note:
The reason why the value indicated in display
field 1 climbs, while the value indicated in
display field 2 decreases, has to do with the fact
that the potentiometers (angle sensors) in the
throttle valve control unit run in opposite
directions.
This means that the voltage tap of angle sensor
1 runs from 0 to 5 volts. (The more the throttle
valve is opened, the larger the voltage; percent
indication climbs).
The voltage tap of angle sensor 2 runs from 5
to 0 volts. (The more the throttle valve is
opened, the lower the voltage; the percentage
decreases).
If indications do not resemble description:
- Check voltage supply and wire connections of
throttle valve control module Page 24
-131
.
Pay particular attention to harness connectors
that could be loose or corroded.
- Check accelerator pedal position sensor Page
24
-133
.
Pa
ge 23 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 27 of 51
24-134
Both the Throttle Position (TP) sensor -G79- and
the Sender -2- for accelerator pedal position -
G185- are located at the accelerator pedal and
communicate the driver's intentions to the ECM
completely independently of each other. Both
sensors are stored in one housing.
Test sequence
- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Ignition
must remain switched on.
Rapid data transfer
HELP
Select function XX
When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read measurin
g value block
Q
Enter display group number XXX
When indicated on display
- Press buttons -0-, -6- and -2- to select "display group number 062" and
press -Q- button to confirm input.
Read Measuring Value Block 62
1
2
3
4
Indicated on display
- Check specified values for E-gas potentiometer voltages in display
fields 3 and 4.
Pa
ge 27 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4
Page 28 of 51
24-135
Display fields
1 2 3 4
Display group 062: E-Gas potentiometer voltages
Display xx % xx %
xx %
xx %
Indicated Throttle valve angle
(angle sensor 1) Throttle valve angle
(angle sensor 2) Sensor 1 for
Pedal position Sensor 2 for
Pedal position
Specified value 3 to 93 % 97 to 3 %
12 to 97 %
4 to 49 %
Note:
Engine Control Module (ECM) calculates the
voltage values of the angle sensors in percent
relative to 5 volts and displays these percentage
values. (5 volts supply voltage represents 100
%).
- Observe display field 3 and 4.
- Slowly depress accelerator pedal completely.
Percent indication in display field 3 must rise
uniformly. The tolerance range 12 to 97% is not
used completely during this.
Percent indication in display field 4 must also rise
uniformly. In the process, the tolerance range of
4 to 49% is not completely utilized.
Pa
ge 28 of 51 Electronic En
gine Power Control
(EPC
) (E-Gas
), checkin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.4