check engine AUDI A8 1996 D2 / 1.G 01V Transmission Remove And Install Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A8, Model: AUDI A8 1996 D2 / 1.GPages: 64, PDF Size: 1.44 MB
Page 16 of 64
37-86
For 6 cylinder TDI engines
Note:
Illustration depicts engine from rear with the transmission removed.
Continuation for all vehicles - Loosen bolt -A- (at rear of turbocharger) several turns and rotate brace
-B- to side in arrow direction. Then re-tighten bolt -A- lightly.
If this is not the case, an axle alignment must be performed after the
carrier is installed. - Before loosening subframe, it must be checked whether holes -1- and -
2- (at least) line up using 3393 testing mandrel.
Pa
ge 16 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 19 of 64
37-89
Installing
Installation is reverse of removal, noting the
following:
Before installing:
All-wheel-drive vehicles
- Clean threads in driveshaft flange!
Continuation for all vehicles
- Clean ATF lines page 37
-158
.
- Insert torque converter into transmission page
32
-8 .
WARNING!
Check installation dimension of torque
converter before installing transmission
page 32
-8
- Make sure bushings are correctly seated.
Note:
If the bushings get stuck in the transmission
housing, they must be removed and new
bushings must be installed on the engine.
Pa
ge 19 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 23 of 64
37-93
Note:
If installed, place intermediate plate onto
bushings.
Make sure that wires do not get pinched as
transmission is docked at engine.
Check whether the torque converter is still
properly installed and has not slid out of the
converter housing toward the font:
- It must be possible to easily turn torque
converter by hand without much force.
WARNING!
In case of an incorrectly inserted torque
converter, the coupling plate of the torque
converter or the ATF-pump will be destroyed,
if the transmission is flanged to the engine.
- If the torque converter is difficult to move, check
installation dimension once again page 32
-8 .
Pa
ge 23 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 24 of 64
37-94
For 6 cylinder TDI engines
Continuation for all vehicles
Note:
Some bolts also have a bracket or a Ground (GND) connection attached
refer to tightening torque tables starting page 37
-119
onward. - Check whether brace -B- is still swung to side (arrow direction) before
installing the transmission.
- Install connecting bolts for engine/transmission.
Repair Manual, Engine Mechanical, Repair Group 26; removing and
installing exhaust system.
Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Install multi-function Transmission Range (TR) switch -F125-.
- Slightly raise engine/transmission subframe at rear via VAG1383A
hoist.
- Install remaining connecting bolts for engine/transmission.
- Install front exhaust pipes:
- Install subframe, observe tightening sequence and alignment with
master hole.
Pa
ge 24 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 37 of 64
37-107
Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version.
WARNING!
When working on the subframe, all precautions and notes which are
listed in Repair Manual, Suspension, Wheels, Steering must be
must be observed. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.
Repair Manual, Suspension, Wheels, Steering, Repair Group 40;
Subframe, removing and installing
- Before loosening carrier, special tool 3393 must be used to check
whether holes -1- and -2- line up.
- Completely lower subframe at rear and front.
Pa
ge 37 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 45 of 64
37-115
Note: - Press the lever/shift rod -2- at transmission completely toward rear
(toward right in illustration) until park lock is engaged.
- Shift selector lever into "P" and carefully press up ball head of selector
lever cable on lever/shift rod -2- using a pair of pliers.
Do not deform lever/shift rod when pressing up or else shifting cannot be
precisely adjusted any more.
Note:
Check whether the torque converter is still properly installed and has not
slid out of the converter housing toward the font:
Place intermediate plate onto bushings.Make sure that wires do not get pinched as transmission is docked at
engine.
- It must be possible to easily turn torque converter by hand without
much force.
Pa
ge 45 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2
Page 46 of 64
37-116
WARNING!
In case of an incorrectly inserted torque
converter, the coupling plate of the torque
converter or the ATF-pump will be destroyed,
if the transmission is flanged to the engine.
- If the torque converter is difficult to move, check
installation dimension once again page 32
-8 .
- Install connecting bolts for
engine/transmission.
Note:
Some bolts also have a bracket or a Ground
(GND) connection attached refer to tightening
torque tables starting page 37
-119
onward.
Pa
ge 46 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2