tow AUDI A8 1998 D2 / 1.G 01V Transmission Remove And Install Workshop Manual

37-83

Continuation for all vehicles

Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.

Automatic Transmission 01V with All Wheel Drive is supported at the
same positions as the Front Wheel Drive version. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
- Align adjustment plate parallel to transmission.
- Secure transmission on 3282 transmission support using bolt -A-.
- Remove left and right transmission support with transmission mount
page 37
-125

Pa
ge 13 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-91


For 6 cylinder TDI engines
Item A = bushings

Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.
Pa
ge 21 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-92

- Place transmission onto transmission support.

- Secure transmission on 3282 transmission support using bolt -A-.
- Move transmission into position between the lowered subframe and
vehicle floor.

Note:
Do not deform lever/shift rod when pressing up or else shifting cannot be
precisely adjusted any more. - Press the lever/shift rod -2- at transmission completely toward rear
(toward right in illustration) until park lock is engaged.
- Shift selector lever into "P" and carefully press up ball head of selector
lever cable on lever/shift rod -2- using a pair of pliers.
- If installed, press securing brace (arrow) open at end of selector lever
cable.
- Align transmission properly to engine.
Pa
ge 22 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-93

Note:

If installed, place intermediate plate onto
bushings.
Make sure that wires do not get pinched as
transmission is docked at engine.
Check whether the torque converter is still
properly installed and has not slid out of the
converter housing toward the font:

- It must be possible to easily turn torque
converter by hand without much force.

WARNING!

In case of an incorrectly inserted torque
converter, the coupling plate of the torque
converter or the ATF-pump will be destroyed,
if the transmission is flanged to the engine.

- If the torque converter is difficult to move, check
installation dimension once again page 32
-8 .
Pa
ge 23 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-106

- Loosen left and right transmission mounts from
subframe page 37
-125


Note:
When installing, make sure that locating sleeves -2- engage again. - Mark installation positions for threaded assemblies -1- and positioning
sleeves -2-.
- Remove nuts -1- on left and right engine mounts.

Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.
Pa
ge 36 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-114


Use 3282/19 adjustment plate to position the 3282 transmission support
for Automatic Transmission 01V.
The symbols on the adjustment plate indicate the necessary mounts and
the arrow points toward front of vehicle. - Position 3282 transmission support.
- Place transmission onto transmission support.

During this, the subframe is lowered approx. 150 mm at rear page 37
-
88
, illustration A37-0067. - Secure transmission on 3282 transmission support using bolt -A-.
- Move transmission into position between the lowered subframe and
vehicle floor.
- Align transmission properly to engine.
Pa
ge 44 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-115


Note: - Press the lever/shift rod -2- at transmission completely toward rear
(toward right in illustration) until park lock is engaged.
- Shift selector lever into "P" and carefully press up ball head of selector
lever cable on lever/shift rod -2- using a pair of pliers.

Do not deform lever/shift rod when pressing up or else shifting cannot be
precisely adjusted any more.
Note:
Check whether the torque converter is still properly installed and has not
slid out of the converter housing toward the font:
Place intermediate plate onto bushings.Make sure that wires do not get pinched as transmission is docked at
engine.
- It must be possible to easily turn torque converter by hand without
much force.
Pa
ge 45 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2

37-126

Removing

Note:
Transmission must be supported as indicated
when both transmission supports are removed.
Transmission does not need to be supported this
way when only one of the transmission supports
is being removed.

Note:
The symbols on the adjustment plate indicate the necessary mounts for
Automatic Transmission 01V and the arrow points toward front of vehicle. - Prepare 3282 transmission support for Automatic Transmission 01V
with3282/10 adjustment plate and place it on the VAG1383A
engine/transmission hoist.

Note:
If 3282 transmission support is not available, transmission can be
supported using the VAG1383A transmission lift and the 1359/2 universal
mount. - Roll VAG1383A engine/transmission hoist with 3282 transmission
support under transmission and support transmission.
Pa
ge 58 of 64 Transmission, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.2