brake light BUICK CENTURY 2004 Get To Know Guide
[x] Cancel search | Manufacturer: BUICK, Model Year: 2004, Model line: CENTURY, Model: BUICK CENTURY 2004Pages: 12, PDF Size: 0.32 MB
Page 5 of 12
5
high beams are on, a symbol
located in the instrument panel will
illuminate.
Flash-to-Pass
This feature uses the vehicle’s high
beams to alert the driver in front of you
that you intend to pass. To use it, pull
the turn signal lever toward you slightly,
but not so far that you hear a click. The
high beams will remain on for as long as
you hold the lever toward you.
Windshield Wipers
To operate the windshield wipers, turn
the WIPER band located on the multi-
function lever upward or downward.
To turn off the windshield wipers, turn
the band to OFF.
For low speed wiping, turn the band
away from you to the LO setting. For
high speeds, turn the band to HI.
Five sensitivity settings, located between
the OFF and HI settings, are provided
for a delayed wiping cycle.
Turn the band to the MIST setting for a
single wiping cycle. Hold the band until
the wipers begin, then let it go.
Windshield Washers
The windshield washer paddle is
marked PUSH and is located on top of
the multifunction lever. Push the paddle
to spray washer fluid onto the wind-
shield. The wipers will run for several
sweeps, then stop or return to your pre-
set speed.
See Section 3 of your Owner Manual.
Cruise Control
The Cruise Control feature is located at
the end of the Turn Signal/Multifunction
Lever. Cruise Control allows you to
maintain a speed of about 25 mph or
more (but not below 25 mph) without
keeping your foot on the accelerator. To
use Cruise Control:
1. Move the Cruise Control switch to ON.
2. Achieve the speed you desire.
3. Press the SET button at the tip of the
multifunction lever, then release it.
(The CRUISE light in the instrument
panel cluster will illuminate.)
4. Remove your foot from the
accelerator.
Cruise Control disengages when you
apply the brakes.
Resuming a Set Speed
To return to a preset speed after having
applied the brakes, once you’ve reached
25 mph or more, simply move the
Cruise Control switch from ON to R/A
(Resume/Accelerate).
Page 6 of 12
Getting to Know Your2004 Century6
Oil Life Monitor
The Oil Life Monitor shows an estimate
of the oil’s remaining useful life. When
the oil life index is less than 10 percent,
the CHANGE OIL SOON light will illumi-
nate in the instrument panel. After hav-
ing the oil changed, reset the system so
it can calculate when the next oil change
is required. If you change your oil prior
to the illumination of the CHANGE OIL
SOON light, reset the system.
Resetting the Oil Life Monitor
To reset the Oil Life Monitor, follow
these steps:
1. With the engine off, turn the ignition
key to RUN.
2. Fully push and release the accelera-
tor pedal slowly three times within
five seconds. (If the CHANGE OIL
SOON light flashes, the system is
resetting.)
3. Turn the key to OFF, then start the
vehicle. The oil life will change to 100
percent.
See Section 5 of your Owner Manual.
Increasing Speed While Using Cruise
Control
There are three ways to increase vehicle
speed while using Cruise Control:
1. Use the accelerator pedal to reach
the higher speed. Press the SET but-
ton, then release the button and the
accelerator pedal.
2. Move the Cruise Control switch from
ON to R/A. Hold it there until reaching
the desired speed, then release it.
3. Momentarily push the R/A button. For
every push, vehicle speed will
increase by about 1 mph (1.6 km/h).
Reducing Speed While Using Cruise
Control
To reduce speed while using Cruise
Control, use one of the following
methods:
•Press the SET button until you reach
the lower speed you want, then
release it.
•To reduce speed in smaller incre-
ments, press the SET button briefly.
Each time you press it, you’ll reduce
speed by about 1 mph (1.6 km/h).
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase
speed. After removing your foot from the
pedal, the vehicle will return to the
Cruise Control speed set earlier.
Ending Cruise Control
There are two ways to disengage Cruise
Control:
•Step lightly on the brake pedal.
•Move the cruise switch to off.
See Section 3 of your Owner Manual.
Page 11 of 12
11
Dual Climate Control System
This system controls the heating, cool-
ing and ventilation of your vehicle.
The left knob operates the fan and pro-
vides five speed settings ranging from
LO to HI. The knob on the right offers
six operating modes:
MAX:(Maximum Air Conditioning)
VENT:(Ventilation)
BI-LEVEL:(Bi-Level)
HTR:(Heater)
BLEND:This mode directs half of the air
to the floor outlets and half to the
defroster and side window outlets.
DEF:This mode directs most of the air
through the defroster and the side win-
dow outlets.
Air Conditioning and Rear Defogger
The two buttons located at the bottom of
the climate control system faceplate
control the air conditioning and the rear
window defogger:
AC:Press this button to turn the air con-
ditioning on and off. An indicator light
above the button will illuminate when the
system is on.REAR:Press this button to turn the rear
window defogger on. The defogger will
shut off automatically after about 15
minutes.
Individual Temperature Control
The driver and front passenger can
select their own air temperatures.
DRIVER:The lever on the left adjusts
the temperature for the driver’s side out-
lets. Slide the lever up to raise the tem-
perature and down to lower the temper-
ature.
PASSENGER:The lever on the right
adjusts the temperature for the passen-
ger’s side outlets. Slide the lever up to
raise the temperature and down to lower
the temperature.
See Section 3 of your Owner Manual.
Antilock Brakes (ABS)
(if equipped)
Your vehicle is equipped with an antilock
brake system (ABS), an advanced elec-
tronic brake system that will help pre-
vent a braking skid. When you start your
engine or begin to drive away, you may
hear a slight noise or feel a brake pedal
vibration — this is normal; the system is
simply checking itself.
Using Antilock Brakes:
•Never pump your brakes. Just hold
the brake pedal down firmly and
steer.
•You may feel a slight pedal pulsation
or notice some noise — that’s OK
— it means your ABS is working
properly.
See Section 4 of your Owner Manual.