headlight bulb CHRYSLER 300 SRT 2005 1.G Owners Manual

If the headlights are turned off before the ignition, they
will turn off in the normal manner.
NOTE:The lights must be turned off within 45 seconds
of turning the ignition off to activate this feature
The Headlamp delay time is programmable. Refer to
“Delay Turning Headlamps Off” in the Electronic Vehicle
Information Center section for details.
Fog Lights
The front fog light switch is on the headlamp
switch below the dimmer control. To activate the
front fog lights, turn on the parking lights or the
low beam headlights and press the fog lamp switch.
NOTE:The fog lights will operate with the low beam
headlights, or parking lights on. However, selecting the
high beam headlights will turn off the fog lights.
Turn Signals
Move the Multi-Function Lever up or down and the
arrows on each side of the instrument cluster flash to
show proper operation of the front and rear turn signal
lights. You can signal a lane change by moving the leverpartially up or down without moving beyond the detent.
Releasing the lever at the detent will provide 3 flashes.
If either light has a very fast flash rate, check for a
defective outside light bulb. If an indicator fails to light
when the lever is moved, it would suggest that the fuse
or indicator bulb is defective or there may be a circuit
failure.
NOTE:The message “Turn Signal On” will appear in
the electronic vehicle information center (EVIC), and a
continuous chime will be heard when the vehicle has
been driven more than 1 mile (1.6 km) with either turn
signal on.
Highbeam/Lowbeam Select Switch
Push the Multi-Function Lever away from you to switch
the headlights to HIGH beam. Pull the Lever towards
you to switch the headlights back to LOW beam.
Flash to Pass
You can signal another vehicle with your headlights by
lightly pulling the Multi-Function Lever toward you.
This will cause the headlights to turn on at high beam
and remain on until the lever is released.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101
3

15. Trip Odometer Button
Press this button to change the display from odometer to
either of the two trip odometer settings. The letter “A” or
“B” will appear when in the trip odometer mode. Push in
and hold the button for two seconds to reset the trip
odometer to 0 miles or kilometers. The odometer must be
in trip mode to reset.
16. High Beam Light
This light shows that the headlights are on high
beam. Push the Multi-Function lever away from
the steering wheel to switch the headlights to high
beam.
17. Transmission Range Indicator
This display indicator shows the automatic transmission
gear selection.
18. Seat Belt Reminder Light
When the ignition switch is first turned ON, this
light will turn on for 5 to 8 seconds as a bulb
check. During the bulb check, if the driver’s seat
belt is unbuckled, a chime will sound. After the bulb
check or when driving, if the driver seat belt remains
unbuckled, the Seat Belt Warning Light will flash orremain on continuously. Refer toEnhanced Driver
Seat Belt Reminder System (BeltAlert™)in the Occu-
pant Restraints section for more information.
19. Fuel Gauge
The pointer shows the level of fuel in the fuel tank when
the ignition switch is in the ON position.
20. Electronic Throttle Control (ETC) Light
This light informs you of a problem with the
Electronic Throttle Control system. If a prob-
lem is detected the light will come on while
the engine is running. Cycle the ignition key
when the vehicle has completely stopped and the gear
selector is placed in the PARK position. The light
should turn off. If the light remains lit with the engine
running your vehicle will usually be drivable, how-
ever, see your dealer for service as soon as possible. If
the light is flashing when the engine is running,
immediate service is required and you may experience
reduced performance, an elevated/rough idle or en-
gine stall and your vehicle may require towing. The
light will come on when the ignition is first turned on
138 UNDERSTANDING YOUR INSTRUMENT PANEL

▫Windshield Washers/Headlight Washers.....251
▫Exhaust System......................251
▫Cooling System.......................252
▫Hoses And Vacuum/Vapor Harnesses.......256
▫Brakes.............................257
▫Brake Fluid Level Check................258
▫Fuel System Hoses....................259
▫Automatic Transmission................259
▫Front And Rear Wheel Bearings...........260
▫Appearance Care And Protection
From Corrosion......................260
▫Cleaning The Center Console Cup Holders . . . 264

Power Distribution Centers...............264
▫Front Power Distribution Center...........264▫Rear Power Distribution Center...........266

Vehicle Storage........................268

Replacement Light Bulbs................269

Bulb Replacement......................270
▫Low Beam Headlamp, High Beam Headlamp,
And Park/Turn Lamp..................270
▫Tail/Stop, Tail, Turn Signal Lamp, And Backup
Lamp..............................272
▫License Lamp........................274

Fluids And Capacities...................275

Recommended Fluids, Lubricants And
Genuine Parts
.........................276
▫Engine.............................276
▫Chassis............................276
236 MAINTAINING YOUR VEHICLE

BULB REPLACEMENT
Low Beam Headlamp, High Beam Headlamp, and
Park/Turn Lamp
High Intensity Discharge Headlights (HID)
The headlights are a type of high voltage discharge tube.
High voltage can remain in the circuit even with the
headlight switch off and the key removed.Because of
this, you should not attempt to service a headlight bulb
yourself. If a headlight bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high tension occurs at the bulb sockets of
High Intensity Discharge (HID) headlights when the
headlight switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced prop-
erly. See your authorized dealer for service.
NOTE:When HID headlights are turned on there is a
blue hue to the lights. This diminishes and becomes more
white after approximately 10 seconds, as the system
charges.
•Open the hood.
•Twist the appropriate bulb socket assembly counter-
clockwise and pull out. Pull the bulb out of the socket
assembly.
NOTE:Removal of the air cleaner filter housing may be
necessary prior to replacing bulbs on driver’s side head-
lamp assembly.
270 MAINTAINING YOUR VEHICLE

Hoses............................256,259
Ignition
Key ................................ 11
Illuminated Entry....................... 15
Immobilizer............................ 12
Infant Restraint......................... 49
Information Center, Vehicle............... 140
Instrument Cluster...................133,134
Instrument Panel and Controls............. 132
Instrument Panel Lens Cleaning............ 263
Interior Appearance Care................. 262
Interior Fuses.......................... 264
Interior Lights.......................... 97
Intermittent Wipers..................... 104
Introduction............................ 4
Jump Starting......................... 229
Key, Programming....................... 14
Key, Replacement....................... 13
Key, Sentry............................ 12
Key-In Reminder........................ 12Keyless Entry System..................... 19
Keys................................. 11
Knee Bolster........................... 35
Lap/Shoulder Belts...................... 29
LATCH
(Lower Anchors and Tether for CHildren)..... 53
Latch Plate............................ 30
Latches
Hood............................... 95
Lead Free Gasoline...................... 214
Lights..............................58,97
Airbag.......................40,47,57,135
Anti-Lock........................... 135
Automatic Headlights.................. 100
Brake Warning....................... 136
Bulb Replacement..................... 269
Courtesy/Reading..................... 97
Daytime Running..................... 100
Dimmer Switch, Headlight............99,101
Engine Temperature Warning............ 135
Fog .............................101,134
Hazard Warning Flasher................ 224
INDEX 309
10