tyre pressure Citroen C2 DAG 2008 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008, Model line: C2 DAG, Model: Citroen C2 DAG 2008 1.GPages: 178, PDF Size: 5.56 MB
Page 104 of 178
A
119
V
C H A N G I N G A W H E E L
T h e j a c k i s s p e c i fi c t o y o u r v e h i c l e , d o n o t u s e i t f o r a n y o t h e r purposes.
With a spare wheel, drive cautiously.
Access to the spare wheel
Open the lower tailgate.
Remove the blank A with the aid of the ignition key, to insert the exten-sion for the wheelbrace.
Slacken the spare wheel carrier screw.
Lift the carrier to release the retain-ing hook, then disengage it.
To reposition the spare wheel
Having repositioned the jack and its handle in its protection box in the wheel, slide the wheel into the carrier.
Lift the carrier to secure it in the safety hook.
Retighten the screw from inside the boot compartment.
Stow the wheelbrace and exten-sion.
Reposition the blank A.
Tyre pressures
This is indicated on the label on the f r o n t d o o r p i l l a r . S e e " V e h i c l e i d e n t i - fi c a t i o n " a n d " U s e r P r e c a u t i o n s " .
ADVICE
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e type of wheel.
If the type of wheel is changed, check with your CITROËN dealer If the type of wheel is changed, wheel is changed,
that the wheel bolts are compatible with the new wheels.
Page 106 of 178
1 2 1
V
Because the aerosol is pressurised, do not expose it to temperatures higher than 50 °C.
After provisionally repairing a tyre using the repair aerosol, you are advised not to drive at over 80 km/h.
If your vehicle has no spare wheel, a repair aerosol is to be found in the boot.
Using the repair aerosol
See also the user instructions on the aerosol.Remove, if possible, the object which has caused the punc-ture.
Orient the wheel so that the valve is at ten o’clock or two o’clock.Shake the aerosol vigorously (in cold weather warm it in your hands for a few minutes).
With one hand hold the valve connector clear of the rim hole, with the other hand press the e n d o f t h e a e r o s o l n o z z l e fi r m l y onto the connector, keeping it in the line of the valve.Firmly maintain the pressure for one minute.
Rapidly remove the aerosol and immediately drive for around six miles.
R e i n fl a t e t h e t y r e a n d c h e c k i t s condition after some ten hours.
After using the repair aerosol, you should have the condition o f t h e t y r e , a s w e l l a s i t s i n fl a t i o n pressure, inspected.
Page 113 of 178
A
A
D
B
C
1 2 8
VI
V E H I C L E I D E N T I F I C A T I O N
Self-adhesive manufacturer’s plateA. On the LH door aperture, above the striker plate.1. EU type approval number.2. V e h i c l e i d e n t i fi c a t i o n N o . ( V I N ) .3. Gross vehicle weight.4. Gross train weight.5. Maximum weight on front axle.6. Maximum weight on rear axle.B. Body serial numberC. Factory serial no. under the windscreenD. Paint colour codeTyre referenceTyre pressures
T h e v e h i c l e t y p e a n d t h e i d e n t i fi c a t i o n n u m b e r a r e a l s o i n d i c a t e d o n t h e registration document.
All CITROËN original replacement parts are available exclusively w ithin the dealer network.
For your safety and in order to remain within the terms of the guarantee, you are advised to use only CITROËN replacement parts.For your safety and in order to remain within the terms of order to remain