gearbox FIAT 500 2008 2.G Start And Stop Supplement Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2008, Model line: 500, Model: FIAT 500 2008 2.GPages: 4, PDF Size: 0.42 MB
Page 2 of 4
2
FOREWORD
The Start&Stopdevice automatically stops
the engine each time the vehicle is stationary
and starts it again when the driver is about to
engage a gear.
This improves the efficiency of the vehicle by
reducing consumption, the emission of harm-
ful gases and noise pollution.
The system is activated each time the car is
started
fig. 1
F0S0270m
fig. 2F0S0271m
OPERATING MODES
Engine cut out mode
With manual transmission
With the vehicle stationary, the engine cuts out
with the gearbox in neutral and the clutch ped-
al released.
With robotized transmission
The engine cuts out if the car stops with the
brake pedal pressed.
This condition can be maintained even if the
brake pedal is not pressed, if the gear lever is
in position N.
Note:The engine can only be stopped auto-
matically after a speed of about 10 Km/h is
reached, to prevent the engine from being re-
peatedly stopped when driving at walking pace.
The engine being stopped is signalled by the
warning light fig. 1in the instrument panel, de-
pending on the trim level.
Engine restarting mode
With normal transmission
Press the clutch pedal to allow the engine to
be restarted.
With robotized transmission
If the gear lever is in position N, place it in any
other gear, otherwise release the brake pedal
or move the gear lever to (+), (–) or R.MANUAL ACTIVATION AND
DEACTIVATION
The device can be activated/deactivated via the
button in the dashboard A-fig. 2. When the
system is deactivated the “Start&Stop OFF”
warning light is visible in the dashboard fig. 3.
In addition, on some versions additional infor-
mation concerning the deactivation or activa-
tion of the Start&Stop is given through a mes-
sage in the display
fig. 3
F0S0272m
604_39_858 500 START&STOP GB 6-10-2008 11:26 Pagina 2
Page 4 of 4
4
INACTIVITY OF THE CAR fig. 5
In the case of inactivity of the car, special care
must be taken to disconnect the battery elec-
trical power supply. This procedure is carried
out by disconnect the rapid release negative
terminal Afrom the negative false pole Bbe-
cause there is a battery status monitoring sen-
sor Dat the negative battery pole Cwhich
should never be disconnected except if the ac-
tual battery is replaced.
If the battery is replaced, always
go to a Fiat Dealer. Replace the
battery with one of the same type (HEAVY
DUTY) and with the same specifications.
WARNING
EMERGENCY STARTING fig. 6
In the case of emergency starting with an auxil-
iary battery, never connect the negative lead (–)
of the auxiliary battery to the negative pole Cof
the car battery, but rather to either the false pole
Bor to an engine/gearbox earth pointfig. 5
F0S0274m
fig. 6F0S0275m
fig. 7F0S0276m
IMPORTANT NOTES
Before opening the bonnet, make
sure that the car is switched off
and the key is in the OFF position. Follow
the instructions on the plate near the front
crossmember fig. 7. It is advisable to extract
the key when there are other people in the
car. The car should always be left after the
key has been removed or turned to the OFF
position. During refuelling operations, it is
necessary to make sure that the car is off
with the ignition key in the OFF position.
WARNING
For cars with a robotized transmis-
sion, if the engine cuts out automat-
ically on a gradient, it is advisable to restart the
engine operating the gear lever towards (+) or
(–) without releasing the brake pedal. For vehi-
cles with robotized transmission where the Hill
Holder function is present, if the engine cuts out
automatically whilst driving uphill, it is advisable
to restart it by operating the gear lever towards
(+) or towards (–) without releasing the brake
pedal to make the Hill Holder function available.
WARNING
If you want to make the most of
climate comfort, the Start&Stop
system can be disabled to allow continu-
ous operation of the climate control system.
WARNING
Fiat Group Automobiles S.p.A. - Customer Services - Technical Services - Service Engineering - Largo Senatore G. Agnelli, 5 - 10040 Volvera - Torino (Italia)
Print no. 604.39.858 - 10/2008 - 1stEdition
fig. 4F0S0273m
604_39_858 500 START&STOP GB 6-10-2008 11:26 Pagina 4