wheel FIAT 500L LIVING 2018 Owner handbook (in English)

USE OF THE OWNER HANDBOOK
OPERATING INSTRUCTIONS
Each time direction instructions (left/right or forwards/backwards) about the car are given, these must be understood as
regarding an occupant in the driver's seat. Special cases not complying with this rule will be specified as appropriate in the text.
The figures in the Owner Handbook are provided by way of example only: this might imply that some details of the image do
not correspond to the actual arrangement of your car. In addition, the Handbook has been conceived considering vehicles with
steering wheel on the left side; it is therefore possible that on vehicles with steering wheel on the right side, the position or
construction of some controls is not exactly mirror-like with respect to the figure.
To identify the chapter with the information needed you can consult the index at the end of this Owner Handbook.
Chapters can be rapidly identified with dedicated graphic tabs, at the side of each odd page. A few pages further there is a key
for getting to know the chapter order and the relevant symbols in the tabs. There is in any case a textual indication of the
current chapter at the side of each even page.
WARNINGS AND PRECAUTIONS
While reading this Owner Handbook you will find a series ofWARNINGSto prevent procedures that could damage your
vehicle.
There are alsoPRECAUTIONSthat must be carefully followed to prevent incorrect use of the components of the vehicle,
which could cause accidents or injuries.
Therefore, allWARNINGSandPRECAUTIONSmust always be followed carefully.
WARNINGSandPRECAUTIONSare recalled in the text with the following symbols:
personal safety;
vehicle safety;
environmental protection.
NOTE These symbols, when necessary, are indicated besides the title or at the end of the line and are followed by a number.
That number recalls the corresponding warning at the end of the relevant section.

SYMBOLS
Some car components have coloured labels whose symbols indicate precautions to be observed when using this component.
A plate summarising these symbols can also be found under the bonnet.
CHANGES/ALTERATIONS TO THE CAR
IMPORTANT Any change or alteration of the car might seriously affect its safety and road holding, thus causing accidents, in
which the occupants could even be fatally injured.
IMPORTANT The use of these devices inside the passenger compartment (without an external aerial) may cause the electrical
systems to malfunction. This could compromise the safety of the vehicle in addition to constituting a potential hazard for
passengers' health.
IMPORTANT Take care when fitting additional spoilers, alloy wheel rims or non-standard wheel hubs: they could reduce the
ventilation of the brakes and affect efficiency under sharp, repeated braking or on long descents. Make sure that nothing
obstructs the pedal stroke (mats, etc.).

KNOWING YOUR CAR
In-depth knowledge of your new vehicle
starts here.
The handbook that you are reading
simply and directly explains how it
is made and how it works.
That’s why we advise you to read it
seated comfortably on board, so that
you can see immediately what is
described here for yourself.DASHBOARD ................................. 10
THE FIAT CODE SYSTEM ............... 12
KEYS .............................................. 12
IGNITION DEVICE ........................... 14
SEATS ............................................ 15
HEAD RESTRAINTS ........................ 18
STEERING WHEEL ......................... 19
REAR VIEW MIRRORS .................... 19
CLIMATE CONTROL SYSTEM ....... 21
EXTERIOR LIGHTS ......................... 24
INTERIOR LIGHTS .......................... 26
WINDSCREEN WIPER/REAR
WINDOW WIPER ............................ 27
FIXED GLASS ROOF ....................... 29
ELECTRIC SUNROOF ..................... 30
DOORS ........................................... 32
ELECTRIC WINDOWS .................... 33
BONNET ......................................... 35
LUGGAGE COMPARTMENT ........... 36
DUALDRIVE ELECTRIC POWER
STEERING ...................................... 38
VERSION WITH LPG SYSTEM ........ 39
VERSION WITH METHANE
SYSTEM (NATURAL POWER) ......... 41
9

DASHBOARD
The presence and position of controls, instruments and gauges may vary depending on the versions. On some versions, the
dashboard and controls may be backlit.
1. Adjustable and directable air diffusers / 2. Exterior light control stalk / 3. Controls on the steering wheel: Setup menu and
interaction withUconnect™system / 4. Instrument panel / 5. Controls on the steering wheel: Cruise Control, Speed Limiter /
6. Windscreen/rear window wiper lever / 7. Fixed upper air vent / 8.Uconnect™system / 9. Upper storage compartment
/
10. Passenger front airbag / 11. Lower compartment box / 12. Adjustable and directable central air vents / 13. Manual climate
control (for versions/markets, where provided) or automatic dual zone climate control (for versions/markets, where provided) /
14. Cigar lighter (for versions/markets, where provided) / 15. USB port/AUX socket (for versions/markets, where provided) /
16. Mode Selector / 17. Control buttons / 18. Ignition device / 19. Driver knee bag (for versions/markets, where provided) /
20. Driver's front airbag / 21. Dashboard fusebox access flap
1F0Y0604C
10
KNOWING YOUR CAR

RIGHT-HAND DRIVE VERSIONS
1. Adjustable and directable air diffusers / 2. Upper storage compartment /3. Passenger front airbag / 4. Adjustable and
directable central air vents / 5.Uconnect™system / 6. Fixed upper air vent / 7. Exterior light control stalk / 8. Controls on the
steering wheel: Setup menu and interaction withUconnect™system/ 9. Instrument panel / 10. Windscreen/rear window
wiper lever / 11. Controls on the steering wheel: Cruise Control, Speed Limiter / 12. Ignition device / 13. Driver's front airbag /
14. Driver knee bag (for versions/markets, where provided) / 15. Manual climate control (for versions/markets, where provided)
or automatic dual zone climate control (for versions/markets, where provided) / 16. Mode Selector / 17. USB port/AUX socket
(for versions/markets, where provided) / 18. Cigar lighter (for versions/markets, where provided) / 19. Control buttons /
20. Lower compartment box and dashboard fusebox access
13
2F0Y0900C
11

WARNING
1)Button B fig. 4should only be pressed
when the key is away from the body, in
particular from the eyes and from objects
that can be spoilt (e.g. clothes). Do not
leave the key unattended to avoid the
button being accidentally pressed while it
is being handled, e.g. by a child.
2)Once the safe lock system is engaged, it
is impossible to open the doors from
inside the car. Therefore, before getting out
of the car check that there is no-one left
on board.
WARNING
1)The electronic components inside the
key may be damaged if the key is
subjected to strong shocks. In order to
ensure complete efficiency of the
electronic devices inside the key, it should
never be exposed to direct sunlight.
WARNING
1)Used batteries should be disposed of,
as specified by law, in the special
containers, otherwise take them to a Fiat
Dealership, which will deal with their
disposal.
IGNITION DEVICE
3) 4) 5) 6)
The key can be turned to three different
positions fig. 6:
STOP: engine off, key can be
removed, steering column locked.
Some electrical devices (e.g. central
door locking system, etc.) can operate;
MAR: driving position. All electrical
devices are enabled;
AVV: engine starting.
The ignition device is fitted with a safety
system that requires the ignition key
to be turned back to STOP if the engine
does not start, before the starting
operation can be repeated.STEERING LOCK
Engagement: when at STOP, remove
the key and turn the steering wheel until
it locks.
Disengagement:move the steering
wheel slightly as you turn the ignition
key to MAR.
WARNING
3)If the ignition device has been tampered
with (e.g. an attempted theft), have it
checked by a Fiat Dealership before driving
again.
4)Always remove the key when you leave
your car to prevent someone from
accidentally operating the controls.
Remember to engage the handbrake.
Engage 1
stgear if the car is parked uphill or
reverse if the car is parked downhill. Never
leave children unattended in the vehicle.
5)It is absolutely forbidden to carry out any
after-market operation involving steering
system or steering column modifications
(e.g.: installation of anti-theft device) that
could badly affect performance and safety,
invalidate the warranty and also result in
non-compliance of the car with type-
approval requirements.
6)Never remove the key while the car is
moving. The steering wheel would
automatically lock as soon as you try to
turn it. This holds true for cars being towed
as well.
6F0Y0654C
14
KNOWING YOUR CAR

SEATS
7) 9)2) 3)
FRONT SEATS
Longitudinal adjustment
Lift lever A fig. 7, holding it in the central
zone and push the seat forwards or
backwards: in the driving position your
arms should rest on the rim of the
steering wheel.
8)
Height adjustment
Adjust lever B fig. 8 upwards or
downwards to obtain the required
height.Backrest angle adjustment
Move lever C fig. 9 to adjust the
backrest angle, accompanying it with
the movement of the torso (operate the
lever until the desired position is
reached, then release it).Electric lumbar adjustment
(for versions/markets, where provided)
With the key turned to MAR, press
button A fig. 10 to adjust. Release the
button when you reach the desired
position.
Electric seat heating
(for versions/markets, where provided)
With the ignition key turned to MAR,
press button B fig. 10 to switch the
function on/off. When the function
is enabled, the LED on the button turns
on.
Table
(for versions/markets, where provided)
10)
On some versions, behind the front
seat backrest there is a folding support
surface equipped with cup/can holders.
In the rear of the backrests there is
also an object retaining net.
7F0Y0384C
8F0Y0216C
9F0Y0217C
10F0Y0215C
15

STEERING WHEEL
17) 18)ADJUSTMENTS
The steering wheel can be adjusted
axially and vertically. To adjust, move
lever A fig. 19 downwards to position 1,
then adjust the steering wheel to the
most suitable position and lock it in
position by moving lever A to position
2.
WARNING
17)All adjustments must be carried out
only with the car stationary and engine off.
18)It is absolutely forbidden to carry out
any after-market operation involving
steering system or steering column
modifications (e.g. installation of anti-theft
device) that could adversely affect
performance and safety, invalidate the
warranty and also result in the car not
meeting type-approval requirements.
REAR VIEW
MIRRORS
INTERNAL MIRROR
The mirror is fitted with a safety device
that causes its release in the event of
a violent impact with the passenger.
Operate lever A fig. 20 to adjust the
mirror into two different positions:
normal or anti-glare.
ELECTROCHROMIC
INTERIOR MIRROR
(for versions/markets, where provided)
The electrochromic mirrorfig. 21 has
an ON/OFF button to activate/
deactivate the electrochromic function.
When reverse is engaged, the mirror
is automatically set for daytime use.DOOR MIRRORS
Manual adjustment
From the inside of the car, operate lever
A fig. 22 to adjust the mirror.
Manual folding
If necessary, fold the mirrors, moving
them from the "fully open" to the "fully
closed" position.
19F0Y0605C20F0Y0223C
21F0Y0225C
22F0Y0275C
19

If the front and rear fog lights are on
when the engine is stopped, they will
switch off. When the engine is
restarted, the fog lights will remain off
until switched on again by pressing the
button.
AUTOMATIC LIGHTING
CONTROL (AUTOLIGHT)
(dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor located
on the windscreen, which detects
variations in outside light levels.
Activation: turn ring nut A fig. 27 to
.
With dusk sensor active, with daytime
running lights (DRL) on, it is not
possible to keep the main beam
headlights on constantly; only flashing
is permitted. In these conditions, the
main beam headlights can be turned on
by turning the ring nut to
and
pushing the stalk towards the
dashboard; otherwise, wait until the
dusk sensor indicates a low light level
(dipped beam headlights on).
On automatic sensor controlled
deactivation, the dipped beam
headlights are deactivated first,
followed by the side lights a few
seconds later.IMPORTANT The sensor cannot detect
the presence of fog. These lights must
therefore be switched on manually in
these circumstances.
MAIN BEAM HEADLIGHTS
With ring nut in position
, push the
stalk forward toward the dashboard
(stable position) to turn on the lights.
The
warning light switches on
in the instrument panel.
The lights are switched off by pulling
the stalk towards the steering wheel.
FLASHING
Pull the left stalk fig. 29 toward yourself,
to the stable position; the stalk goes
back to the central stable position when
it is released. With main beam
headlights on, the
warning light on
the instrument panel will come on at
the same time.DIRECTION INDICATORS
Place the lever in the (stable) position:
upwards:right-hand direction indicator
activation/downwards:left-hand
direction indicator activation.
The
orwarning light will blink on
the instrument panel.
The direction indicators switch off
automatically when the steering wheel
is straightened.
"Lane change" function
If you wish to signal a lane change,
place the left stalk in the unstable
position for less than half a second. The
direction indicator on the side selected
will flash five times and then switch
off automatically.
“Cornering lights”
When the dipped beam headlights are
on and the speed is below 40 km/h,
if the steering wheel rotation angle
is large or the direction indicators are
on, a light (incorporated in the fog light)
will come on on the relevant side to
improve visibility at night time.
29F0Y0771C
25

COURTESY LIGHTS
The function can be enabled and its
times set use the "Settings" Menu
of theUconnect™system. When the
doors are unlocked, the side lights
and puddle lights come on for the time
set in the menu.
Once any door is opened, the lights
remain on for a further 180 seconds, or
for a further 10 seconds after the door
is closed.
“FOLLOW ME HOME”
DEVICE
This allows the space in front of the car
to be lit for a set time.
Activation
With the key turned to STOP or
removed, pull the left-hand stalk
towards the steering wheel within 2
minutes from when the engine is turned
off. Each time the stalk is operated,
the lights stay on for an extra 30
seconds up to a maximum of 210
seconds. When this time is up the lights
automatically switch off.Each time the stalk is operated, the
warning light
on the instrument
panel switches on. The display shows a
message and the time set for the
function. The
warning light comes
on when the stalk is first operated
and stays on until the function is
automatically deactivated.
Deactivation
Keep the stalk pulled towards the
steering wheel for more than 2
seconds.
WARNING
20)The daytime running lights are an
alternative to the dipped beam headlights
for driving during the daytime in countries
where it is compulsory to have lights on
during the day; where it is not compulsory,
the use of daytime running lights is
permitted.
21)Daytime running lights cannot replace
dipped beam headlights when driving at
night or through tunnels. The use of
daytime running lights is governed by the
Highway Code of the country in which you
are driving. Comply with legal
requirements.
INTERIOR LIGHTS
FRONT CEILING LIGHT
Switch A fig. 30 is used to switch on/off
the roof light bulbs.
Switch A positions:
central position: lights C and E
switch on/off when the doors are
opened/closed;
pressed to the left (position OFF):
lights C and E are always switched off;
pressed to the right (position):
lights C and D are always switched on.
The lights switch on/off progressively,
controlled by a timer, when the driver
enters and exits the car.
30F0Y0098C
26
KNOWING YOUR CAR