door lock FIAT 500X 2014 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2014, Model line: 500X, Model: FIAT 500X 2014 2.GPages: 476, PDF Size: 5.32 MB
Page 22 of 476
DOORS .............................36
▫ Manual Locking/Unlocking ..............36
▫ Central Lock/Unlock ...................37
▫ Keyless Enter-N-Go ...................38
▫ Child Locks .........................44
SEATS ..............................46
▫ Manual Adjustment Front Seats ...........46
▫ Power Adjustment Front Seats — If Equipped .48
▫ Heated Seats — If Equipped .............49
▫ Rear Seats ..........................50
HEAD RESTRAINTS ....................53
▫ Front Head Restraints ..................53
▫ Rear Head Restraints ...................54
STEERING WHEEL .....................55
▫ Tilt/Telescoping Steering Column .........55
▫ Heated Steering Wheel — If Equipped ......56
MIRRORS ...........................57 ▫
Inside Day/Night Mirror ...............57
▫ Auto Dimming Mirror — If Equipped .......57
▫ Outside Mirrors ......................58
▫ Heated Mirrors — If Equipped ...........59
BLIND SPOT MONITORING (BSM) — IF
EQUIPPED ...........................59
▫ Rear Cross Path (RCP) .................64
▫ Mode Of Operation ....................65
▫ Blind Spot Monitoring Fault Warnings ......66
▫ General Information ...................66
EXTERIOR LIGHTS .....................66
▫ Headlights ..........................66
▫ Automatic Lighting — If Equipped ........67
▫ Daytime Running Lights (DRL) — If
Equipped ..........................68
▫ Front Fog Lights — If Equipped ..........68
▫ Parking Lights .......................68
▫ Headlight Delay ......................68
20 GETTING TO KNOW YOUR VEHICLE
Page 25 of 476
KEYS
Electronic Key Fob
On versions equipped withKeyless Enter-N-Go,the
car is equipped with an electronic key fob.
The key fob with Remote Control contains a Remote
Keyless Entry key fob. The Remote Keyless Entry
system allows you to lock or unlock the doors and
liftgate or activate the Panic Alarm from distances up to
approximately 66 ft (20 m) using a handheld key fob.
The key fob does not need to be pointed at the vehicle
to activate the system.
NOTE: In the ON/RUN position, the trunk release
button is disabled. Only the unlock button is enabled.
Keyless Enter-N-Go Key Fob
1 — Door Lock Button
2 — Remote Start Button
3 — Panic Button
4 — Emergency Key
5 — Door Unlock Button
4
GETTING TO KNOW YOUR VEHICLE 23
Page 26 of 476
Key Fob Operation
Unlocking Doors And Liftgate
The driver ’s door may be unlocked by inserting the
vehicle key into the exterior driver’s door lock cylinder.
To unlock all the doors, push the interior power door
unlock button on the door panel.
Push and release the unlock button on the key fob once
to unlock the driver’s door or twice within five seconds
to unlock all doors and the liftgate. The turn signal
lights will flash to acknowledge the unlock signal. The
illuminated entry system will also turn on.
1st Press Of Key Fob Unlocks Feature
This feature lets you program the system to unlock
either the driver’s door or all doors on the first push of
the unlock button on the key fob. To change the current
setting, refer to “Uconnect Settings” in “Multimedia”
for further information.
NOTE:If the vehicle is equipped with Passive Entry,
refer to “Keyless Enter-N-Go” in “Getting To Know
Your Vehicle” for further information.
Emergency Key Release/Removal
1 — Emergency Key Release Button
2 — Emergency Key 24 GETTING TO KNOW YOUR VEHICLE
Page 27 of 476
Locking Doors And Liftgate
The doors may be locked by inserting the vehicle key
into the exterior driver’s door lock cylinder.
Push and release the lock button on the key fob to lock
all doors and liftgate. The turn signal lights will flash
and the horn will chirp to acknowledge the signal.
Settings in the radio can change to lights only, chirp
only, or both.
If the vehicle is equipped with Passive Entry, refer to
“Keyless Enter-N-Go” in “Getting To Know Your Ve-
hicle” for further information.
Key Fob With Remote Control And Integrated Vehicle
Key
If one or more doors are open, or the liftgate is open, the
doors will lock when you push the lock button on the
key fob. This is signaled by a quick flash of the turn
signals.
Vehicles With Keyless Enter-N-Go
If one or more doors are open, or the liftgate is open, the
doors will lock when you push the lock button on the
key fob. The doors will unlock again only if the key is
inside the passenger compartment.NOTE:
•
The current setting can be changed within the instru-
ment cluster display menu or in the Uconnect Set-
tings so that the system will allow/inhibit the ability
to lock the doors when one or more of them are open.
• Refer to “Instrument Cluster Display” in “Getting To
Know Your Instrument Panel” or “Uconnect Set-
tings” in “Multimedia” for further information.
Replacing The Battery In The Key Fob With
Remote Control
The recommended replacement battery is one CR2032
battery.
NOTE:
• Perchlorate Material — special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
• Do not touch the battery terminals that are on the
back housing or the printed circuit board.
Separating Keyless Enter-N-Go Key Fob Case
1. Remove the emergency key by sliding the mechani- cal latch on the back of the key fob sideways with
your thumb. Then, pull the key out with your other
hand.
4
GETTING TO KNOW YOUR VEHICLE 25
Page 29 of 476
CAUTION!
•Always remove the key fobs from the vehicle and
lock all doors when leaving the vehicle unat-
tended.
• For vehicles equipped with Keyless Enter-N-Go
— Ignition, always remember to place the igni-
tion in the OFF mode.
Duplication of key fobs may be performed at an autho-
rized dealer. This procedure consists of programming a
blank key fob to the vehicle electronics. A blank key fob
is one that has never been programmed.
NOTE: When having the Sentry Key Immobilizer Sys-
tem serviced, bring all vehicle keys with you to an
authorized dealer.
General Information
The following regulatory statement applies to all Radio
Frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user ’s authority to operate the equipment.
IGNITION SWITCH
Operation
Your vehicle uses a keyless ignition system. The keyless
ignition system consists of a Remote Keyless Entry key
fob with a Keyless Push Button Ignition.
Electronic Key
This Keyless Enter-N-Go system feature allows the
driver to operate the ignition switch with the push of a
button as long as the key fob is in the passenger
compartment.
The Keyless Push Button Ignition has three operating
positions. The three positions are STOP, RUN, and
START.
4
GETTING TO KNOW YOUR VEHICLE 27
Page 31 of 476
WARNING!(Continued)
•Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Chil-
dren should be warned not to touch the parking
brake, brake pedal or the gear selector.
• Do not leave the key fob in or near the vehicle, or
in a location accessible to children, and do not
leave the ignition of a vehicle equipped with
Keyless Enter-N-Go in the ON/RUN mode. A
child could operate power windows, other con-
trols, or move the vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up
may cause serious injury or death.
CAUTION!
An unlocked car is an invitation. Always remove
the key from the ignition and lock all doors when
leaving the vehicle unattended.
NOTE: Refer to Starting the Engine inStarting And
Operating for further information.
General Information
The following regulatory statement applies to all radio
frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user ’s authority to operate the equipment.
REMOTE STARTING SYSTEM — IF EQUIPPED
This system uses the key fob to start the
engine conveniently from outside the vehicle
while still maintaining security. The system
has a range of 328 ft (100 m).
4
GETTING TO KNOW YOUR VEHICLE 29
Page 33 of 476
WARNING!
•Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Mon-
oxide (CO) which is odorless and colorless. Car-
bon Monoxide is poisonous and can cause serious
injury or death when inhaled.
• Keep key fobs away from children. Operation of
the Remote Start System, windows, door locks or
other controls could cause serious injury or death.
To Enter Remote Start Mode
Push and release the remote start button on
the key fob twice within five seconds. The
vehicle doors will lock, the turn signals will
flash, and the horn will chirp twice. Then, the
engine will start, and the vehicle will remain in the
Remote Start mode for a 15-minute cycle.
NOTE:
• If an engine fault is present or fuel level is low, the
vehicle will start and then shut down in 10 seconds.
• The park lamps will turn on and remain on during
remote start mode. •
For security, power window operation is disabled
when the vehicle is in the remote start mode.
To Exit Remote Start Mode Without Driving The
Vehicle
Push and release the remote start button one time or
allow the engine to run for the entire 15-minute cycle.
NOTE: To avoid unintentional shutdowns, the system
will disable with a one time push of the remote start
button for two seconds after receiving a valid remote
start request.
To Exit Remote Start Mode And Drive The
Vehicle
Before the end of 15-minute cycle, push and release the
unlock button on the key fob to unlock the doors and
disarm the vehicle security alarm (if equipped). Then,
prior to the end of the 15-minute cycle, for vehicles
equipped with the Keyless Enter-N-Go feature, push
and release the keyless ignition button.
NOTE: For vehicles equipped with the Keyless Enter-
N-Go feature, the message “Remote Start Active —
Push Start Button” will display in the instrument clus-
ter display until you push the keyless ignition button.
4
GETTING TO KNOW YOUR VEHICLE 31
Page 35 of 476
operate the vehicle. The system will not allow the
engine to crank if an invalid key fob tries to start the
engine.
After placing the ignition to the ON/RUN position, if
there is a problem with the system, the vehicle security
light will turn on. This condition will result in the
engine being shut off after two seconds.
Should this occur, have the vehicle serviced as soon as
possible by an authorized dealer.
CAUTION!
•Do not make modifications or alterations to the
immobilizer system. Modifications or alterations
to the immobilization system may result in a loss
of security protection.
• The Sentry Key Immobilizer system is not com-
patible with some aftermarket remote starting
systems. Use of these systems may result in
vehicle starting problems and loss of security
protection.
General Information
The following regulatory statement applies to all radio
frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
NOTE: Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user ’s authority to operate the equipment.
VEHICLE SECURITY ALARM
The vehicle security alarm monitors the vehicle doors
for unauthorized entry and if the ignition switch is
cycled to the ON/RUN position without a valid key.
While the vehicle security alarm is armed, interior
switches for door locks and liftgate release are disabled.
4
GETTING TO KNOW YOUR VEHICLE 33
Page 36 of 476
If something triggers the alarm, the vehicle security
alarm will provide the following audible and visible
signals:
•Horn will pulse.
• Park lamps and/or turn signals will flash.
• Vehicle security light in the instrument cluster will
flash.To Arm The System
Follow these steps to arm the vehicle security alarm:
1. Make sure the vehicles ignition is cycled to the STOP/OFF position (refer to Starting The Enginein
Starting And Operating for further information).
• For vehicles equipped with Keyless Enter-N-Go,
make sure the vehicle ignition system is OFF.
2. Perform one of the following methods to lock the vehicle:
• Push lock on the interior power door lock switch
with the driver and/or passenger door open.
• Push the lock button on the exterior Passive Entry
Door Handle with a valid key fob available in the
same exterior zone (for further information, refer to
Keyless Enter-N-Go inGetting To Know Your
Vehicle”).
• Push the lock button on the key fob.
3. If any doors are open, close them.
Vehicle Security Light Location
34 GETTING TO KNOW YOUR VEHICLE
Page 37 of 476
NOTE:•If a second chime is heard after approximately four
seconds from arming the alarm, disarm the alarm
by pushing the unlock button. Check for the correct
closure of doors and liftgate, then reactivate the
system by following steps 1 and 2.
• If a second chime is heard after approximately four
seconds from arming the alarm, even with the
doors and liftgate properly closed, a fault may have
occurred during the arming operation. If this oc-
curs, contact your authorized dealer.
To Disarm The System
The vehicle security alarm can be disarmed using any of
the following methods:
• Push the unlock button on the key fob.
• Grasp the Passive Entry Unlock Door Handle with a
valid key fob available in the same exterior zone (if
equipped). Refer to Keyless Enter-N-Go inGetting
To Know Your Vehicle for further information. •
Cycle the vehicle ignition system out of the STOP/
OFF/LOCK position.
– For vehicles equipped with Keyless Enter-N-Go, push the Keyless Enter-N-Go START/STOP but-
ton (requires at least one valid key fob in the
vehicle).
NOTE:
• The driver’s door key cylinder cannot arm or disarm
the vehicle security alarm.
• When the vehicle security alarm is armed, the inte-
rior power door lock switches will not unlock the
doors.
The vehicle security alarm is designed to protect your
vehicle. However, you can create conditions where the
system will give you a false alarm. If one of the
previously described arming sequences has occurred,
the vehicle security alarm will arm regardless of
whether you are in the vehicle or not. If you remain in
the vehicle and open a door, the alarm will sound. If this
occurs, disarm the vehicle security alarm.
If the vehicle security alarm is armed and the battery
becomes disconnected, the vehicle security alarm will
remain armed when the battery is reconnected.
4
GETTING TO KNOW YOUR VEHICLE 35