rims FIAT BRAVO 2013 2.G Owners Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2013, Model line: BRAVO, Model: FIAT BRAVO 2013 2.GPages: 299, PDF Size: 5.86 MB
Page 2 of 299
We really know your car because we invented, designed and built it: we really know every single detail.
At Fiat Service authorised workshopsyou can find technicians directly trained by us,
offering quality and professionalism for all service operations.
Fiat workshops are always close to you for the regular servicing operations, season checks
and practical recommendations by our experts.
With Fiat Genuine Parts you keep the reliability, comfort and performance features
of your new car unchanged in time: that's why you bought it for.
Always ask for Genuine Parts for the components used on our cars; we recommend them because
they come from our steady commitment in research and development of highly innovative technologies.
For all these reasons: rely on Genuine Parts, because they are the only ones designed
by Fiat for your car.
SAFETY:
BRAKING SYSTEMENVIRONMENT: PARTICULATE FILTERS,
CLIMATE CONTROL MAINTENANCECOMFORT: SUSPENSION
AND WINDSCREEN WIPERS PERFORMANCE: SPARK PLUGS,
INJECTORS AND BATTERIESLINEACCESSORI
ROOF RACK BARS, WHEEL RIMS
WHY CHOOSING
GENUINE PARTS
BRAVO LUM GB:BRAVO UM GB 24-05-2012 14:30 Pagina 2
Page 126 of 299
send the relative indications to the instrument
panel only after the vehicle has been in motion for a
short time.
Tyre pressure must be checked with tyres rested
and cold. Should it become necessary for whatever
reason to check pressure with warm tyres, do
not reduce pressure even though it is higher than
the prescribed value, but repeat the check when
tyres are cold (see "Wheels" in the "Technical data"
chapter).
The TPMS cannot indicate sudden tyre pressure
drops (for example when a tyre bursts). In this
case, stop the car, braking with caution and avoiding
abrupt steering.
Strong radio-frequency interference could inhibit
the correct operation of the TPMS. This condition
is indicated to the driver by the
warning light
or the symbol lighting up on the instrument panel
together with a message on the display. The
message will disappear automatically as soon as the
interference ceases to affect the system.
The TPMS requires the use of specific equipment.
Contact a Fiat Dealership to find out which
accessories are compatible with the system
(wheels, hub caps, etc.). Using other accessories
may hinder the normal operation of the system.
Given the valve unique specifications, only use
Fiat-approved sealers to repair the tyres. The use of
other sealers may affect the normal operation of
the system.If the vehicle is fitted with TPMS, when a tyre is
removed, it is advisable to replace the rubber
gasket for the valve as well as the ring nut fixing the
sensor. Have this operation performed at a Fiat
Dealership.
If the "punctured tyre" indication persists on the
instrument panel after the initial conditions have
been restored using the Fix&Go Automatic tyre
repair kit, contact a Fiat Dealership.
Changes in outside temperature may cause tyre
pressures to vary. The TPMS may temporarily
indicate insufficient pressure. In this case, check the
tyre pressure when cold and, if necessary, restore
the inflation values.
If the vehicle is fitted with TPMS, tyre and/or rims
fitting/removal operations require specific
precautions. To avoid damaging the sensors or
fitting them incorrectly, tyre and/or rims
fitting/removal operations should be carried out
only by specialists. Contact a Fiat Dealership.
122GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 189 of 299
❒for versions equipped with space-saver wheel,
loosen fastener E fig. 142, take tool box F,
position it near the wheel to be changed and
then take space-saver wheel G;
❒remove hub cap H fig. 143 (versions with steel
rims) or remove the hub cap (versions with
alloy rims);
❒loosen the bolts of the wheel to be replaced by
about one turn with the wrench provided L
fig. 144; if you have alloy rims, rock the car to
make it easier to separate the rim from the
wheel hub;
❒operate device M fig. 145 so as to extend the
jack, until groove N on the upper part of the jack
fits correctly into the lower profile P visible on
the car body next to the indication Q (at approx.
72 cm from the centre of the front wheel or 75
cm from the centre of the rear wheel);❒alert any bystander that the car is about to be
raised; all persons should be kept away from
the car and nobody must touch it until it has
been lowered;
fig. 143
F0Q0393
fig. 144
F0Q0394
fig. 145
F0Q0395
185GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 190 of 299
❒fit handle R fig. 145 to operate the jack and raise
the car until the wheel is a few centimetres
above the ground;
❒fully loosen the fastening bolts and remove the
wheel.
❒make sure the contact surfaces between
space-saver wheel and hub are clean so that the
fastening bolts will not come loose;
❒fit the space-saver wheel aligning the openings S
fig. 146 with the corresponding centering pins T;
❒using the wrench provided, tighten the four
fastening bolts;
❒turn the jack handle R fig. 145 to lower the car
and remove the jack;
❒use the wrench provided to fully tighten the
bolts, passing alternately from one bolt to the
opposite one, as per the numerical sequence
illustrated in fig. 147.REFITTING THE STANDARD WHEEL
Following the procedure described previously, raise
the car and remove the space-saver wheel.
Versions with steel rims
Proceed as follows:
❒make sure the contact surfaces between standard
wheel and hub are clean so that the fastening
bolts will not come loose;
❒fit the standard wheel aligning the openings S
fig. 146 with the corresponding centering pins T;
❒using the wrench provided, tighten the fastening
bolts;
❒lower the car and remove the jack;
❒using the wrench provided, fully tighten the bolts
in the sequence shown in diagram fig. 147;
fig. 146
F0Q0396
fig. 147
F0Q0397
186GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 191 of 299
❒fit the hub cap so that the inflation valve can exit
through the special slot visible on the cap itself;
❒pressure-fit the hub cap starting from the parts
nearest to the inflation valve and continue until
it is completely fitted.
IMPORTANT If it is not fitted properly, the hub cap
may detach itself when the car is running.
Versions with alloy rims
❒tighten centering pin A fig. 148 in one of the
fixing bolt openings on the wheel hub;
❒place the wheel on the pin and tighten the bolts
using the wrench provided. Bolt insertion is
eased by the use of the extension B provided;
❒undo centering pin A and tighten the last
fastening bolt;
❒lower the car and remove the jack;❒using the wrench provided, fully tighten the bolts
in the same sequence shown previously for the
space-saver wheel (see fig. 147);
❒refit the hub cap.
fig. 148
F0Q0217
fig. 149
F0Q0392
187GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGESIN AN
EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 248 of 299
WARNING
The road holding qualities of the car
also depend on the correct inflation
pressure of the tyres.
WARNING
If the pressure is too low the tyre
overheats and can be seriously
damaged.
WARNING
Do not cross switch the tyres, moving
them from the right of the car to the
left and vice versa.
WARNING
Never submit alloy rims to repainting
treatments requiring the use of
temperatures exceeding 150°C.The
mechanical properties of the wheels could be
impaired.
244GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCYSERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 263 of 299
SUSPENSIONVersions Front Rear
1.4 16V - 1.4 T-JET - 1.4 Turbo MultiAir
1.6 MultiJet - 2.0 MultiJetMacPherson independent wheels
with anti-roll barInterconnected wheels with
torsion beamSTEERING SYSTEMVersions TypeTurning circle (kerb to kerb)
(m)
1.4 16V - 1.4 T-JET - 1.4 Turbo MultiAir
1.6 MultiJet - 2.0 MultiJetRack and pinion with electric
power steering10.4 (11.0 with optional 18" alloy
rims)
259GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCETECHNICAL
SPECIFICATIONSINDEX
Page 264 of 299
WHEELSRIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass
tyres. The vehicle registration document also
lists all type-approved tyres.
IMPORTANT If there are any discrepancies
between the Owner Handbook and the registration
document, take the information from the latter.
For safe driving, the car must be fitted with tyres of
the same make and type on all wheels.
IMPORTANT Do not use air chambers with
Tubeless tyres.SPARE WHEEL
Pressed steel rim. Tubeless tyre.
WHEEL GEOMETRY
Front wheel toe-in measured from rim to rim: - 1
mm +/- 1 mm
The values refer to the car in running order.
260GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
Page 267 of 299
RIMS AND TYRES PROVIDED AS STANDARDVersions Rims Tyres Snow tyresSpace-saver wheel (for
versions/markets, where specified)
Rim Tyre
1.4 16V6JX15ET
31.5195/65 R15
91H195/65 R15
91T (M+S)
(°) (°)
7JX16ET31205/55 R16
91H205/55 R16
91T (M+S)
7JX17ET31225/45 R17
91H225/45 R17
91T (M+S)7Jx16ET31
205/55 R16 91H
(**)
(°) On versions equipped with 195/65 R15 and 205/55 R16 tyres, a normal sized tyre may be ordered as an alternative to the Fix&Go.
(**) The 205/55 R16 91H tyre has the same specifications as the space-saver wheel: the information in “Replacing a wheel” paragraph
therefore refers to the 205/55 R16 91H tyre.
263GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCETECHNICAL
SPECIFICATIONSINDEX
Page 268 of 299
Versions Rims Tyres Snow tyresSpace-saver wheel (for
versions/markets, where specified)
Rim Tyre
1.4 T-JET 120 HP -
1.4 Turbo MultiAir6J x 15 ET 31.5195/65 R15
91H195/65 R15
91T (M+S)
(°) (°)
7Jx16ET31205/55 R16
91H205/55 R16
91T (M+S)
7Jx17ET31225/45 R17
91W225/45 R17
91T (M+S)
7Jx16ET31
205/55 R16 91H
(**)
71/2Jx18ET
35225/40 R18
92V
(*)
REINFORCED
225/40 R18
92T (M+S)
(°) On versions equipped with 195/65 R15 and 205/55 R16 tyres, a normal sized tyre may be ordered as an alternative to the Fix&Go.
(**) The 205/55 R16 91H tyre has the same specifications as the space-saver wheel: the information in “Replacing a wheel” paragraph
therefore refers to the 205/55 R16 91H tyre.
(*) Tyres which cannot be fitted with chains.
264GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX