fog light FIAT IDEA 2008 1.G Owners Manual

60
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WINDOW WASHING
WINDSCREEN
WASHER/WIPER
The device can work only when the igni-
tion key is on MAR.
The right lever fig. 74can take five dif-
ferent positions:
Awindscreen wiper off
Bintermittent.
With the lever in position B, turn the
knurled ring Fto select one of four dif-
ferent speeds for the intermittent opera-
tion mode:
,= very slow intermittence
--= slow intermittence
---= mean intermittence
----= fast intermittence
When the automatic light sensor is acti-
vated, the multifunctional display shows
the pre-set sensor sensitivity level. On this
screen it is possible to adjust the sensi-
tivity level using the buttons +and –(see
fig. 73).
Deactivation
The main beam headlights will go out fol-
lowed by the side/tail lights after approx-
imately 10 seconds, when the sensor is de-
activated.
If the beam headlights are enabled (man-
ually by the driver) during automatic light-
ing, the beam lights go off automatically
along with the lights.
IMPORTANT The sensor cannot detect
the presence of fog. So, in foggy condi-
tions, switch the lights on manually.
fig. 73F0H0736m
fig. 74F0H0073m
Ccontinuous slow operation;
Dcontinuous fast operation
Etemporary fast operation (unstable po-
sition).
036-092 idea GB 1 ed 10-07-2008 16:12 Pagina 60

66
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CONTROLS
HAZARD LIGHTS fig. 83-84
Press switch Aregardless of the position
of the ignition key.
The switch will flash with the instrument
panel warning light
Î¥when the device
is on.
Press the switch again to switch the lights
off.
FRONT FOG LIGHTS
(where provided) fig. 85
These are turned on pressing button
5.
They are turned off pressing the button
again or turning the sidelights off.
REAR FOG LIGHTS fig. 86
These are turned on, with the dipped
beam headlights or front fog lights on,
pressing button
4.
They are turned off pressing the button
again or turning off the dipped beam head-
lights or front fog lights.
fig. 83F0H0080m
fig. 84F0H0081m
fig. 85F0H0739m
Use the hazard warning
lights in compliance with lo-
cal regulations.
WARNING
fig. 86F0H0740m
036-092 idea GB 1 ed 10-07-2008 16:12 Pagina 66

123
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
GENERAL WARNINGS ...................................................... 124
LOW BRAKE FLUID LEVEL .............................................. 124
HANDBRAKE ON ............................................................... 124
AIRBAG FAILURE ................................................................. 124
HOT ENGINE COOLANT ................................................ 125
LOW BATTERY CHARGE................................................. 125
LOW ENGINE OIL PRESSURE ......................................... 126
EXHAUSTED OIL ................................................................. 126
“DUALDRIVE” ELECTRIC POWER
STEERING FAILURE............................................................. 126
INCOMPLETE DOOR LOCKING ................................... 126
SEAT BELTS NOT FASTENED ......................................... 126
EBD FAILURE......................................................................... 127
INJECTION SYSTEM FAILURE ......................................... 127
EOBD ENGINE CONTROL SYSTEM FAILURE ........... 127
FRONT PASSENGER AIRBAG DISABLED .................... 128
ABS SYSTEM FAILURE ........................................................ 128
FUEL RESERVE....................................................................... 128
GLOW PLUG HEATING.................................................... 129
GLOW PLUG HEATING FAILURE.................................. 129
WATER IN DIESEL FUEL FILTER ..................................... 129
CAR PROTECTION SYSTEM FAULT - FIAT CODE .. 129
REAR FOG LIGHTS ............................................................. 129
GENERAL FAILURE INDICATION ................................. 130
WW W
A A
R R
N N
I I
N N
G G
L L
I I
G G
H H
T T
S S
A A
N N
D D
M M
E E
S S
S S
A A
G G
E E E
S S
BRAKE PAD WEAR ............................................................. 131
PARTICULATE FILTER CLOGGED................................. 131
SIDE/TAIL LIGHTS AND LOW BEAMS ......................... 131
FOLLOW ME HOME ......................................................... 131
FRONT FOG LIGHTS ......................................................... 131
LEFT-HAND DIRECTION INDICATOR ....................... 132
RIGHT-HAND DIRECTION INDICATOR ................... 132
“DUALDRIVE” ELECTRIC POWER STEERING
ACTIVATION ........................................................................ 132
CRUISE CONTROL SYSTEM ............................................ 132
MAIN BEAMS ......................................................................... 132
POSSIBLE ICE ON ROAD.................................................. 132
LIMITED RANGE .................................................................. 132
123-132 idea GB 1 ed 10-07-2008 8:29 Pagina 123

129
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
GLOW PLUG
HEATING
(Multijet versions - amber)
GLOW PLUG HEATING
FAILURE (Multijet versions -
amber)
Glow plug heating
The warning light goes on when the key is
turned to MAR. It goes out as soon as the
glow plugs have reached the preset tem-
perature. Start the engine as soon as the
warning light goes out.
IMPORTANT At high ambient tempera-
tures the warning light stays on for an ex-
tremely short time.
Glow plug heating failure
The warning light flashes in the event of
a failure in the glow plug heating system.
Go to a Fiat Dealership as soon as possi-
ble.
The display will show the dedicated mes-
sage.
m
WATER IN DIESEL
FUEL FILTER
(Multijet versions - amber)
When the ignition key is moved
to MAR, the warning light turns on and
should go off after a few seconds.
The warning light c turns on when there
is water in the diesel fuel filter.
The display will show the dedicated mes-
sage.
c
CAR PROTECTION
SYSTEM FAULT - FIAT
CODE (amber)
Turning the key to MAR, the
warning light flashes once and then goes
off.
If the warning light stays on with the igni-
tion key positioned on MAR, a failure may
have occurred (see “Fiat Code system” in
section “Dashboard and controls”).
IMPORTANT Simultaneous turning on of
the warning lights
Uand Yindicates a
failure in the Fiat CODE system.
If the warning light
Yflashes with the en-
gine running, the car is not protected by
the engine inhibitor device (see “Fiat Code
system” in section “Dashboard and con-
trols”).
Contact Fiat Dealership to have all the
keys stored.
Y
REAR FOG LIGHTS
(amber)
The warning light comes on
when the fog lights are turned
on.
4
The presence of water in the
supply circuit may cause se-
vere damage to the injection
system and irregular engine
operation. If the warning light c goes
on (with the message on the display on
some versions), go to a Fiat Dealership
as soon as possible to remove clogging
from the system. Whenever the warn-
ing light comes on immediately after
refuelling, water may have been intro-
duced in the tank. In this case, stop the
engine immediately and contact a Fiat
Dealership.
123-132 idea GB 1 ed 10-07-2008 8:29 Pagina 129

130
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
GENERAL FAILURE
INDICATION
(amber)
The warning light turns on in the
following circumstances.
External light failure
The warning light comes on (on some ver-
sions only) when a failure is detected in
one of the following lights:
– tail lights
– stop lights (excluding 3rd stop)
– rear fog lights
– direction indicators
– plate lights.
The fault identified in the lights above may
be due to: one or more burnt lamps, a
blown protection fuse or interruption of
the electrical connection.
The display will show the dedicated mes-
sage.
è
Fresh air filter clogged
(where provided)
The warning light turns on when the par-
ticulate filter is clogged and the driving
conditions do not enable automatic acti-
vation of the regeneration procedure.
To allow the regeneration procedure,
keep the car running until the warning light
turns off.
The display will show the dedicated mes-
sage.
Engine oil pressure sensor failure
The warning light turns on when a failure
is detected in the engine oil pressure sen-
sor. Go to a Fiat Dealership as soon as
possible.Twilight/rain sensor failure
The warning light turns on when a failure
is detected in the twilight/rain sensors. Go
to a Fiat Dealership as soon as possible.
The display will show the dedicated mes-
sage.
Fuel cut-off switch tripped
The warning light comes on when the fu-
el cut-off switch trips.
The display will show the dedicated mes-
sage.
Speed limit exceeded
The display shows the dedicated message
when the car exceeds the set speed limit
(see “Multifunction Display” in section
“Dashboard and controls”).
123-132 idea GB 1 ed 10-07-2008 8:29 Pagina 130

131
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
BRAKE PAD WEAR
(amber)
The warning light goes on if the
front brake pads are worn. In this
case replace them as soon as possible.
The display will show the dedicated mes-
sage.
d
PARTICULATE FILTER
CLOGGED
(1.3 Multijet
90 HP version) (amber)
When the ignition key is moved to MAR,
the warning light turns on and should go
off after a few seconds.
The warning light turns on when the par-
ticulate filter is clogged and the driving
conditions do not enable automatic acti-
vation of the regeneration procedure.
To allow the regeneration procedure,
keep the car running until the warning light
turns off.
The display will show the dedicated mes-
sage.
h
SIDE/TAIL LIGHTS
AND LOW BEAMS
(green)
FOLLOW ME HOME (green)
Side/tail lights and low beams
The warning light comes on when side/tail
lights or low beams are turned on.
Follow me home
The warning light turns on when this de-
vice is active (see “Follow me home” in
section “Dashboard and controls”).
The display will show the dedicated mes-
sage.
3
FRONT FOG
LIGHTS (green)
The warning light comes on
when the front fog lights are
turned on.
5
123-132 idea GB 1 ed 10-07-2008 8:29 Pagina 131

146
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
Bulb Ref. Figure Type Power
Main beam headlightsEH1 55W
Dipped beam headlights DH7 55W
Front side lights AW5W 5W
Front fog lights (where provided)EH1 55W
Front direction indicators BPY21W 21W
Side direction indicators AWY5W 5W
Rear direction indicators BPY21W 21W
Taillights BP21/5W 21W/5W
Brake lights BP21/5W 21W/5W
Third brake light (additional brake lights) AW5W 5W
Reversing light BP21W 21W
Rear fog lights BP21W 21W
Number plate lights CC5W 5W
Front ceiling lightAW5W 10W
Rear ceiling lightAW5W 10W
Rear ceiling lights (with sunroof)AW5W 5W
Boot light AW5W 5W
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 146

147
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
FRONT LIGHT UNITS
The front light units contain the sidelights,
the dipped beam, main beam, direction in-
dicator and fog light bulbs.
To change the bulbs of the sidelights, low
beams, direction indicators and fog lights
it is necessary to remove the cover A-
fig. 18releasing the catch B.
fig. 18F0H0179mfig. 19F0H0180m
The bulbs are arranged inside the light unit
fig. 19 as follows:
G: direction indicators
F: main beam headlights
E: sidelights
D: fog lights
C: dipped beam headlights
After replacement, refit the covers cor-
rectly checking that they are properly se-
cured.MAIN BEAM HEADLIGHTS
To change the bulb, proceed as follows:
❒turn the cap A-fig. 20anticlockwise
and remove it;
❒disconnect the electrical connector B-
fig. 21;
❒release the bulb catch C-fig. 21;
❒remove the bulb D-fig. 21and change
it;
❒refit the catch C-fig. 21, connect the
electrical connector Band fit the cap
A-fig. 20turning it clockwise. Put the
cap ventilation outlet H-fig. 20from
the top downwards.
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 147

149
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
Side
To change the bulb, proceed as follows:
❒lever in the point shown by the arrow
to compress the catch and remove the
unit C-fig. 24;
❒turn the bulb holder Dcounter-clock-
wise, remove the snap-fitted bulb and
change it;
❒refit the bulb holder Din the trans-
parent cover, then position the unit
making sure the catch clicks into place.
fig. 24F0H0184m
FRONT SIDELIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing
the relevant catch;
❒remove the snap-fitted bulb holder A-
fig. 25, extract the bulb Band change
it;
❒refit the bulb holder A;
❒refit the protective cover correctly.FRONT FOG LIGHTS
(where provided)
To change the bulb, proceed as follows:
❒disconnect the electrical connector C-
fig. 26;
❒release the bulb catch D;
❒remove the bulb Eand change it;
❒fit the new bulb, hook the bulb catch
Dand re-connect the electrical con-
nector C.
fig. 25F0H0185mfig. 26F0H0186m
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 149

151
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
The bulbs are arranged inside the light unit
as follows:
D: sidelights / STOP
E: direction indicators
F: reversing light
G: rear fog lights
fig. 29F0H0189mfig. 30F0H0190m
ADDITIONAL BRAKING LIGHT
(THIRD STOP)
To change the bulbs, proceed as follows:
❒open the tailgate;
❒slacken the two fastening screws A-
fig. 30;
❒press the catch Band remove the bulb
holder;
❒remove the snap-fitted bulbs and
change them;
❒insert the bulb holder making sure the
catch Bclicks into place; drive in the
two fastening screws A.
IMPORTANT Where provided, on ver-
sions with dark windows, replace the
whole light unit since it is sealed.Number plate light
To change the bulb, proceed as follows:
❒work in the point shown by the arrow
and remove the transparent A-fig. 31;
❒change the bulb Breleasing it from the
side contacts and making sure the new
bulb is correctly fastened between the
contacts;
❒refit the transparent.
fig. 31F0H0192m
133-160 idea GB 1 ed 10-07-2008 8:30 Pagina 151