clock HONDA CIVIC 2004 7.G Owners Manual

Your Vehicle at a Glance
3
WINDSHIELD WIPERS/WASHERSHAZARD WARNING LIGHTS
CRUISE CONTROL SWITCHES
TILT ADJUSTMENT
MIRROR CONTROLS
MOONROOF
HEADLIGHTS/TURN SIGNALS
REAR WINDOW
DEFOGGER
CRUISE CONTROL
MASTER SWITCH AUDIO SYSTEM
DIGITAL CLOCK
(P. 63)
(P. 80)
(P. 107)
(P. 81) (P. 66)(P. 107)(P. 65)
(P. 92)
(P. 106)
(P. 65)
(P. 62)
 — — y

 y
( y   y

AT model is shown.
Control L ocations
Inst rument s and Cont rols50
HEATING/COOLING CONTROLS
FUEL FILL DOOR RELEASE
TRUNK RELEASE CRUISE CONTROL SWITCHES
CRUISE CONTROL
MASTER SWITCH
POWER DOOR LOCK
SWITCH
MIRROR
CONTROLS
HOOD RELEASE
HANDLE
POWER WINDOW
SWITCHES MOONROOF
CONTROLS
(P. 70) (P. 80)
(P. 107)
(P. 78) (P. 81)
(P. 113) (P. 71) (P. 114)(P. 107) AUDIO SYSTEM
(P. 92)
(P. 106)
DIGITAL CLOCK
(P. 88)
 — — y
  y
( y  y

´
Ü
Õ
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR2025 To replace the battery, move the
round cover on the back of the
transmitter by turning it
counterclockwise with a coin. Insert
a new battery with the side facing
up. Align the mark on the cover
with the mark on the
transmitter. Set the cover in place
andturnitclockwise.
As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, including
interf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f or
compliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not cause
interf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Remote Transmitter
Inst rument s and Cont rols
Replacing the Transmitter
Battery
73
ROUND
COVER
CUSHION RING
BATTERY
 — — y

y
( y  y

When storing cargo, you can move
therearcentershoulderbeltoutof
the way by removing the belt f rom
the guide.
The left and right halves can be
f olded separately f rom inside the
vehicle or inside the trunk. To f old
down the seat-back f rom inside the
vehicle, insert the master key in the
lock on the rear shelf . To f old down
the driver’s side, turn the key
clockwise, pull down the top of the
seat-back, then release the key. To
f old down the passenger’s side, turn
the key counter clockwise and
perf orm the same procedure.
The lid of the console compartment
canbeusedasanarmrest.
Make sure the passenger’s hands or
fingersareawayfromthearmrest
bef ore pushing it down.
It is optional on other models.
Standard on LX and EX models in the
U.S., and DX-G, LX and Si models in
Canada
Seats
Inst rument s and Cont rols
Armrest Folding Rear Seat
76
MASTER KEY GUIDE
CENTER SHOULDER BELT
 — — y
y
( y  y

Î
ÎThe heating and air conditioning
systems in your Honda provide a
comf ortable driving environment in
all weather conditions.
The standard audio system has
many f eatures. This section de-
scribes those f eatures and how to
use them. (If you selected an
optional audio system, ref er to the
operating instructions that came
with it.) ...............
Vents, Heating, and A/C . 88
.........................
Air Flow Buttons . 89
............................
Playing the Radio . 92
..............................
Radio Reception . 95
....................................
Playing a CD . 97
.....................................
CD Changer . 98
......................
Protecting Your CDs . 99
.........
CD Player Error Messages . 100
.....
CD Changer Error Messages . 101
...............................
Playing a Tape . 102
.................
Radio Thef t Protection . 105
..........................
Setting the Clock . 106
...............................
Cruise Control . 107
Your Honda has an anti-thef t audio
system that requires a code number
to enable it. Air conditioning is optional on DX
model. It is standard on other models.
LXandEXmodelsintheU.S.,andLX
andSimodelsinCanada
Comf ort and Convenience Features
Comf ort and Convenience Feat ures87
 — — y

y
( y   y

Turning this dial clockwise increases
the temperature of the airflow.
This button turns the air
conditioning on and of f . The light in
thebuttonisonwhentheA/Cison.The outside air intakes f or the
heating and cooling system are at
the base of the windshield. Keep this
area clear of leaves and other debris.
ThesystemshouldbeleftinFresh
Air mode under almost all conditions.
Keeping the system in Recirculation
mode, particularly with the A/C of f ,
can cause the windows to fog up.
Switch to Recirculation mode when
driving through dusty or smoky
conditions, then return to Fresh Air
mode.
This button turns the rear window
def ogger of f and on (see page ).
Use the mode control dial to select
the vents the air flow from. Some air
will f low f rom the dashboard vents in
all modes. Air flows from the center
and corner vents in the dashboard.
Air f low is divided between
the vents in the dashboard and the
f loor vents.
Air f lows f rom the f loor
vents. When you select , the
system automatically switches to
Fresh Air mode.
Air f low is divided between
the f loor vents and the def roster
vents at the base of the windshield.
Air f lows f rom the def roster
vents at the base of the windshield.
When you select or ,
the system automatically switches to
Fresh Air mode and turns on the
A/C.
When the light in the button is on,
air f rom the car’s interior is sent
throughout the system again. When
the light is of f , air is brought in f rom
the outside of the vehicle (Fresh Air
mode).
Turn this dial to control fan speed
and the air flow.
65
Optional on DX models
Air Flow Buttons
Comf ort and Convenience Feat ures
Fan Control Dial
T emperature Control Dial
Air Conditioning (A/C) Button
Recirculation ButtonRear Window Def ogger Button
Mode Control Dial
89
 — — y
y
( y  y

If your vehicle’s battery is
disconnected or goes dead, you will
need to set the clock.You can quickly set the time to the
nearest hour. If the displayed time is
bef ore the half hour, press and hold
the CLOCK button until you hear a
beep (Except DX Model only), then
press the R button to set the clock
back to the previous hour. If the
displayed time is af ter the half hour,
the clock sets forward to the
beginning of the next hour.
For example: 1:06 will reset to 1:00
1:52 will reset to 2:00
Adjust the minutes by pressing and
holding the CLOCK button, then pressing the M button.
Adjust the hours by pressing and
holding the CLOCK button, then
pressing the H button.
You can set the time only when the
clock is displayed.
Press and hold the CLOCK button
until you hear a beep, then release
the button. Change the hours by
pressing the H button until the
numbers advance to the desired time.
Change the minutes by pressing the
M button until the numbers advance
to the desired time. When you are
f inished, press the CLOCK button.
DX Model
Except DX Model
Setting the Clock
Comf ort and Convenience Feat ures106
M BUTTON
H BUTTON
R BUTTON
H BUTTON CLOCK (SCAN/RPT) BUTTON
R BUTTON
M BUTTON
DX Model
CLOCK BUTTONU.S.: LX, EX,
Canada: LX, Si Models
 — — y
  
y
( y 
 y

When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spill immediately; it could
damage components in the engine
compartment.
Put the radiator cap back on and
tighten it.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components. Check the f luid level in the
windshield washer reservoir at least
monthly during normal use.
The low washer
level indicator will light when the
level is low.
Fill the reservoir with a good-quality
windshield washer f luid. This
increases the cleaning capability and
prevents f reezing in cold weather.
When you ref ill the reservoir, clean
the edges of the windshield wiper
blades with windshield washer f luid
on a clean cloth. This will help to
condition them.
2. 3. 4. 5.
1.
On Canadian models:
Engine Coolant, Windshield Washers
Maint enance
Windshield Washers
148
NOTICE:
RADIATOR CAP
Do not use engine antif reeze
or a vinegar/water solution in the
windshield washer reservoir. Antif reeze
can damage your vehicle’s paint, while
a vinegar/water solution can damage
the windshield washer pump. Use only
commercially-available windshield
washer f luid.
 — — y

y
( y 

y

If you change the low beam
headlight bulb on the driver’s side,
you also need to remove the upper
part of the windshield washer
reservoir tank. Use a f lat-tipped
screwdriver to remove the holding
clip, then remove the upper part by
pulling it straight up.If you need to change a headlight
bulb on the passenger’s side, remove
the bolt from the stay and push the
battery toward windshield to obtain
enough working space.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
2. 3.
Lights
Maint enance154
HOLDING CLIP BOLT
STAYTAB
 — — y

y
( y 
y

Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the headlights to test the
new bulb.
(Passenger’s side)
Put the battery back to its original
position, reinstall the bolt in the
stay and tighten it securely.
If you removed the upper part of
the windshield reservoir, put it
back in place. Install the holding
clip. Lock it in place by pushing on
the center.
Reinstall the power steering
reservoir.
(Driver’s side)
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
inner f ender, and pull the inner
f ender cover back.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
If you are changing the bulb on
the driver’s side, start the engine,
turn the steering wheel all the way
to the right, and turn off the
engine. If you are changing the
bulb on the passenger’s side, turn
the steering wheel to the left.
Insert the new bulb into the hole
and turn it one-quarter turn clock-
wise to lock it in place.
2.
4. 5.6.
1.3.
7.
Lights
Maint enance
Replacing the Front Side Marker/
Turn Signal and Parking L ightBulb
155
HOLDING CLIP
 — — y
y
( y 
y