mirror lexus LS400 1994 Electrical Components / 1994 LS400: COMFORT ADJUSTMENT
[x] Cancel search | Manufacturer: LEXUS, Model Year: 1994, Model line: LS400, Model: Lexus LS400 1994Pages: 34, PDF Size: 12.11 MB
Page 1 of 34
SECTION 1 – 6
49
INSTRUMENTS AND CONTROLS
Comfort adjustment
Front seat50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Headrests52 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tilt and telescopic steering wheel54 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outside rear view mirrors57 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inside rear view mirror58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Seat belts59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplemental restraint system (SRS)67 . . . . . . . . . . . . . . . . . . . . . . . .
Child restraint73 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driving position memory system81 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 9 of 34
COMFORT ADJUSTMENT
57
OUTSIDE REAR VIEW MIRRORS
Adjust the mirror so you can just see the side of your
vehicle in the mirror.
Be careful when judging the size or distance of any object seen
in the outside rear view mirror on the passenger’s side. It is a
convex mirror with a curved surface. Any object seen in a
convex mirror will look smaller and farther away than if seen in
a normal flat mirror.
Power rear view mirror control
Control switch
Master switch
To adjust the power rear view mirror, first place the master
switch at “R” (right) or “L” (left), and push the control
switch on the desired side.
If the engine is not running, the key must be in the “ACC”
position for operation of the power rear view mirror.
NOTICE:
If ice should jam the mirror, do not operate the control or
scrape the mirror face. Use a spray de-icer to free the
mirror.
Page 10 of 34
COMFORT ADJUSTMENT
58
Folding rear view mirrors
To fold the rear view mirror, push backward.
The rear view mirrors can be folded backward for parking in
restricted areas.
INSIDE REAR VIEW MIRROR
The mirror surface is normal when switched to DAY, and
appears slightly darker when switched to NIGHT as its
reflectivity is reduced.
While driving at night, switching the inside rear view
mirror to NIGHT by pushing the button can reduce the
reflection of the headlights of following vehicles
When the ignition key is inserted or removed, the mirror is
always in DAY mode.
Each time the button is pushed, the mode is switched between
DAY and NIGHT.
Adjust it before driving so that the rear view is the best.
When the outside air temperature is low, switching between
DAY and NIGHT may be a little slower.
Page 33 of 34
COMFORT ADJUSTMENT
81
DRIVING POSITION MEMORY
SYSTEM
The micro computer can memorize the position of the driver’s
seat, the height of the shoulder belt anchor of the driver’s seat
belt, and the positions of the tilt and telescopic steering, and
outside rear view mirrors. Two different driving position profiles
can be entered into the computer’s memory.
Recording a driving position in the computer’s memory can
only be done when the ignition key is in the “ON” position and
the shift lever is in the “P” position.
Setting a driving position
1. Adjust the driver’s seat, driver’s shoulder belt anchor,
tilt and telescopic steering and outside rear view mirrors
to the desired position.2. While pushing the “SET” button, push button “1” or “2”
until the signal beeps.
The beep sound means that the positions are recorded in the
computer’s memory.
By repeating these two steps and pressing the remaining
button, the driving position for another driver can be recorded.
To set a new memorized position, select the desired position
and perform step 2. The previous memory will be erased and
the new position will be set.
To make only slight changes to an already memorized position,
the easiest way is to first activate the memorized position, then
make the desired changes and perform step 2 above.