start stop button MERCEDES-BENZ SL550 2007 R230 Owner's Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: SL550, Model: MERCEDES-BENZ SL550 2007 R230Pages: 473
Page 197 of 473
196 Controls in detailPower windowsOpening and closing the windows
The windows are opened and closed elec-
trically. The switches for all the windows
are on the driver’s door. The switch for the
passenger side windows is on the passen-
ger door.
1Left door and rear side windows
2Right door and rear side windows
Switch on the ignition (
page 39).
Warning!
G
When closing the windows, make sure that
there is no danger of anyone being injured
by the closing procedure.
The closing of the door windows can be im-
mediately halted by releasing the switch or,
if the switch was pulled past the resistance
point and released, by either pressing or
pulling the respective switch.
The closing of the rear side windows can be
immediately halted by releasing the switch.
If a door window encounters an obstruction
that blocks its path in a circumstance where
you pulled the switch past the resistance
point and released it to close the door win-
dow, the automatic reversal function will
stop the door window and open it slightly.
If the door window encounters an obstruc-
tion that blocks its path in a circumstance
where you are closing the door window by
pulling and holding the switch, by pressing
and holding button ‹on the SmartKey,
by pressing and holding the lock button (ve-
hicles with KEYLESS-GO*) on an outside
door handle, by pressing and holding the re-
tractable hardtop switch, or by pressing and
holding button,on the climate control
panel, the automatic reversal function will
not operate.
When leaving the vehicle, always remove the
SmartKey or the SmartKey with
KEYLESS-GO* from the starter switch, take
it with you, and lock the vehicle. Do not
leave children unattended in the vehicle, or
with access to an unlocked vehicle. Unsu-
pervised use of vehicle equipment can
cause an accident and/or serious personal
injury.i
Depending on the current position, the win-
dows may also open or close when the air recir-
culation button, on the control panel of the
automatic climate control (
page 191) is
pressed and held.
i
After switching off the ignition (
page 39)
or removing the SmartKey from the starter
switch, the windows can be operated
until you open a door
for at least 5 minutes if no door was opened
Page 264 of 473
263 Operation
Driving instructions
Parking
Tires
Treadwear indicators (TWI) are required by
law. These indicators are located in six
places on the tread circumference and be-
come visible at a tread depth of approxi-
mately
1/16
in (1.6 mm), at which point
the tire is considered worn and should be
replaced.
Warning!
G
Do not park this vehicle in areas where com-
bustible materials such as grass, hay or
leaves can come into contact with the hot
exhaust system, as these materials could be
ignited and cause a vehicle fire.
To reduce the risk of personal injury as a re-
sult of vehicle movement, before
turning off
the engine and leaving the vehicle always:
Keep right foot on brake pedal.
Firmly depress parking brake pedal.
Move the gear selector lever to
positionP.
Slowly release brake pedal.
When parked on an incline, turn front
wheels towards the road curb.
Turn the SmartKey in the starter switch
to position0 and remove the SmartKey
from the starter switch, or press the
start/stop button (vehicles with
KEYLESS-GO*).
Take the SmartKey or the SmartKey with
KEYLESS-GO* and lock vehicle when
leaving.
!
Set the parking brake whenever parking or
leaving the vehicle. In addition, move gear selec-
tor lever to positionP. When parking on hills,
turn front wheels towards the road curb.
Warning!
G
If you feel a sudden significant vibration or
ride disturbance, or you suspect that possi-
ble damage to your vehicle has occurred,
you should turn on the hazard warning flash-
ers, carefully slow down, and drive with cau-
tion to an area which is a safe distance from
the road.
Inspect the tires and the vehicle underbody
for possible damage. If the vehicle or tires
appear unsafe, have the vehicle towed to
the nearest Mercedes-Benz Center or tire
dealer for repairs.
Page 272 of 473
271 Operation
At the gas station
At the gas station
RefuelingThe fuel filler flap is located on the
right-hand side of the vehicle towards the
rear. Locking/unlocking the vehicle with
the SmartKey or the SmartKey with
KEYLESS-GO* automatically locks/un-
locks the fuel filler flap.
1Fuel filler flap
2Fuel filler cap
3Holder
Turn off the engine
by turning the SmartKey to
position0. Remove the SmartKey
from the starter switch.
by pressing the KEYLESS-GO*
start/stop button. Open the driv-
er’s door (with the driver’s door
open, starter switch is in position 0,
same as SmartKey removed from
starter switch).
Open fuel filler flap 1 by pushing at
the point indicated by the arrow.
The fuel filler flap springs open.
Turn fuel cap 2 counterclockwise and
hold on to it until possible pressure is
released.
Take off fuel cap 2 and place it into
holder 3 located on the inside of the
fuel filler flap.
Only fill your tank until the filler nozzle
unit cuts out – do not top up or over-
fill.
Warning!
G
Gasoline is highly flammable and poisonous.
It burns violently and can cause serious
injury. Whenever you are around gasoline,
avoid inhaling fumes and skin contact,
extinguish all smoking materials. Never
allow sparks, flame or smoking materials
near gasoline!
Turn off the engine before refueling.Warning!
G
Overfilling of the fuel tank may create pres-
sure in the system which could cause a gas
discharge. This could cause the gas to spray
back out when removing the fuel pump noz-
zle, which could cause personal injury.
Page 278 of 473
277 Operation
Engine compartment
If necessary, add engine oil.
For information on adding engine oil, see
(
page 278).
For more information on engine oil, see the
“Technical data” section (
page 444) and
(
page 446).
Other display messages
If the SmartKey or the KEYLESS-GO*
start/stop button is not in position2, the
following message will appear:
Turn ignition on to
measure engine
oil level
Switch on the ignition (
page 39).If you see the message:
Observe
waiting time
If the engine is at operating tempera-
ture, wait 5 minutes before repeating
the check procedure.
If the engine is not at operating temper-
ature yet, wait 30 minutes before re-
peating the check procedure.
If you see the message:
Engine oil level
Not when
engine on
Turn off the engine.
If the engine is at operating tempera-
ture, wait 5 minutes before checking
oil.
If the engine is at operating tempera-
ture yet, you must wait 30 minutes be-
fore checking oil.If there is excess engine oil with the engine
at normal operating temperature, the
following message will appear:
Engine oil level
Reduce
oil level
Have excess oil siphoned or drained
off. Contact an authorized
Mercedes-Benz Center.
For more information on messages in the
display concerning engine oil, see the
“Practical hints” section (
page 375).
!
Excess oil must be siphoned or drained off.
It could cause damage to the engine and catalyt-
ic converter not covered by the Mercedes-Benz
Limited Warranty.
Page 328 of 473
327 Operation
Vehicle care
Fold the wiper arms forward until they
snap into place.
Clean the wiper blade inserts with a
clean cloth and detergent solution.
Use a soft, clean cloth and a mild win-
dow cleaning solution on all outside
and inside glass surfaces.
An automotive glass cleaner is recom-
mended.Rear window cleaning
Clean the rear window with the hardtop
fully raised and closed.
Use a soft, clean cloth and a mild win-
dow cleaning solution on all outside
and inside glass surfaces.
An automotive glass cleaner is recom-
mended.
Warning!
G
For safety reasons, switch off wipers and re-
move SmartKey from starter switch (vehi-
cles with KEYLESS-GO*: Make sure the
vehicle’s on-board electronics have
status0.) before cleaning the windshield
and/or the wiper blades. Otherwise, the
wiper motor could suddenly turn on and
cause injury.!
Do not pull on the wiper blade inserts. They
could tear.
!
Fold the windshield wiper arms back onto
the windshield before turning the SmartKey in
the starter switch or pressing the KEYLESS-GO
start/stop button (vehicles with KEYLESS-GO*).
Hold on to the wiper when folding the wiper arm
back. If released, the force of the impact from
the tensioning spring could crack the windshield.
!
To clean the window interior, do not use a
dry cloth, abrasives, solvents or cleaners con-
taining solvents. Do not touch the inside of the
front, rear or side windows with hard objects
such as an ice scraper or ring. Doing so may
damage the windows.
Warning!
G
Do not clean the rear window with the hard-
top in a position other than the fully raised
and closed position. Otherwise, the hardtop
may move unexpectedly which may result in
personal injury to you or others.
Page 361 of 473
360 Practical hintsWhat to do if …Left display
Right display
Possible cause/consequence
Possible solution
P
Gear selector
lever to P
You have tried to start the engine with
the KEYLESS-GO* start/stop button
with the gear selector lever not in posi-
tion P.
Place the gear selector lever in position P.
You have tried to turn off the engine
with the KEYLESS-GO* start/stop but-
ton with the gear selector lever not in
position P.
Retractable roof
open/close
completely
The retractable hardtop is not locked
properly.
Push or pull on the retractable hardtop
switch until the indicator lamp in the
switch goes out and the retractable hard-
top is completely open or closed
(page 199).
Page 380 of 473
379 Practical hints
What to do if …
Left display
Right display
Possible cause/consequence
Possible solution
F
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized while the engine is
running because:
The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.
There is strong radio-frequency
interference.
Stop the vehicle in a safe location or as soon
as it is safe to do so.
Search for the SmartKey with KEYLESS-GO*.
Otherwise the vehicle cannot be centrally
locked nor can the engine be started again af-
ter the engine is stopped.
Operate the vehicle with the SmartKey with
KEYLESS-GO* in the starter switch
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized when attempting to
start the engine with the
KEYLESS-GO start/stop button* on
the gear selector lever because:
The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.
The battery in the SmartKey
with KEYLESS-GO* is not insert-
ed properly or completely dis-
charged.
Change the position of the SmartKey with
KEYLESS-GO* in the vehicle.
Make sure the batteries in the SmartKey with
KEYLESS-GO* are properly inserted
(page 395) and are not discharged
(page 110).
Start the engine with the SmartKey with
KEYLESS-GO* in the starter switch if
necessary.
Page 394 of 473
393 Practical hints
Locking/unlocking in an emergency
Locking the vehicle
If you cannot lock the vehicle with the
SmartKey, lock it with the mechanical key
as follows:
Close the passenger door and the
trunk.
Press the central locking switch in the
center console (
page 119).
Check whether the locking knob on the
passenger door has moved down.
If necessary push it down manually.
Remove the mechanical key from of
the SmartKey (
page 391).
Check whether the trunk is locked.
If necessary, lock the trunk with the
mechanical key (
page 117).
Except for the driver’s door, the vehicle
should now be locked.1Locking
2Mechanical key
Insert mechanical key 2 (
page 391)
into the driver’s door lock until it stops.
Turn mechanical key 2 clockwise to
position 1.
The driver’s door is locked.
i
Unlocking the glove box with the mechanical
key will trigger the anti-theft alarm system. To
cancel the alarm, do one of the following:
Press button Œ or ‹ on the
SmartKey.
Insert the SmartKey in the starter switch.
Press the KEYLESS-GO* start/stop button
(page 40).
Grasp an outside door handle (vehicles with
KEYLESS-GO* only).
i
This procedure does not arm the anti-theft
alarm system, nor does it lock the fuel filler flap
and the storage compartments.
The storage compartments can be locked
separately (
page 235).
Page 412 of 473
411 Practical hints
Flat tire
Turn the SmartKey in the starter switch
to position1.
or
Press the KEYLESS-GO* start/stop
button on the gear selector lever once
without depressing the brake pedal.
PressI on the electric air pump
switch2.
The electric air pump should now
switch on and inflate the tire.
Inflate the spare tire:
SL 550 to 36 psi (2.5 bar)
SL 600, SL 55 AMG, SL 55 AMG
(Performance Package*), and
SL 65 AMG to 51 psi (3.5 bar)
This takes about 5 minutes.
Air hose4 and union nut5 can be-
come hot during inflation. Exercise
proper caution to avoid burning your-
self when using the equipment.
Press0 on the electric air pump
switch2.
Turn the SmartKey in the starter switch
to position0.
or
Press KEYLESS-GO* start/stop button
on the gear selector lever twice without
depressing the brake pedal.
The electric air pump should now be
switched off.
If the spare tire inflation pressure is
above the recommended tire inflation
pressure for the respective collapsible
tire (
page 440), release excess spare
tire inflation pressure using the vent
screw.
Detach the electric air pump.
Stow the electrical plug and the air
hose behind the flap and place the air
pump back in the trunk.
!
Compare the recommended tire inflation
pressure for your vehicle with the tire inflation
pressure on the yellow label located on the spare
wheel rim.
If the tire inflation pressure on the yellow label
on the spare wheel rim differs from the values
given in this Operator’s Manual, inflate the tire to
the recommended tire inflation pressure given
on the yellow label on the spare wheel rim.
!
Do not operate the electric air pump longer
than 8 minutes without interruption. Otherwise it
may overheat.
You may operate the air pump again after it has
cooled off.
Warning!
G
Follow recommend inflation pressures.
Do not overinflate tires. Overinflating tires
can result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes,
etc.
Do not underinflate tires. Underinflated tires
wear unevenly, adversely affect handling
and fuel economy, and are more likely to fail
from being overheated.
Page 417 of 473
416 Practical hintsBatteries
Disconnecting the batteries
Apply the parking brake (
page 61).
Make sure the gear selector lever is set
to position P (
page 168).
Close the retractable hardtop
(page 199).
Turn off all electrical consumers.
Turn off the engine (
page 62).
Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*: Open
the driver’s door.
Open the trunk.
Read and observe safety instructions
and precautions (
page 281).
Open the luggage cover in the trunk
(page 206).
Remove the trunk floor.
The battery for electrical consumers is
located in the right hand area of the
trunk (
page 388).
Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal5 of the consumer battery
(page 414).
Warning!
G
With a disconnected battery
you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect
the gear selector lever will remain
locked in positionP
!
Always disconnect the batteries in the order
described below, even if you only want to charge
the starter battery, for example. Otherwise the
vehicle’s electronics can be damaged.