turn signal bulb MITSUBISHI SHOGUN 2003 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2003, Model line: SHOGUN, Model: MITSUBISHI SHOGUN 2003Pages: 392, PDF Size: 14.34 MB
Page 101 of 392
Turn-signal indication lamps - green
ED52A-BB
These indication lamps blink on and off when a
turn-signal lamp is operating.NOTE
If the blinking is too fast, the cause may be a faulty
turn-signal connection or a blown lamp bulb.Hazard warning indication lamps - green
ED30A-A
When the hazard warning lamp switch is pressed,
all turn-signal lamps will flash on and off continu-
ously.Engine oil level warning lamp-amber
ED26A-D
This lamp illuminates when the ignition switch is
turned to the “ON” position, and goes off after theengine has started. If it lights up while the engine is
running, the oil level is too low.
If the warning lamp lights while the engine is run-
ning, stop the engine and add engine oil to speci-
fied level. (Refer to “Engine oil” on page 9-2.)
Low fuel indication lamp - amber
ED63ABD
The indication lamp comes on when the fuel tank is
getting low. Refuel as soon as possible.
CAUTION
On petrol-powered vehicles, do not drive with
an extremely low fuel level; running out of fuel
could cause damage to the catalytic con-
verter.
NOTE
On inclines or curves, due to the movement of fuel
in the tank, the low fuel indication lamp may come
on earlier than usual.
Instruments and controls
4-9
Div:
Out put date:
Page 108 of 392
NOTE
If the lamp flashes unusually quickly, the
bulb in a turn-signal lamp may have burned
out. Have the vehicle inspected by an
authorized MITSUBISHI dealer.
E01G050A
LHDHeadlamp levelling switch
EE01GIOc
The angle of the headlamp beam varies
depending upon the load carried by the
vehicle.
The headlamp levelling switch can be used
to adjust the headlamp illumination dis-
tance (when the lower beam is illuminated)
so that the headlamps’glare does not dis-
tract the drivers of approaching vehicles.
Set the switch (referring to the following
table) to the appropriate position accord-
ing to the number of people and the load
in the vehicle.
E01G060A
RHD
Instruments and controls
4-16Div:
Out put date:
Page 332 of 392
N29C001A
6. Insert a new fuse of the same capac-
ity by using the fuse puller and insert the
fuse at the same place in the fuse box.
CAUTION
(1) If the newly inserted fuse blows
again after a short time, have the
electric system checked by an
authorized MITSUBISHI dealer to
find the cause and rectify it.
(2) Never use a fuse with a capac-
ity larger than that specified or
any substitute, such as wire, foil,
etc.; doing so will cause the cir-
cuit wiring to heat up and could
cause a fire.
Replacement of lamp bulbs
EN10A-Ab
Before replacing a bulb, ensure the lamp
is off. Do not touch the glass part of the
new bulb with your bare fingers; the skin oil
left on the glass will evaporate when the
bulb gets hot and the vapor will con-
dense on the reflector and dim the sur-
face.
N10B307A
Bulb capacity
EN10BOIb
A bulb should only be replaced with a new
bulb of the same rating and type. The des-
ignation can be found on the base of the
bulb.
Outside
1- Headlamps, upper/lower beam
..................................60/55W (H4)
2- Front fog lamps*
........................... 51W(HB4)·9006
3- Front turn-signal lamps . 21W (W21W)
4- Position lamps................ 5W(W5W)
5- Side turn-signal lamps ... 5W (WY5W)
6- Side step lamps*........... 5W(WY5W)
For emergencies
8-34Div:
Out put date:
Page 335 of 392
N10F089A
Front turn-signal lamps
EN10FAQa
Turn the bulb socket anticlockwise to
remove it. And remove the bulb from the
socket by pulling it out.
N10E004A
Side turn-signal lamps
EN10E-Ma
To remove a side turn-signal lamp, insert
a straight blade (or minus) screwdriver at
the front of the lamp, then gently lever the
lamp out of the body.
NOTE
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.
N10A008A
Remove the socket and bulb assembly
together by turning it anticlockwise, and
then remove the bulb by pulling out.
For emergencies
8-37
Div:
Out put date:
Page 339 of 392
N20I025A
Remove the socket and bulb assemblies by
turning them anticlockwise.
Each bulb can be removed from the socket
by pulling it out.
1- Reversing lamp
2- Rear fog lamp (driver’s side only)
N20I026A
(On bumper)
Remove the lens mounting screws.
N20I027A
Remove the socket and bulb assembly
together by turning it anticlockwise, and
then remove the bulb from the socket by
following procedures.
3- Stop and tail lamps
Pull the bulb out.
4- Rear turn-signal lamps
Turn the bulb anticlockwise while press-
ing it inward.
For emergencies
8-41
Div:
Out put date: