keyless entry NISSAN TEANA 2008 Service Manual

ADP-36
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (DRIVER SEAT CONTROL UNIT)
ACTIVE TEST
CAUTION:
When driving vehicle never perform active test.
WORK SUPPORT
SLIDE PULSE — –×Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases
RECLN PULSE — –×Value (32768) when battery connections are standard. If it
moves backward, the value increases. If it moves forward,
the value decreases
LIFT FR PULSE — –×Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases
LIFT RR PULSE — –×Value (32768) when battery connections are standard. If it
moves DOWN, the value increases. If it moves UP, the val-
ue decreases
VEHICLE SPEED —××Display the vehicle speed signal received from combination
meter by numerical value [km/h]
P RANG SW CAN “ON/OFF”××ON/OFF status judged from the P range switch signal
R RANGE (CAN) “ON/OFF”××ON/OFF status judged from the R range switch signal
DOOR SW–FL “ON/OFF”××ON/OFF status judged from the door switch (front driver
side) signal
DOOR SW–FR “ON/OFF”××ON/OFF status judged from the door switch (front passen-
ger side) signal
IGN ON SW “ON/OFF”××ON/OFF status judged from the ignition switch signal
ACC ON SW “ON/OFF”××ON/OFF status judged from the ACC switch signal
KEY ON SW “ON/OFF”××ON/OFF status judged from the key on switch signal
KEYLESS ID —××Key ID status judged from the key ID signal
KYLS DR UNLK “ON/OFF”××ON/OFF status judged from the driver side door unlock ac-
tuator output switch signal
VHCL SPEED (ABS) “ON/OFF”××ON/OFF status judged from vehicle speed signal
HANDLE “RHD/LHD”××RHD/LHD status judged from handle position signal
TRANSMISSION“AT or CVT/
MT”××AT or CVT/MT status judged from transmission
STEERING STATUS“LOCK/UN-
LOCK”××LOCK/UNLOCK status judged from steering lock unit Monitor Item UnitMain
SignalsSelection
From
MenuContents
Test item Description
SEAT SLIDE Activates/deactivates the sliding motor
SEAT RECLINING Activates/deactivates the reclining motor
SEAT LIFTER FR Activates/deactivates the lifting motor (front)
SEAT LIFTER RR Activates/deactivates the lifting motor (rear)
MEMORY SW INDCTR Turns ON/OFF the memory indicator
Work item Content Item
SEAT SLIDE VOLUME SETThe amount of seat sliding for entry/exit assist can be selected
from 3 items.40 mm
80 mm
150 mm

BCS
BODY CONTROL SYSTEM
BCS-7
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
Component Parts LocationINFOID:0000000003809585
Intelligent Key system/engine start systemDoor lock function
DLK-14, "INTELLIGENT KEY SYSTEM : System Diagram"
Trunk open function
Remote keyless entry
function
Key reminder function
Warning function
Engine start function
Power window systemPWC-7, "
SystemDiagram"
System Reference
1. BCM
A. Behind of combination meter
JPMIA1040ZZ

BCS-14
< FUNCTION DIAGNOSIS >
POWER CONSUMPTION CONTROL SYSTEM
Sleep condition
Wake-up operation
 BCM changes from the low power consumption mode to the CAN communication sleep mode when the any
of the BCM wake-up conditions is fulfilled. Only the control with BCM is activated.
 BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions is
fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the
normal mode.
 Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the com-
bination meter transmits the wake up signal to BCM via CAN communication to report the CAN communica-
tion start.
Wake-up condition
CAN sleep condition BCM sleep condition
 Receiving the sleep-ready signal (ready) from all units
 Ignition switch: OFF
 Vehicle security system: Not operation
 Warning chime: Not operation
 Intelligent Key system buzzer: Not operation
 Trunk room lamp switch status: No change
 Stop lamp switch: OFF
 Key slot (card switch) status: No change
 Turn signal indicator lamp: Not operation
Exterior lamp: OFF
 Door lock status: No change
 CONSULT-III communication status: Not communication
 Meter display signal: Non-transmission
 Door switch status: No change
 Rear window defogger: OFF Interior room lamp battery saver: Time out
 Push-button ignition switch illumination: OFF
 Nissan Vehicle Immobilizer System (NVIS) - NATS: Not opera-
tion
 Remote keyless entry receiver communication status: No com-
munication
 ACC indicator lamp: Not operation
 ON indicator lamp: Not operation
BCM wake-up condition CAN wake-up condition
 Trunk lid opener switch: OFF → ON
 Remote keyless entry receiver: Receiving
 Door lock and unlock switch:
NEUTRAL → LOCK, NEUTRAL → UNLOCK
 Front door lock assembly driver side (unlock sensor):
OFF → ON, ON → OFF Receiving the sleep-ready signal (Not-ready) from any units
 Key slot (key switch): OFF → ON, ON → OFF
 Push-button ignition switch (push switch): OFF→ ON
 Hazard switch: OFF → ON
 PASSING switch: OFF → ON, ON → OFF
 TAIL LAMP switch: OFF → ON
 Driver door switch: OFF → ON, ON → OFF
 Passenger door switch: OFF → ON, ON → OFF
 Rear RH door switch: OFF → ON, ON → OFF
 Rear LH door switch: OFF → ON, ON → OFF
 Trunk room lamp switch: OFF → ON, ON → OFF
 Driver door request switch: OFF → ON
 Passenger door request switch: OFF → ON
 Trunk lid request switch: OFF → ON
 Stop lamp switch: ON

BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)INFOID:0000000003897061
WORK SUPPORT
*: Factory setting
DATA MONITOR
TRNK/HAT MNTR
[On/Off]The switch status input from trunk room lamp switch
RKE-LOCK
[On/Off]Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]Unlock signal status received from remote keyless entry receiver Monitor item
[Unit]Description
Test item Operation Description
INT LAMPOnOutputs the interior room lamp control signal to turn map lamp and personal lamp ON
(Map lamp switch is in DOOR position).
Off Stops the interior room lamp control signal to turn map lamp and personal lamp OFF.
STEP LAMP TESTOn Outputs the step lamp control signal to turn step lamp ON.
Off Stops the step lamp control signal to turn step lamp OFF.
LUGGAGE LAMP TESTOn Outputs the trunk room lamp control signal to turn trunk room lamp ON.
Off Stops the trunk room lamp control signal to turn trunk room lamp OFF.
Service item Setting item Setting
BATTERY SAVER SETOn* With the exterior lamp battery saver function
Off Without the exterior lamp battery saver function
ILL DELAY SETMODE 1* 45 sec.
Sets delay timer function timer operation time.
(All doors closed) MODE 2Without the func-
tion
MODE 3 30 sec.
MODE 4 60 sec.
MODE 5 90 sec.
MODE 6 120 sec.
MODE 7 150 sec.
MODE 8 180 sec.
CUSTOM A/LIGHT SET-
TINGMODE 1* Normal
MODE 2 More sensitive setting than normal setting (Turns ON earlier than normal operation.)
MODE 3 More sensitive setting than MODE 2 (Turns ON earlier than MODE 2.)
MODE 4 Less sensitive setting than normal setting (Turns ON later than normal operation.)
Monitor item
[Unit]Description
PUSH SW
[On/Off]The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]The engine status received from ECM with CAN communication

BCS-24
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)INFOID:0000000003897062
WORK SUPPORT
*: Factory setting
DATA MONITOR
ACTIVE TEST
Test item Operation Description
FRONT WIPERHiTransmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.
LoTransmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INTTransmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
Off Stops transmitting the front wiper request signal to stop the front wiper operation.
HEADLAMP WASHER OnTransmits the headlamp washer request signal to IPDM E/R with CAN communication to
operate the headlamp washer operation.
Service item Setting item Setting
HAZARD ANSWER
BACKLock Only* With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob. Unlk Only With unlocking only
Lock/Unlk With locking/unlocking
Off Without the function
Monitor item
[Unit]Description
REQ SW-DR
[On/Off]The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]The switch status input from the hazard switch
RKE-LOCK
[On/Off]Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]Panic alarm signal status received from the remote keyless entry receiver
Test item Operation Description
FLASHERRH Outputs the voltage to blink the right side turn signal lamps.
LH Outputs the voltage to blink the left side turn signal lamps.
Off Stops the voltage to turn the turn signal lamps OFF.

BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L B A
O
P N
ACTIVE TEST
RKE-PANICNOTE:
This item is displayed, but cannot be monitored.
RKE-P/W OPENNOTE:
This item is displayed, but cannot be monitored.
RKE-MODE CHG Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
RKE OPE COUN1When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical values start changing.
RKE OPE COUN2NOTE:
This item is displayed, but cannot be monitored. Monitor Item Condition
Test item Description
BATTERY SAVERThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SETNOTE:
This item is displayed, but cannot be used.
OUTSIDE BUZZERThis test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated when “ON” on CONSULT-III screen is touched.
INSIDE BUZZERThis test is able to check warning chime in combination meter operation.
 Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
 Key warning chime sounds when “KEY” on CONSULT-III screen is touched.
 P position warning chime sounds when “KNOB” on CONSULT-III screen is touched.
INDICATORThis test is able to check warning lamp operation.
 “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
 “KEY” Warning lamp blinks when “RED IND” on CONSULT-III screen is touched.
INT LAMPThis test is able to check interior room lamp operation.
The interior room lamp will be activated when “ON” on CONSULT-III screen is touched.
LCDThis test is able to check meter display information
 Engine start information displays when “BP N” on CONSULT-III screen is touched.
 Engine start information displays when “BP I” on CONSULT-III screen is touched.
 Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
 Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
 P position warning displays when “SFT P” on CONSULT-III screen is touched.
 Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
 Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
 Take away warning displays when “OUTKEY” on CONSULT-III screen is touched.
 OFF position warning displays when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCHThis test is able to check trunk lid opener actuator open operation.
This actuator opens when “OPEN” on CONSULT-III screen is touched.
FLASHERThis test is able to check security hazard lamp operation.
The hazard lamps will be activated when “RH” or “LH”on CONSULT-III screen is touched.
HORNThis test is able to check horn operation.
The horn will be activated when “ON” on CONSULT-III screen is touched.
P RANGEThis test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMIThis test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATORThis test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
ACC INDICATORThis test is able to check ACC indicator in push-ignition switch operation.
ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON INDThis test is able to check ON indicator in push-ignition switch operation.
ON indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

BCS-30
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
*: Each lamp switch is in ON position.
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)INFOID:0000000003897054
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
Monitor item
[Unit]Description
REQ SW-DR
[On/Off]The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]The switch status input from front request switch (passenger side)
PUSH SW
[On/Off]The switch status input from push-button ignition switch
KEY SW-SLOT
[On/Off]Key switch status input from key slot
DOOR SW-DR
[On/Off]The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]NOTE:
The item is indicated, but not monitored.
CDL LOCK SW
[On/Off]Lock switch status received from door lock/unlock switch
CDL UNLOCK SW
[On/Off]Unlock switch status received from door lock/unlock switch
KEY CYL LK-SW
[On/Off]NOTE:
The item is indicated, but not monitored.
KEY CYL UN-SW
[On/Off]NOTE:
The item is indicated, but not monitored.
TRNK/HAT MNTR
[On/Off]The switch status input from trunk room lamp switch
RKE-LOCK
[On/Off]Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]Unlock signal status received from remote keyless entry receiver
Test item Operation Description
BATTERY SAVEROff Cuts the interior room lamp power supply to turn interior room lamp OFF.
On Outputs the interior room lamp power supply to turn interior room lamp ON.*
Diagnosis mode Function Description
DATA MONITOR The BCM input/output signals are displayed.
ACTIVE TEST The signals used to activate each device are forcibly supplied from BCM.

DLK-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G H
I
J
L
M
SECTION DLK
A
B
DLK
N
O P
CONTENTS
DOOR & LOCK
WITH INTELLIGE NT KEY SYSTEM
BASIC INSPECTION ....... .............................
7
DIAGNOSIS AND REPAIR WORKFLOW ..... .....7
Work Flow ........................................................... ......7
INSPECTION AND ADJUSTMENT ....................10
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ....
10
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ................................
10
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .....
10
FUNCTION DIAGNOSIS .. ............................11
POWER DOOR LOCK SYSTEM .................... ....11
System Diagram .................................................. ....11
System Description .................................................11
Component Parts Location ....................................12
Component Description ..........................................12
INTELLIGENT KEY SYSTEM ............................14
INTELLIGENT KEY SYSTEM ...................................14
INTELLIGENT KEY SYSTEM : System Diagram ....14
INTELLIGENT KEY SYSTEM : System Descrip-
tion ..........................................................................
14
INTELLIGENT KEY SYSTEM :
Component Parts Location ....................................
15
INTELLIGENT KEY SYSTEM :
Component Description ..........................................
16
DOOR LOCK FUNCTION ...................................... ....16
DOOR LOCK FUNCTION : System Diagram .........17
DOOR LOCK FUNCTION : System Description .....17
DOOR LOCK FUNCTION :
Component Parts Location ....................................
19
DOOR LOCK FUNCTION :
Component Description ..........................................
20
TRUNK OPEN FUNCTION .................................... ....20
TRUNK OPEN FUNCTION : System Diagram ........21
TRUNK OPEN FUNCTION : System Description ....21
TRUNK OPEN FUNCTION :
Component Parts Location ....................................
23
TRUNK OPEN FUNCTION :
Component Description ..........................................
24
REMOTE KEYLESS ENTRY FUNCTION ..................24
REMOTE KEYLESS ENTRY FUNCTION : Sys-
tem Diagram ........................................................ ....
25
REMOTE KEYLESS ENTRY FUNCTION : Sys-
tem Description ........................................................
25
REMOTE KEYLESS ENTRY FUNCTION :
Component Parts Location ....................................
27
REMOTE KEYLESS ENTRY FUNCTION :
Component Description ..........................................
28
KEY REMINDER FUNCTION ................................ ....28
KEY REMINDER FUNCTION : System Descrip-
tion ...........................................................................
28
KEY REMINDER FUNCTION :
Component Parts Location ....................................
30
WARNING FUNCTION .......................................... ....31
WARNING FUNCTION : System Description ..........31
WARNING FUNCTION :
Component Parts Location ................................ ....
36
TRUNK OPEN FUNCTION ...............................38
System Diagram ......................................................38
System Description ..................................................38
Component Parts Location ....................................38
Component Description ..........................................39
FUEL FILLER LID OPENER .............................40
Component Parts Location ......................................40
DIAGNOSIS SYSTEM (BCM) ...........................41
COMMON ITEM ..................................................... ....41

DLK-2
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ....................................................
41
DOOR LOCK .............................................................42
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) .........................................................
42
INTELLIGENT KEY ...................................................43
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ...................................
43
TRUNK ......................................................................46
TRUNK : CONSULT-III Function (BCM - TRUNK) ...46
COMPONENT DIAGNOSIS ........................48
U1000 CAN COMM CIRCUIT ............................48
BCM ...........................................................................48
BCM : Description ...................................................48
BCM : DTC Logic ....................................................48
BCM : Diagnosis Procedure ...................................48
U1010 CONTROL UNIT (CAN) .........................49
BCM ...........................................................................49
BCM : DTC Logic ....................................................49
BCM : Diagnosis Procedure ...................................49
BCM : Special Repair Requirement ........................49
B2621 INSIDE KEY ANTENNA 1 ......................50
Description ..............................................................50
DTC Logic ...............................................................50
Diagnosis Procedure ..............................................50
B2622 INSIDE KEY ANTENNA 2 ......................52
Description ..............................................................52
DTC Logic ...............................................................52
Diagnosis Procedure ..............................................52
B2623 INSIDE KEY ANTENNA 3 ......................54
Description ..............................................................54
DTC Logic ...............................................................54
Diagnosis Procedure ..............................................54
POWER SUPPLY AND GROUND CIRCUIT .....56
BCM (BODY CONTROL MODULE) .........................56
BCM (BODY CONTROL MODULE) : Diagnosis
Procedure ...............................................................
56
DOOR SWITCH .................................................57
Description ..............................................................57
Component Function Check .................................57
Diagnosis Procedure ..............................................57
Component Inspection ............................................59
DOOR LOCK AND UNLOCK SWITCH .............60
Description ..............................................................60
Component Function Check .................................60
Diagnosis Procedure ..............................................60
DOOR LOCK ACTUATOR ................................61
DRIVER SIDE ............................................................61
DRIVER SIDE : Description ....................................61
DRIVER SIDE : Component Function Check ........61
DRIVER SIDE : Diagnosis Procedure .....................61
PASSENGER SIDE ...................................................61
PASSENGER SIDE : Description ...........................62
PASSENGER SIDE :
Component Function Check ..................................
62
PASSENGER SIDE : Diagnosis Procedure ............62
REAR LH ...................................................................62
REAR LH : Description ...........................................62
REAR LH : Component Function Check ...............63
REAR LH : Diagnosis Procedure ............................63
REAR RH ...................................................................63
REAR RH : Description ...........................................63
REAR RH : Component Function Check ...............63
REAR RH : Diagnosis Procedure ...........................64
TRUNK LID OPENER ACTUATOR ..................65
Description ..............................................................65
Component Function Check ..................................65
Diagnosis Procedure ...............................................65
REMOTE KEYLESS ENTRY RECEIVER .........67
Description ..............................................................67
Component Function Check ..................................67
Diagnosis Procedure ...............................................67
TRUNK LID OPENER SWITCH ........................70
Description ..............................................................70
Component Function Check ..................................70
Diagnosis Procedure ...............................................70
Component Inspection ............................................71
DOOR REQUEST SWITCH ...............................72
Description ..............................................................72
Component Function Check ..................................72
Diagnosis Procedure ...............................................72
Component Inspection ............................................73
TRUNK LID OPENER REQUEST SWITCH ......74
Description ..............................................................74
Component Function Check ..................................74
Diagnosis Procedure ...............................................74
Component Inspection ............................................75
TRUNK ROOM LAMP SWITCH ........................76
Description ..............................................................76
Component Function Check ..................................76
Diagnosis Procedure ...............................................76
Component Inspection ............................................77
UNLOCK SENSOR ............................................78
Description ..............................................................78
Component Function Check ..................................78
Diagnosis Procedure ...............................................78
Component Inspection ............................................79
OUTSIDE KEY ANTENNA ................................80

DLK-6
INSIDE KEY ANTENNA ..................................235
INSTRUMENT CENTER ..........................................235
INSTRUMENT CENTER : Exploded View .............235
INSTRUMENT CENTER : Removal and Installa-
tion .........................................................................
235
CONSOLE ................................................................235
CONSOLE : Exploded View ..................................236
CONSOLE : Removal and Installation ...................236
TRUNK ROOM .........................................................236
TRUNK ROOM : Exploded View ...........................237
TRUNK ROOM : Removal and Installation ............237
OUTSIDE KEY ANTENNA ..............................238
DRIVER SIDE ...........................................................238
DRIVER SIDE : Exploded View .............................238
DRIVER SIDE : Removal and Installation .............238
PASSENGER SIDE ..................................................238
PASSENGER SIDE : Exploded View ....................238
PASSENGER SIDE : Removal and Installation ....238
REAR BUMPER .......................................................238
REAR BUMPER : Exploded View .........................238
REAR BUMPER : Removal and Installation .........238
INTELLIGENT KEY WARNING BUZZER ........240
Exploded View ......................................................240
Removal and Installation .......................................240
KEY SLOT ........................................................241
Exploded View ......................................................241
Removal and Installation .......................................241
TRUNK LID OPENER REQUEST SWITCH .....242
Exploded View ......................................................242
Removal and Installation .......................................242
TRUNK LID OPENER SWITCH .......................243
Exploded View ......................................................243
Removal and Installation .......................................243
REMOTE KEYLESS ENTRY RECEIVER ........244
Exploded View ......................................................244
Removal and Installation .......................................244
INTELLIGENT KEY BATTERY ........................245
Removal and Installation .......................................245