change time Peugeot 208 2013 Owner's Manual

.
19
Familiarisation















































Eco-driving

Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2emissions.


Optimise the use of your gearbox


With a manual gearbox, move off gently, change up without waiting and drive by changing up quite soon. If your vehicle has the system,
the gear shift indicator invites you to change up; it is displayed in the instrument panel, follow its instructions.


With an automatic or electronic gearbox, stay in Drive "D"or Auto "A"
, according to the type of gearbox, without pressing the accelerator pedal heavily or suddenly.


Drive smoothly


Maintain a safe distance between vehicles, use engine braking rather than the brake pedal, and press the accelerator progressively. These practices contribute towards a reduction in fuel consumption and CO2emissions and also helps reduce the background traffic noise.


If your vehicle has cruise control, make use of the system at speeds above 25 mph (40 km/h) when the traffic is flowing well.



Control the use of your electrical
equipment


Before moving off, if the passenger compartment is too warm, ventilate it by opening the windows and air vents before using the air conditioning.
Above 30 mph (50 km/h), close the windows and leave the air ventsopen.
Remember to make use of equipment that can help keep the temperaturein the passenger compar tment down (sunroof and window blinds...).
Switch off the air conditioning, unless it has automatic digital regulation, as soon as the desired temperature is attained.
Switch off the demisting and defrosting controls, if not automatic.
Switch off the heated seat as soon as possible.


Switch off the headlamps and front foglamps when the level of light does not require their use.


Avoid running the engine before moving off, par ticularly in winter; your vehicle will warm up much faster while driving.


As a passenger, if you avoid connecting your multimedia devices (film, music, video game...), you will contribute towards limiting the
consumption of electrical energy, and so of fuel.
Disconnect your por table devices before leaving the vehicle.

42
Instruments and controls
Stop & Start time counter
(minutes / seconds or hours /
minutes)

If dashes are displayed continuously while driving in place of the digits, contact a PEUGEOT dealer or a qualified workshop.
This function is only displayed from 20 mph (30 km/h).


This value may vary following a changein the style of driving or the relief,resulting in a significant change in thecurrent fuel consumption.
Trip computer, a few definitions

Range
(miles or km)
The distance which can still be
travelled with the fuel remainingin the tank. Related to theaverage fuel consumption over
the last few miles (kilometres)
travelled.
When the ran
ge falls below 20 miles (30 km),
dashes are displayed. After filling with at least 5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (10 0 km).
Current fuel consumption
(mpg or l/100 km or km/l) Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l) Calculated since the last trip computer reset.
Average speed
(mph or km/h)Calculated since the last trip computer reset.


Distance travelled
(miles or km)
Calculated since the last trip
computer reset.

I
f your vehicle is fitted with Stop & Star t, a timecounter calculates the time spent in STOP mode during a journey.
It resets to zero every time the ignition isswitched on with the key.

85
4
Driving

Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised, with your foot on the brake pedal. In all cases, you must apply the parkingbrake to immobilise the vehicle.



"Au t o s equential" mode

In automated mode, you can resume control
temporarily at any time using the steeringmounted control paddles.
The use of these paddles permits manual
selection of the gears in situations which
require a more rapid change-down than in
the automated mode (arrival at a roundabout,leaving a car park with a steep gradient,
over taking...).
The gearbox engages the required gear if
the engine speed permits. AUTO
remains
displayed in the instrument panel.
After a few moments, the gearbox resumes
automatic control of the gears.
Stopping the vehicle
Before switching off the engine, you canchange to position N to be in neutral.
In this case,
you must apply the parking braketo immobilise the vehicle.
AUTO
and -appear in the instrument panel.


Operating fault
With the ignition on, if this warninglamp comes on and AUTOflashes, accompanied by an audible signal
and a message in the screen, this indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a qualified workshop.


For best acceleration, when over taking another vehicle for example, press the accelerator pedal firmly to pass the
point of resistance.

)
Select position N
.
Reinitialisation
Following disconnection of the battery, the gearbox must be reinitialised.)
Switch on the ignition.
)
Press the brake pedal.
)
Wait approximately 30 seconds until N
or agear appears in the instrument panel.
)
Release the brake pedal.
The
gearbox is operational again.

91
4
Driving
)Apply the parking brake. )Select position P or N.)Star t the engine.
If this procedure is not followed, there is an audible signal,
accompanied by the display of an warning message.

Moving off


When the engine is running at idle, with the brakes released, if position R, Dor M
is selected, the vehicle moveseven without the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision.
When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
v
ehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.



Return to automatic
o
peration
) At any time, press the button selectedagain to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions of use.
)With the engine running, press
the brake pedal.
)Release the parking brake. )Select position R, Dor M.)
Gradually release the brake pedal.
The vehicle moves off immediately.

92
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value duringmanual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage position P
or Nto place the gearbox in
neutral.
In both cases, apply the parking brake to immobilise the vehicle.


Operating fault
When the ignition is on, the lightingof this warning lamp, accompanied
by an audible signal and a message in the
multifunction screen, indicates a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the P
position to another position when the battery is flat.
To reduce fuel consumption when at a prolonged standstill with the engine
running (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.

102
Driving





Park Assist
This system provides active assistance with parking, detecting a parking space then controlling the steering to park in the space.
It controls the steering while the driver manages the accelerator, brakes, gears and clutch (manual gearbox). During phases of entry into and exit froma parking space, the system provides visual and audible information to the driver in order to make the manoeuvre safe. It may be necessary to move
forwards and backwards more than once.

For entry into a parking space (parallel
parking) the system does not detect spaces which are clearly much smaller or larger than the size of the vehicle.
This "parking assistance" systemis activated automatically duringmanoeuvres; it is therefore possiblethat a symbol comes on in the screen, accompanied by an audible signal,without affecting the manoeuvre.
When Park Assist is activated, it prevents a change to STOP mode of Stop & Star t. In STOP mode, activationof Park Assist restarts the engine.



The Park Assist system cannot in anycircumstances replace the care and responsibility of the driver.
The driver must remain in control of their vehicle ensuring that the space remains clear during the manoeuvre. In some circumstances, the sensors may not detect small obstacles located in their blind spots.
During a manoeuvre the steering wheel
turns quickly: do not hold the steering wheel, do not place your hand between the spokes of the steering wheel andtake care with loose and bulky clothing,scarves, handbags... There is a risk of injury.

The s
ystem provides assistance in entering and exiting a parking space when parallel parking.
The driver can take control at any time by gripping the steering wheel.

186
Practical information
The fitting of electrical equipment or accessories which are not
recommended by PEUGEOT may resultin a failure of your vehicle's electronicsystem and excessive electricalconsumption.
Please note this precaution. You are advised to contact a PEUGEOTrepresentative to be shown the range of recommended equipment and accessories.


Installation of radio communication transmitters

Before installing any after-market radiocommunication transmitter, you can contact a PEUGEOT dealer for thespecification of transmitters which can be fitted (frequency, maximum power, aerial position, specific installation requirements), in line with the Vehicle Electromagnetic Compatibility Directive (2004/104/EC).


Depending on the legislation in forcein the country, it may be compulsory to have a high visibility safety vest, warning triangle and spare bulbs andfuses available in the vehicle.
B
y visiting a PEUGEOT dealer, you can also
obtain products for cleaning and maintenance(exterior and interior) - including ecological
products in the "TECHNATURE" range, topping up products (screenwash...), touch-up pens
and paint aerosols for the exact colour of your
vehicle, refills (cartridge for the temporary
puncture repair kit...), ...
"Multimedia":
audio systems, por table satellite navigation systems, semi-integral suppor t for por tablesatellite navigation system, hands-free kit, CDchanger, speakers, DVD player, connection kit for MP3 or CD player, USB Box, Wi-Fi on-board...

196
Checks






Checking levels
Oil level


The check is carried out either when
the ignition is switched on using theoil level indicator in the instrument
panel, or using the dipstick.

Engine oil change

Refer to the ser vicing and warranty booklet for
details of the inter val for this operation.
In order to maintain the reliability of the engine
and emission control system, the use of
additives in the engine oil is prohibited.

Oil specifi cation

The oil must be the correct grade for your engine and conform to the manufacturer'srecommendations.
Th
e brake fluid level should be close
to the "MA X" mark. If it is not, check
the brake pad wear.
Brake fluid level

Changing the fl uid

Refer to the servicing and warranty booklet for
details of the interval for this operation.

Fluid specifi cation

The brake fluid must conform to themanufacturer's recommendations and meet the
DOT3 or DOT4 standard.



Take care when working under the bonnet, as certain areas of the engine may be extremely hot (risk of burns) and the cooling fan could star t at
any time (even with the ignition off).
If a level drops si
gnificantly, have the corresponding system checked by a PEUGEOT dealer or a qualified workshop. Check all of these levels regularly, in line with the ser vicing booklet and the requirements of the warranties. Top them up if necessary, unless other wise indicated.
It is normal to top up the oil levelbetween two ser vices (or oil changes). PEUGEOT recommends that you check the level, and top up if necessary, every3 000 miles (5 000 kms).

After topping up the oil, the check whenswitching on the ignition with the oil level
indicator in the instrument panel is not valid
durin
g the 30 minutes after topping up. It will onl
y be correct if the vehicle is on level ground and the engine has been off for more
than 30 minutes.

199
8
Checks






Checks
12 V battery
The battery does not require any maintenance.
However, check that the terminals are clean
and correctl
y tightened, particularly in summer and winter.
The presence of this label, in particular with
the Stop & Star t system, indicates the use of
a specific 12 V lead-acid battery with special
technology and specification. The involvement
of a PEUGEOT dealer or a qualified workshop is essential when replacing or disconnecting
the battery.
Particle emissions filter (Diesel)

The star t of saturation of the particle filter is indicated by the fixed
illumination of this warning lamp
accompanied by a warning message
in the screen (if a display screen isfitted).
On a new vehicle, the first particlefilter regeneration operations may beaccompanied by a "burnt" smell, which is perfectly normal.
Following prolonged operation of thevehicle at very low speed or at idle, you may, in exceptional circumstances, notice the emission of water vapour atthe exhaust on acceleration. This does
not affect the behaviour of the vehicle or the environment.
Unless other wise indicated, check these components in accordance with the ser vicin
g and warranty booklet and according to your engine.
Other wise, have them checked by a PEUGEOT dealer or a qualified workshop.
Air filter and passenger compartment filter

Refer to the ser vicing and warrantybooklet for details of the replacement
inter vals for these components.
Oil filter
Replace the oil filter each time theengine oil is changed.
Refer to the servicing and warrantybooklet for details of the replacement
interval for this component. Depending on the environment
(e.g. dustyatmosphere) and the use of the vehicle(e.g. city driving), replace them twice as oftenif necessary.y
A clogged passenger compartment filter may have an adverse effect on the per formance
of the air conditioning system and generateundesirable odours. When carr
ying out work on the battery, refer
to the "Practical information" section for
details of the precautions to be taken before
disconnecting the battery and following its
reconnection.
As soon as the traffic conditions permit,
regenerate the filter by driving at a speed of at
least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, this indicates a
low additive level.

05

ADDING A WAYPOINT
ORGANISING WAYPOINTS

Select "Navigation GPS ".

Select "Waypoints
".

Select "Add
".

The address of the wa
ypoint is entered in
the same way as a destination, so enter
the " City" or post code, the "Street" andthe " N°". Confi rm each time.
Th
en select " As waypoint
".
Select the wa
ypoint that you want to move in
the order.
To or
ganise waypoints, carry out the previous operations 1 to3 again (Adding a waypoint).

Select "Up
".

Select "Down".

Select "Delete
".

Select "Road map
" to view the changes made
to the route.
Select "Guide
".

Select the criteria then "Confi rm
" to start guidance and give the general direction of the navigation route.

Pr
ess MENUto display the " MAIN MENU
" then select " Navigation".
NAVIGATION - GUIDANCE

Select "Address
".