oil temperature PONTIAC G6 2007 Owners Manual

The remote vehicle start feature will not operate if
any of the follow occur:
The remote start system is disabled through
the DIC.
The vehicle’s key is in the ignition.
The vehicle’s hood is open.
The hazard warning ashers are on.
The check engine light is on. SeeMalfunction
Indicator Lamp on page 204.
The engine coolant temperature is too high.
The oil pressure is low.
Two remote vehicle starts have already been
used for that ignition cycle.
Vehicles that have the remote vehicle start feature
are shipped from the factory with the remote
start system enabled. The system may be enabled
or disabled through the DIC. See “REMOTE
START” underDIC Vehicle Personalization on
page 216for additional information.
Remote Start Ready
(Automatic Transaxle Only)
If your vehicle does not have the remote vehicle
start feature, it may have the remote start ready
feature. This feature allows your dealer to add the
manufacturer’s remote vehicle start feature.
If the RKE transmitter has a plus (+) symbol on the
back cover, your vehicle has the remote start ready
feature. You can lock or unlock your vehicle from
approximately 197 feet (60 m) away.
See your dealer if you would like to add the
manufacturer’s remote vehicle start feature to
your vehicle.
107

Engine Coolant Heater
Your vehicle may have this feature. In very cold
weather, 0°F (−18°C) or colder, the engine coolant
heater can provide easier starting and better fuel
economy during engine warm-up. Usually, the
coolant heater should be plugged in a minimum
of four hours prior to starting your vehicle. At
temperatures above 32°F (0°C), use of the coolant
heater is not required. Your vehicle may also have
an internal thermostat in the plug end of the cord.
This will prevent operation of the engine coolant
heater when the temperature is at or above
0°F (−18°C) as noted on the cord.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical cord.
On the 2.4L L4 ECOTEC
®engine, the engine
coolant heater cord is located near the air
cleaner box on the passenger’s side of the
engine compartment. On the 3.5L, 3.6L and
3.9L V6 engines, the engine coolant heater
cord is located on the driver’s side around
the battery box. SeeEngine Compartment
Overview on page 318for more information
on location.3. Plug the cord into a normal, grounded
110-volt AC outlet.
{CAUTION:
Plugging the cord into an ungrounded
outlet could cause an electrical shock.
Also, the wrong kind of extension cord
could overheat and cause a re. You
could be seriously injured. Plug the cord
into a properly grounded three-prong
110-volt AC outlet. If the cord will not
reach, use a heavy-duty three-prong
extension cord rated for at least 15 amps.
4. Before starting the engine, be sure to unplug
and store the cord as it was before to keep it
away from moving engine parts. If you do
not, it could be damaged.
How long should you keep the coolant
heater plugged in? The answer depends
on the outside temperature, the kind
of oil you have, and some other things.
128

Enhanced Traction System Warning
Light...................................................... 202
Enhanced Traction System Active Light..... 202
StabiliTrak
®Not Ready Light...................... 203
StabiliTrak®Indicator Light......................... 203
Engine Coolant Temperature Gage............ 203
Malfunction Indicator Lamp........................ 204
Oil Pressure Light..................................... 207
Security Light............................................ 207
Cruise Control Light.................................. 208
Highbeam On Light................................... 208
Fuel Gage................................................. 208
Low Fuel Warning Light............................ 208
Driver Information Center (DIC).................. 209
DIC Operation and Displays...................... 209
DIC Warnings and Messages.................... 212
DIC Vehicle Personalization....................... 216Audio System(s)......................................... 219
Setting the Time for Radios without Radio
Data Systems (RDS).............................. 220
Setting the Time for Radios with Radio
Data Systems (RDS).............................. 221
Radio with CD........................................... 221
Radio with Six-Disc CD............................. 231
XM Radio Messages................................. 246
Theft-Deterrent Feature............................. 248
Audio Steering Wheel Controls.................. 248
Radio Reception........................................ 249
Care of Your CDs..................................... 250
Care of the CD Player.............................. 250
Fixed Mast Antenna.................................. 250
Backglass Antenna.................................... 250
XM™ Satellite Radio Antenna System....... 251
Section 3 Instrument Panel
162

ICE POSSIBLE:This message displays when the
outside air temperature is cold enough to create
icy road conditions. Adjust your driving accordingly.
KEY FOB BATT (Battery) LOW:This message
displays if the Remote Keyless Entry (RKE)
transmitter battery is low. Replace the battery in
the transmitter. See “Battery Replacement”
underRemote Keyless Entry System Operation on
page 101.
LOW FUEL:This message displays along with a
low fuel warning light on the instrument panel
cluster when your vehicle is low on fuel. Rell the
fuel tank as soon as possible. SeeLow Fuel
Warning Light on page 208,Fuel on page 310,
andFilling the Tank on page 313.
LOW OIL LEVEL:This message may display on
some vehicles. For correct operation of the low oil
sensing system, your vehicle should be on a level
surface. A false LOW OIL LEVEL message may
appear if the vehicle is parked on a grade. The oil
level sensing system does not check for actual oil
level if the engine has been off for a short period of
time. The oil level is never checked while the
engine is running. If the LOW OIL LEVEL message
appears, and your vehicle has been parked on levelground with the engine off for at least 30 minutes,
the oil level should be checked by looking at the oil
dipstick. Prior to checking the oil level, be sure the
engine has been off for a few minutes and your
vehicle is on a level surface. Then check the
dipstick and add oil if necessary. SeeEngine Oil on
page 325.
LOW WASHER FLUID:This message displays
when your vehicle is low on windshield washer
uid. Rell the windshield washer uid reservoir as
soon as possible. See “Adding Washer Fluid”
underWindshield Washer Fluid on page 350.
PARKING BRAKE:This message displays if the
parking brake is left engaged and you try to
drive away. SeeParking Brake on page 135for
more information.
POWER STEERING:This message displays if a
problem has been detected with the electric
power steering, if your vehicle has this feature.
Have your vehicle serviced immediately by
your dealer.
SERVICE AIR BAG:This message displays if
there is a problem with the airbag system.
Have your vehicle serviced immediately by your
dealer.
214

TRUNK AJAR:This message displays when the
trunk lid is not closed completely. Make sure
that the trunk lid is closed completely. SeeTrunk
on page 113for more information.
DIC Vehicle Personalization
The following personalization options may appear
on your vehicle’s audio display by pressing the
MENU button:
OIL LIFE RESET:When this option is displayed,
you can reset the engine oil life system. To
reset the system, seeEngine Oil Life System on
page 328.
UNITS:When UNITS appears on the display,
press the enter button to move between METRIC
or ENGLISH. When you have made your
choice, press the MENU button to record your
selection. The initial setting from the factory
is English for the United States and metric for
Canada.
If you choose English, all information will be
displayed in English units. For example, distance
in miles and fuel economy in miles per gallon
is displayed.If you choose metric, all information will be
displayed in metric units. For example, distance in
kilometers and fuel economy in liters per
100 kilometers is displayed.
The unit measurement will also change the trip
odometer, temperature, and average fuel economy
displays.
REMOTE START:If your vehicle has this feature,
the remote start option can be enabled or
disabled. When REMOTE START appears on the
display, press the enter button to move between
OFF and ON. When you have made your
choice, press the MENU button to record your
selection. The initial setting from the factory is ON.
LOCK HORN:If your vehicle has Remote
Keyless Entry (RKE), this option which allows the
vehicle’s horn to chirp every time the lock
button on the RKE transmitter is pressed, can be
enabled or disabled. When LOCK HORN
appears on the display, press the enter button to
move between ON and OFF. When you have
made your choice, press the MENU button
to record your selection. The initial setting from
the factory is OFF.
216

If you are in an area of extreme cold, where
the temperature falls below−20°F (−29°C), it is
recommended that you use either an SAE 5W-30
synthetic oil or an SAE 0W-30 oil. Both will
provide easier cold starting and better protection
for the engine at extremely low temperatures.
Engine Oil Additives
Do not add anything to the oil. The recommended
oils with the starburst symbol that meet GM
Standard GM6094M are all you will need for
good performance and engine protection.
Engine Oil Life System
When to Change Engine Oil
Your vehicle has a computer system that lets you
know when to change the engine oil and lter.
This is based on engine revolutions and engine
temperature, and not on mileage. Based on driving
conditions, the mileage at which an oil change will
be indicated can vary considerably. For the oil life
system to work properly, you must reset the system
every time the oil is changed.When the system has calculated that oil life has
been diminished, it will indicate that an oil change is
necessary. A CHANGE OIL SOON message will
come on. SeeDIC Warnings and Messages on
page 212. Change your oil as soon as possible
within the next 600 miles (1 000 km). It is possible
that, if you are driving under the best conditions, the
oil life system may not indicate that an oil change is
necessary for over a year. However, your engine oil
and lter must be changed at least once a year and
at this time the system must be reset. Your dealer
has GM-trained service people who will perform this
work using genuine GM parts and reset the system.
It is also important to check your oil regularly and
keep it at the proper level.
If the system is ever reset accidentally, you must
change your oil at 3,000 miles (5 000 km) since
your last oil change. Remember to reset the oil life
system whenever the oil is changed.
328

Automatic Transaxle Fluid
(3.9L V6 Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check the automatic transaxle uid
level is when the engine oil is changed.
Change the uid and lter at the intervals listed
inAdditional Required Services on page 434,
and be sure to use the transaxle uid listed in
Recommended Fluids and Lubricants on page 442.
How to Check Automatic Transaxle
Fluid
Because this operation can be a little difficult, you
may choose to have this done at the dealership
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false
reading on the dipstick.Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are above
90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
335

Engine Coolant
The cooling system in your vehicle is lled with
DEX-COOL®engine coolant. This coolant is
designed to remain in your vehicle for ve years or
150,000 miles (240 000 km), whichever occurs rst,
if you add only DEX-COOL
®extended life coolant.
The following explains your cooling system and
how to add coolant when it is low. If you have a
problem with engine overheating, seeEngine
Overheating on page 342.A 50/50 mixture of clean, drinkable water and
DEX-COOL
®coolant will:
Give freezing protection down to
−34°F (−37°C).
Give boiling protection up to 265°F (129°C).
Protect against rust and corrosion.
Help keep the proper engine temperature.
Let the warning lights and gages work as they
should.
Notice:Using coolant other than DEX-COOL
®
may cause premature engine, heater core,
or radiator corrosion. In addition, the engine
coolant may require changing sooner, at
the rst maintenance service after each
30,000 miles (50 000 km) or 24 months,
whichever occurs rst. Any repairs would not
be covered by your warranty. Always use
DEX-COOL
®(silicate-free) coolant in your
vehicle.
339

If you get the overheat warning with no sign of
steam, try this for a minute or so:
1. In heavy traffic, let the engine idle in
NEUTRAL (N) while stopped. If it is safe to
do so, pull off the road, shift to PARK (P)
or NEUTRAL (N) and let the engine idle.
2. Turn on your heater to full hot at the highest fan
speed and open the windows as necessary.
If you no longer have the overheat warning, you
can drive. Just to be safe, drive slower for about
10 minutes. If the warning does not come back on,
you can drive normally.
If the warning continues, pull over, stop, and park
your vehicle right away.
If there is still no sign of steam, idle the engine for
three minutes while you are parked. If you still have
the warning, turn off the engine and get everyone
out of the vehicle until it cools down.
You may decide not to lift the hood but to get
service help right away.Overheated Engine Protection
Operating Mode
This emergency operating mode allows your
vehicle to be driven to a safe place in an emergency
situation. If an overheated engine condition exists,
an overheat protection mode which alternates ring
groups of cylinders helps prevent engine damage.
In this mode, you will notice a signicant loss in
power and engine performance. The temperature
gage will indicate an overheat condition exists.
Driving extended miles (km) and/or towing a trailer
in the overheat protection mode should be avoided.
Notice:After driving in the overheated engine
protection operating mode, to avoid engine
damage, allow the engine to cool before
attempting any repair. The engine oil will be
severely degraded. Repair the cause of coolant
loss, change the oil and reset the oil life
system. SeeEngine Oil on page 325.
344

(h)Change automatic transaxle uid and lter if
the vehicle is mainly driven under one or more of
these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C) or
higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or delivery
service.
If you do not use your vehicle under any of these
conditions, the uid and lter do not require
changing.
(i)Drain, ush, and rell cooling system. This
service can be complex; you should have
your dealer perform this service. See Engine
Coolant on page 339 for what to use. Inspect
hoses. Clean radiator, condenser, pressure cap,
and ller neck. Pressure test the cooling
system and pressure cap.
(j)A uid loss in any vehicle system could indicate
a problem. Have the system inspected and
repaired and the uid level checked. Add uid if
needed.(k)If you drive regularly under dusty conditions,
inspect the lter at each engine oil change.
(l)Change automatic transaxle uid if the vehicle
is mainly driven under one or more of these
conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C) or
higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or delivery
service.
If you do not use your vehicle under any of these
conditions, the uid does not require changing.
(m)Visually inspect belt for fraying, excessive
cracks, or obvious damage. Replace belt if
necessary.
437