heating PORSCHE CAYNNE 2010 1.G User Guide

82
Air Conditioning, Parking Heater and Heated Rear Window Notes on operation
The parking heater runs on fuel, and it therefore
cannot be switched on after the reserve warning
lights up.
fFor further information on the fuel reserve
warning:
Please see the chapter “FUEL RESERVE WAR-
NING” on Page 120.
The parking heater must be operated at least
once per month with the engine cold.
Ignition off: When the parking heater is running,
the remaining running time is shown on the display
panel.
Operation of the parking heater is clearly audible
when outside temperatures are low and the engine
is cold.
In certain circumstances, exhaust gases may be
visible under the vehicle.Switching on
fPress ON/OFF button .
The most recently activated parking heating or
parking ventilation function is switched on.
Switching off
fPress ON/OFF button again.
Note on operation
fAfter switching off the parking heater using
ON/OFF button , wait for at least
2 minutes before you press the button again.
The combustion chamber is cleaned.
Switching parking heater on and
off
10_Cayenne_21_KW17.book Seite 82 Donnerstag, 9. April 2009 3:33 15

Air Conditioning, Parking Heater and Heated Rear Window
83
E- Parking ventilation symbol
F- ON time symbol
G-Memory symbol
H-ON time
I-Parking heating symbolProgramming the parking heaterThe parking heater has three independent
memories for programming the ON times. The
ON time, together with the associated parking
heating or parking ventilation function, can be
programed in each memory.Complete programming of the parking heater
requires definition of the
– Function and
–ON time.
Programming function
1. Switch ignition off.
2. Press button on the front
air-conditioning control panel.
The symbols for the parking heating I or par-
king ventilation E function flash on the display.
3. Select function.
Press button for parking heating
or button for parking ventilation.
If no other entry is made within 10 seconds, the
display returns to its initial status.
However, the selected function is retained and is
activated when the parking heater is next turned
on.
fFor further information on switching parking
heater on and off:
Please see the chapter “SWITCHING PARKING
HEATER ON AND OFF” on Page 82.
10_Cayenne_21_KW17.book Seite 83 Donnerstag, 9. April 2009 3:33 15

84
Air Conditioning, Parking Heater and Heated Rear Window Programming ON times
1. Switch ignition off.
2. Press button .
3. Select function (parking heating or parking
ventilation).
4. Select the memory using button .
The desired memory can be selected by pres-
sing button several times.
5. Set ON time using the and buttons.
Pressing the buttons adjusts the time on a
minute-by-minute basis. If the button is kept
depressed, the time is adjusted faster.
ON times are only valid for 24 hours.
6. Press ON/OFF button .
Displays F and G flash for approx. 10 seconds.
Flashing of the displays can be ended before
this time has elapsed by pressing the ON/OFF
button again.
After ON/OFF button has been pressed ON
time H, clock symbol F and memory G are
displayed for 2 minutes.
The display then goes out.
The parking heater has now been programed
and the selected memory is active (symbol G
is lit).
Note on operation
Only one memory can be active at any one time.Activating the memory
The parking heater runs for 30 minutes. It then
switches itself off automatically.
The program must be reactivated for every subse-
quent run.
To do this:
1. Switch ignition off.
2. Press button .
3. Select function (parking heating or parking ven-
tilation).
4. Select the memory using button . The
ON time that was last saved is displayed.
5. Press ON/OFF button .
The program is reactivated.
Displays F and G flash for approx. 10 seconds.
The ON/OFF button can be pressed again
to switch off the displays before this time has
elapsed.
After the ON/OFF button has been
pressed, the ON time H, clock symbol F and
memory G are displayed for 2 minutes.
The display then goes out.
The parking heater has now been programed
and the selected memory is active (symbol G
is lit).
Note on operation
Only one memory can be active at any one time.Example:
The parking heater is to activate the parking
heating function at 9:48 a.m.
To do this:
1. Switch ignition off.
2. Press button on the front air-conditio-
ning control panel.
The symbols for the parking heating or parking
ventilation function flash on the display.
3. Press button .
This selects the parking heating function.
4. Select the memory using button .
5. Set ON time to 9:48 a.m. using the and
buttons.
6. Press ON/OFF button .
The parking heater has now been programed
and the selected memory is active.
Note on operation
If the parking heater is switched on manually prior
to program start of an active memory, this will
delete the programming.
The memory must be reactivated if it is needed.
If the memory is not reactivated, the parking
heater will not switch on.
10_Cayenne_21_KW17.book Seite 84 Donnerstag, 9. April 2009 3:33 15

Air Conditioning, Parking Heater and Heated Rear Window
85
Parking heater faultsInitial start-up following period of non-
utilization
If you have not used the parking heater for several
weeks, the system may require the parking heater
to be switched on several times before it actually
“starts up”.
fPlease take a break of approximately
5 minutes between each individual switch-on
attempt.
Requirement for initial start-up of the
parking heater:
–Cold engine.Have the parking heater checked by an authorized
Porsche dealer in the following cases:
– If the parking heater fails to “start-up” after the
3rd switch-on attempt.
– In the event of faults in the parking heater, no
function symbol appears on the display – only
the remaining running time is shown.
The display flashes on briefly and then goes
completely dark.
– In the event of a serious accident, the parking
heater switches off automatically for safety
reasons.
The parking heater is not ready for operation.
– If the temperature rises, the overheating
protection switches the parking heater off
automatically. The parking heater is not ready
for operation.
– The parking heater is switched off automati-
cally if the voltage is too low. The parking
heater is temporarily unavailable.
10_Cayenne_21_KW17.book Seite 85 Donnerstag, 9. April 2009 3:33 15

152
Multi-Purpose Display and Instruments
No monitoring
System learningAfter the tire type and size are selected in the tire pressure menu, Tire Pressure Monitoring re-learns
the tires.Wheel change?
Make new selectionThe tire type and size of the changed tires have not been updated for Tire Pressure Monitoring.
The display changes when the vehicle is stationary: Select corresponding tire type and tire size.When vehicle stops:
Hit selectionThe message appears after driving off if the warning “Flat tyre” has been cleared but the selection on
the display SELECTION AFTER WARNING has not been made properly.
Make selection on the multi-purpose display when the vehicle is stationary.Engine temperature too high Coolant or engine oil temperature is too high. Switch engine off and let it cool.
Check coolant or engine oil level. Add coolant or engine oil if necessary.Check coolant level Switch engine off and let it cool.
Check coolant level. Add coolant if necessary.Warning battery/generator Stop in a suitable place and switch engine off. Do not continue driving.
Have the fault remedied at an authorized Porsche dealer.Start engine The battery discharges if the engine is not running and loads are switched on.
Start the vehicle or switch the loads off.Electric load
Switch-offVehicle electrical system is overloaded. Certain loads (e.g. heated rear window, seat heating) will be
switched off.
Stop immediately at a suitable and secure place and check tank cap for proper fastening. If tank cap
was fastened correctly, consult your authorized Porsche dealer.
Please refuelAdd washer fluidOil level monitoring
FailureHave the fault remedied at an authorized Porsche dealer.Check oil level Check the oil level using the oil dipstick as soon as possible and add engine oil if necessary.
Light on
instrument
panel
Warning message on the multi-purpose
displayMeaning/measures
10_Cayenne_21_KW17.book Seite 152 Donnerstag, 9. April 2009 3:33 15

164
Driving and Driving Safety Brake system warning light
You can check the functionality of the brake sys-
tem warning light by switching the ignition to the
“On” position and verifying that the warning light
illuminates.
The warning light in the instrument panel lights up.
A message will be displayed on the multi-purpose
display of the instrument panel if the brake fluid
level is too low, or (if the brake pedal travel has in-
creased) one of the two brake circuits has failed.
A greater braking pressure will be required, stop-
ping distances will be longer and the braking
behavior will change, particularly in curves.
With correctly adjusted brakes and a correctly
working brake system, the pedal travel to the
point of brake application should be 1-3/16 in. to
1-9/16 in. (30 to 40 mm). Whenever the brake
pedal travel exceeds this value, have the brake
system checked.
Brake pedal
Warning!
Risk of an accident, resulting in serious per-
sonal injury or death.
Any obstruction of the brake pedal could in-
crease the stopping distance.
fAlways check the movement of the brake pedal
before driving and make sure that it is not
obstructed by a floor mat or any other object.
fSecure the floor mat to prevent it from sliding
into positions that could interfere with the safe
operation of your vehicle.
Your Porsche dealer will be glad to offer you
floor mats of the correct size including a securing possibility.
Note
In case one of the two brake circuits fails,
increased pedal travel is required to bring your
vehicle to a full stop.
Warning!
To avoid overheating and premature wear of
the brakes:
fBefore descending a steep grade, reduce
speed and shift the transmission into a lower
gear to control speed.
fDo not “ride the brakes” by resting your foot on
the pedal when not intending to apply brake
pressure.
fDo not hold the pedal down too long or too
often. This could cause the brakes to get hot and not function properly.
Brake warning light USA
Brake warning light
Canada
10_Cayenne_21_KW17.book Seite 164 Donnerstag, 9. April 2009 3:33 15

228
Luggage Compartment, Loadspace and Storage
Ashtray, rearDepending on how the vehicle is equipped, an
ashtray can be installed in the rear door panels.
Opening
fPress ashtray lid briefly.
Emptying
fOpen ashtray cover and press carefully to the
door trim panel.
The insert is raised slightly.
fRemove and empty insert.
Cigarette Lighter
Warning!
Danger of fire and burning. The cigarette
lighter is ready for use, regardless of the
ignition lock position.
fDo not leave children in the car unattended.
fNever touch the heating element or sides of
the lighter.
fHold the lighter by the knob only.
The cigarette lighter is ready for use regardless of
the ignition lock position.Lighter, frontfPress ashtray lid briefly. Ashtray opens inde-
pendently.
fPress lighter into the receptacle. When the ele-
ment is red hot the lighter jumps back to its in-
itial position.
Lighter, rearfPress lighter into the receptacle (arrow). When
the element is red hot the lighter jumps back
to its initial position.
10_Cayenne_21_KW17.book Seite 228 Donnerstag, 9. April 2009 3:33 15

Trailer Hitch
233
Stowing load in the vehicle
Warning!
Danger of injury.
An unsecured or incorrectly positioned cargo
can slip out of place or endanger the vehicle
occupants during braking, direction changes
or in accidents.
Never transport objects which are not
secured.
fAlways transport cargo in the cargo area,
never in the passenger compartment (e.g. on
or in front of the seats).
fSupport the cargo on the seat backrests
whenever possible. Always lock the backrests
into place.
fPlace the cargo behind unoccupied seats
whenever possible.
fStow heavy objects as close to the front of the
cargo area as possible, with lightweight ob-
jects behind them.
fThe cargo must never project over the top
edge of the seat backrest.
fAlways protect the passenger compartment
with a luggage safety net and a luggage
compartment cover.
Do not drive with objects on top of the luggage
compartment cover.fIf the rear seats are not occupied, the back-
rests can be additionally secured with the safe-
ty belts. Simply cross the outer safety belts
and insert each into the opposite buckle.
fMake sure that the cargo cannot damage the
heating filaments of the rear window and the
TV antenna of the side window.
Luggage net
fLuggage must be stowed completely covered
by the luggage net.
The luggage net can prevent only lightweight
objects from slipping.
Tie-down belts
fDo not use elastic belts or straps to tie down
cargo.
fDo not place belts and straps over sharp
edges.
fObserve the directions for use and information
for the tie-down equipment.
fUse only belts with a tear strength of at least
1543 lbs. (700 kg) and a maximum width of
1in. (25mm).
fCross the belts over the load.Driving
fThe car's handling changes depending on the
vehicle loading. Adapt your driving style to the
changed driving behavior.
fDo not exceed the maximum gross weight and
the axle load.
fPlease see the chapter “WEIGHTS” on
Page 356.
fNever drive with the rear window or rear lid
open.
Exhaust gases can enter the passenger
compartment.
fAdapt the tire pressure to the load.
fPlease see the chapter “SETTING VEHICLE
LOADING AND ADJUSTING TIRE PRESSURE”
on Page 135.
fPlease see the chapter “TIRE PRESSURES,
COLD (68 °F/20 °C)” on Page 354.
10_Cayenne_21_KW17.book Seite 233 Donnerstag, 9. April 2009 3:33 15

Parking
243
Programming a button on the keypad
Caution!
Risk of damage. When programming a gara-
ge door or gate, the door or gate may open
and close several times in quick succession,
causing the motor to overheat.
fUnplug the garage door or gate during the pro-
gramming procedure to prevent the motor from overheating.
1. Press and hold the desired button on the
keypad until light-emitting diode B starts to
flash slowly (may take up to 20 seconds).
Do not release the button before step 3 has
been completed.2. Hold the original remote control approx.
5–30 cm in front of the marked position C.
Make sure that the battery in the original
remote control is new.
3. Press and hold the button on the original remo-
te control until light-emitting diode B flashes ra-
pidly.
The rapidly flashing LED B confirms that the re-
mote control function has been programmed
successfully.
Only release both buttons when LED B flashes.
4. Press the programmed button on keypad A.
If the light-emitting diode B lights up conti-
nuously after programming, this means that
the system is a fixed-code system. Program-
ming is now completed.
If light-emitting diode B again flashes rapidly
for a short time after programming and then
lights up continuously for approx. 2 seconds,
this means that the system is a changeable-
code system. HomeLink must then be synchro-
nized with the receiver of the garage door ope-
ner after programming.
5. Repeat steps 1 to 4 to program the other
buttons.
Synchronization for changeable-code
systems
1. To synchronize the system:
Press the programming button on the receiver
of the garage door opener.
Afterwards, you usually have approx.
30 seconds to initiate step 2.2. Press the previously programmed button on
the keypad three times (for approx. 1 second).
Changeable-code synchronization is now com-
pleted.
3. Repeat steps 1 to 2 to synchronize other
signals to the other buttons.
Note
fPlease consult an authorized Porsche dealer if
you have not been able to successfully assign
signals to the buttons even though you have
carefully followed the instructions in this
section and the operating instructions for the
original remote control. Your authorized
Porsche dealer also has a list of all compatible
garage door opener systems.
Operating the garage door openerfPress the corresponding button on keypad A.
Light-emitting diode B lights up continuously
during signal transmission with fixed-code
systems.
In the case of signal transmission for change-
able-code systems, light-emitting diode B
repeatedly lights up rapidly for a short time
and then lights up continuously for approx.
2seconds.
10_Cayenne_21_KW17.book Seite 243 Donnerstag, 9. April 2009 3:33 15

Maintenance and Car Care
265
The catalytic converters will be damaged by:
– push or tow starting the vehicle
– misfiring of the engine
– turning off the ignition while the vehicle is
moving or
– driving until the fuel tank is completely empty
– by other unusual operating conditions.
fDo not continue to operate your vehicle under
these conditions, since raw fuel might reach
the catalytic converters. This could result in
overheating of the converters. Federal law
prohibits use of leaded fuel in this car.
Fuel EconomyFuel economy will vary depending on where,
when and how you drive, optional equipment
installed, and the general condition of your
car.
A car tuned to specifications and correctly
maintained, will help you to achieve optimal
fuel economy.
fHave your vehicle tuned to specifications. Air
cleaner should be dirt free to allow proper
engine “breathing”.
Battery should be fully charged.
Wheels should be properly aligned.
Tires should be inflated to the correct
pressure.
fAlways monitor your fuel consumption.
fDrive smoothly, avoid abrupt changes in speed
as much as possible.
fAvoid jack rabbit starts and sudden stops.
fDo not drive longer than necessary in the lower
gears. Shifting into a higher gear early without
lugging the engine will help save fuel.
fProlonged “warm up” idling wastes gas. Start
the vehicle just before you are ready to drive.
Accelerate slowly and smoothly.fSwitch off the engine if stationary for longer
periods.
fAny additional weight carried in the vehicle
re d u c e s f u e l e c o n o m y. A l w a ys k e e p c a rg o t o a
minimum and remove all unnecessary items.
fOrganize your trips to take in several errands
in one trip.
fAll electrical accessories contribute to
increased fuel consumption.
fOnly switch on the air conditioning when neces-
sary.
fDo not drive with the Roof Transport System
mounted unless you need it.
The EPA estimated miles per gallon (mpg) is
to be used for comparison purposes, actual
mileage may be different from the estimated
mpg, depending on your driving speed,
weather conditions and trip length. Your
actual highway mileage will probably be less
than the estimated mpg.
fPlease see all local and national speed limits.
10_Cayenne_21_KW17.book Seite 265 Donnerstag, 9. April 2009 3:33 15