ad blue RENAULT MEGANE SCENIC 1995 Service Repair Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1995, Model line: MEGANE SCENIC, Model: RENAULT MEGANE SCENIC 1995Pages: 2492, PDF Size: 32.28 MB
Page 11 of 2492
DESCRIPTIONPACKAGINGPART NUMBER
1 kg tin
100 g tube
80 ml tube
180 g sachet
Aerosol77 01 421 145
77 01 028 179
77 01 422 307
77 01 366 100
77 01 422 308
LUBRICANTS
LUBRICANTS - CONSUMABLES
Packaging
04
•MOLYKOTE "BR2"
for main bearing journal faces, thrust pad
guide tubes, clutch fork pads, lower suspension
arm bearings, torsion bar splines, steering box,
driveshaft splines.
•
MOLYKOTE "33 Medium"
tubular rear axle rings
anti-roll bar rings.
•
ANTI-SEIZE
(high temperature grease) Turbo etc.
•
"MOBIL CVJ" 825 Black star
or MOBIL EXF57C
for driveshaft joints
•
MULTIPURPOSE LUBRICANT
wheel sensor
• Perfect-seal "LOWAC"
coating fluid for seals.
• Mastic
for sealing exhaust pipe unions.
•
HARDENER KIT
("CAF 4/60 THIXO")
for sealing sides of bearing caps.
• AUTO joint blue
sealing paste.
100 g tube
1.5 kg tin
Kit
100 g tube
45 g tube77 01 417 404
77 01 421 161
77 01 421 080
77 01 396 227
77 01 397 027
MECHANICAL SEALANTS
04-1
Page 277 of 2492
COOLING
Checking
2 - Checking the rating of the expansion bottle
cap
If fluid passes through the expansion bottle cap
valve, the cap must be replaced.
On the pump M.S. 554-07 fit tool M.S. 554-06 and
fit this to the valve to be checked.
Increase the pressure which should stabilise at the
calibration value for the cap valve, with a test to-
lerance of
± 0.1 bar.
Valve rating value:
19
1 - Checking the cooling circuit sealing
Replace the expansion bottle cap with tool
M.S.
554-01.
To this, connect tool M.S. 554-07.
Let the engine warm up then turn the ignition off.
Pump to put the circuit under pressure.
Stop pumping at 0.1 bar less than the rating value
of the expansion bottle cap.
The pressure should not drop. If it does, look for
the leak.
Slowly unscrew the union of tool M.S. 554-07 to
decompress the cooling circuit, then remove tool
M.S. 554-01 and refit the expansion bottle cap fit-
ted with a new seal.
SPECIAL TOOLING REQUIRED
M.S.554-07 Kit for checking cooling circuit sealing
M.S.554-01 Adaptor for M.S. 554-05
M.S.554-06 Adaptor for M.S. 554-05
97871R
Engine Valve colour Rating (in bar)
F8Q - E7JBrown 1.2
K7M - F3RBlue 1.6
19-3
Page 282 of 2492
COOLING
Diagram
19
1 Engine
2 Radiator
3 Expansion bottle with degassing after ther-
mostat
4 Heater matrix
5 Thermostat mounting
6 Throttle body
7 3 mm diameter restriction
8 8 mm diameter restrictionWater pump
Thermostat
Bleed valve
Temperature switch
The rating of the expansion bottle cap is 1.6 bar
(blue).
99415R
F3R ENGINE
19-8
Page 284 of 2492
COOLING
Diagram
19
1 Engine
2 Radiator
3 Expansion bottle with degassing after ther-
mostat
4 Heater matrix
5 Thermostat mounting
6 3 mm diameter restrictionWater pump
Thermostat
Bleed valve
Temperature switch
The rating of the expansion bottle cap is 1.6 bar
(blue).
99413R
K7M ENGINE
19-10
Page 285 of 2492
COOLING
Diagram
19
1 Engine
2 Radiator
3 Expansion bottle with degassing after ther-
mostat
4 Heater matrix
5 Thermostat mounting
6 Automatic transmission oil temperature ex-
changer
7 3 mm diameter restriction
8 6 mm diameter restrictionWater pump
Thermostat
Bleed valve
Temperature switch
The rating of the expansion bottle cap is 1.6 bar
(blue).
99412R
K7M ENGINE / AT
19-11
Page 311 of 2492
85873S 90693R3
CLUTCH
Identification
20
ENGINE
TYPEMECHANISMPLATE
180 DST 3050
E7JBC= White
BU= Blue
R= Red
N= Black
76906R 90693R4 85873S
180 CP 3300 E7J
26 splines
E = 8.5 mm
D = 181.5 mm
76906R
V= Green
G= Grey blue
B= White 26 splines
E = 8.3 mm
D = 181.5 mm
20-1
Page 1535 of 2492
MECHANISMS OF OPENINGS OTHER THAN SIDE DOORS
Hydraulic system (pipes)
52
Remove:
- the pump connectors (1) and wiring,RR R R
EE E E
MM M M
OO O O
VV V V
AA A A
LL L L
After removing the complete system, mark the co-
lour of the connectors (1) on the solenoid valves.
PRE5204
12298R
12297R
- the pump bolts (2) and bracket. B = blue
R = red
52-13