tailgate RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 391
Page 347 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 347
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 347V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP27 Locking/unlocking fault when pressing card button.
NOTESCheck that there is no APC or card in the card reader.
Check that no opening element is detected as open by the UCH (look at the symbol on
the instrument panel).
First carry out a function fault finding check.
Test with the other card.
Check the condition of the battery (inserted the wrong way round, flat, incorrect
model).
If the fault is still present after having carried out a test with the other card, it could be that:
–There may be radiofrequency interference in the area (ET066 Card button press received is NO for both
cards). Move the vehicle to try again.
–The UCH which has just been replaced does not have the correct part number (external or internal UCH
aerial). Use the correct UCH part number.
–If the vehicle is a Scenic II fitted with a tyre pressure monitoring system, check that the external UCH aerial
is connected correctly.
–Check that the UCH for the vehicle is not blank. Check that the UCH on the vehicle has not been used on
another vehicle.
Check that statuses ET066 Card button press received and ET067 Card button press recognised are YES
after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that statuses ET066 Card button press received and ET067 Card button press recognised are YES
after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that status ET014 Control power level is not APC.
If not, apply the fault finding procedures for this status.
Check that statuses ET041 Opening rear screen, ET042 Passenger's door, ET050 Tailgate/Boot, ET051 Rear
left-hand door, ET052 Rear left-hand door and ET053 Driver's door are CLOSED.
If not, apply the fault finding procedures for those statuses.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP27 /UCH_V48_ALP27/UCH_V4C_ALP27/
UCH_V4D_ALP27/UCH_V4F_ALP27/UCH_V50_ALP27
Page 348 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 348V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP28 Fault locking/unlocking boot via card button
NOTESCheck that there is no APC or card in the card reader.
First carry out a function fault finding check.
Test with the other card.
Check the condition of the batteries.
Check if the direction indicator lights flash once on unlocking and twice on locking.
NOYES
Check that statuses ET066 Card button press received and ET067 Card button press
recognised are YES after pressing the card's lock or unlock button.
If not, apply the fault finding procedures for those statuses.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP28 /UCH_V48_ALP28/UCH_V4C_ALP28/
UCH_V4D_ALP28/UCH_V4F_ALP28/UCH_V50_ALP28
Page 349 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 349
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 349V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP29 Boot opening fault (not hands-free)
NOTESFirst carry out a function fault finding check.
The vehicle or boot must be unlocked.
Check that status ET061 Open tailgate request becomes PRESENT after pressing the boot opening button.
If not, apply the fault finding procedures for this status.
Check that the boot is not detected as OPEN using status ET050 Tailgate/Boot.
If not, apply the fault finding procedures for this status.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP29 /UCH_V48_ALP29/UCH_V4C_ALP29/
UCH_V4D_ALP29/UCH_V4F_ALP29/UCH_V50_ALP29
Page 350 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 350
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 350V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP30 Opening rear screen fault (not hands-free)
NOTESFirst carry out a function fault finding check.
The vehicle or boot must be unlocked.
Make sure status ET062 Open rear screen request becomes PRESENT when the rear screen opening button is
pressed.
If not, apply the fault finding procedures for this status.
Check that the tailgate is not detected as OPEN using status ET041 Opening rear screen.
If not, apply the fault finding procedures for this status.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP30 /UCH_V48_ALP30/UCH_V4C_ALP30/
UCH_V4D_ALP30/UCH_V4F_ALP30/UCH_V50_ALP30
Page 355 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 355
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 355V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP34 Fault opening the boot in hands-free mode
NOTESFirst carry out a function fault finding check.
Vehicle locked.
Test with the other card.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check that status ET061 Open tailgate request becomes PRESENT after pressing the tailgate opening button.
If not, apply the fault finding procedures for this status.
When the tailgate unlocking button is pressed, if the card is present and recognised, the direction indicator lights
should flash to indicate that the tailgate is being unlocked.
NOYES
Check the condition and connection of the tailgate lock connector.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check for earth on connection MZ of component 1322.
Check, when pressing on the opening button, for + 12 V on connection 20S of component 1322.
If correct, replace the tailgate lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP34 /UCH_V48_ALP34/UCH_V4C_ALP34/
UCH_V4D_ALP34/UCH_V4F_ALP34/UCH_V50_ALP34
Page 357 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 357
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 357V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP34
CONTINUED 2
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Check that status ET061 Open tailgate request becomes PRESENT after pressing the tailgate opening button.
If not correct, use the fault finding procedure associated with this status.
Check, using status ET050 Opening rear screen that the tailgate is not considered OPEN.
If not, apply the fault finding procedures for this status.
Check the condition and connection of the boot lock connector.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for earth on connection MZ of component 1322.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check, when pressing on the opening button, for + 12 V on connection 20S of component 1322.
If correct, replace the tailgate lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
Page 358 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 358
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 358V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP35 Fault opening the rear screen in hands-free mode
NOTESFirst carry out a function fault finding check.
Vehicle locked.
Test with the other card.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Make sure status ET062 Open rear screen request becomes PRESENT when the tailgate opening button is
pressed.
If not, apply the fault finding procedures for this status.
When the rear screen opening button is pressed, if the card is present and recognised, the direction indicator lights
should flash to indicate that the boot is being unlocked.
NOYES
Check the connection and condition of the rear screen lock connector.
Repair if necessary.
Check for earth on connection MZ of component 1322.
Repair if necessary.
Check, when pressing on the opening button, for + 12 V on connection 20S of component 1322.
If correct, replace the rear screen lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
UCH_V44_ALP35 /UCH_V48_ALP35/UCH_V4C_ALP35/
UCH_V4D_ALP35/UCH_V4F_ALP35/UCH_V50_ALP35
Page 360 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 360
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart87B
87B - 360V9 MR-372-J84-87B000$946.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP35
CONTINUED 2
NOTESOnly check this customer complaint after performing a complete check with the
diagnostic tool.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
Make sure status ET061 Open rear screen request becomes PRESENT when the tailgate opening button is
pressed.
If not correct, use the fault finding procedure associated with this status.
Check, using status ET050 Opening rear screen that the tailgate is not considered OPEN.
If not, apply the fault finding procedures for this status.
Check the connection and condition of the rear screen lock connector.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check for earth on connection MZ of component 1322.
If one of the connectors is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring
repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check, when pressing on the opening button, for + 12 V on connection 20S of component 1322.
If correct, replace the boot lock.
If the fault is still present, contact Techline.
AFTER REPAIRCarry out a complete check using the diagnostic tool.
Page 367 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -367
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -367V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP42The vehicle does not start, the after ignition feed fails in hands-
free mode but works with the card in the card reader
NOTESFirst carry out a function fault finding check.
Test with the other card.
Switching to + accessories feed should work.
If not deal with ALP39 Accessories feed not activated first.
Check that the start-up conditions are met:
Check that the tailgate is detected as closed by the UCH using status ET050 Tailgate/
Boot.
Carry out the tests with the other cards allocated to the vehicle.
The card may be inhibited or the vehicle was not unlocked electrically: unlock by pressing the card button and
check if the hands-free starting fault is still present.
If the hands-free starting fault affects only one card:
Check that the card battery has been inserted the right way round. If the battery is flat or an incorrect model is being
used, replace the battery. If not, replace the faulty card.
If the hands-free starting fault affects every card:
Make sure the UCH is properly configured for hands-free operation. Reconfigure if necessary.
Make sure that the cards belong to the vehicle and are properly configured by running command SC005 Check
card.
If the cards belong to the vehicle but are incorrectly configured, program the cards.
Run command AC037 Transmitter aerial fault finding and see if a fault appears.
In the event of a present or stored fault, refer to the procedure for it.
If the vehicle is fitted with a tyre pressure monitor (Scénic II only), check that the external UCH aerial is correctly
connected.
Run command AC036 Interior aerial test and check the card coverage zone.
The card reader starts to flash as soon as a card is detected in the coverage zone.
The card should not be detected by the internal aerials when it is outside the vehicle.
If not correct, apply the relevant fault finding procedure for each command.
This mode allows of a Mégane hands-free type card to be detected as present, but not recognised.
Check the part number of the UCH and that it is hands-free.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP42 /UCH_V48_ALP42/UCH_V4C_ALP42/
UCH_V4D_ALP42/UCH_V4F_ALP42/UCH_V50_ALP42