fold seats SKODA CITIGO 2013 1.G Owner's Manual
[x] Cancel search | Manufacturer: SKODA, Model Year: 2013, Model line: CITIGO, Model: SKODA CITIGO 2013 1.GPages: 176, PDF Size: 10.54 MB
Page 33 of 176
Unlocking›Fold the rear seat backrest forward » page 45, Folding the rear seats forward .›
Insert the vehicle key or a similar tool into the opening
A
» Fig. 18 in the lid trim
up to the stop.
›
Unlock the lock in the direction of arrow.
›
Open the boot lid.
Electrical power windows
Introduction
This chapter contains information on the following subjects:
Open / close window
30
Manually opening/closing rear windows
31
The electrical power windows can only be operated when the ignition is switched
on.
WARNING■ If the vehicle is locked from the outside, do not leave anybody in the vehicle
as it is not possible to open the windows from the inside in the event of an
emergency.■
When closing the windows, proceed with caution so as to avoid causing
crushing injuries - risk of injury!
CAUTION
■ Keep the windows clean to ensure the correct functionality of the electric win-
dows.■
If the windows are frozen, first of all remove the ice » page 117, Windows and
exterior mirrors . Only then can the electrical power windows be operated, as oth-
erwise the window seal and the electrical power window mechanism could be
damaged.
■
Make sure that the windows are closed whenever you leave the locked vehicle.
For the sake of the environment
The windows must be kept closed at high speeds in order to prevent unnecessa-
rily high fuel consumption.NoteThe heating, air conditioning and ventilation system should be used to ventilate
the inside of the vehicle while driving. If the windows are open, dust as well as
other dirt can get into the vehicle, and there may also be wind noise at certain
speeds.
Open / close window
Fig. 19
Button on the driver's door
First read and observe the introductory information and safety warn- ings on page 30.
Opening
›
The window is opened by pressing lightly on the corresponding button. The opening process stops when one releases the button.
Closing
›
The window is closed by pulling lightly on the corresponding upper edge of the
button. The closing process stops when one releases the button.
30Using the system
Page 45 of 176
Seats and stowing
Front seats
Introduction
This chapter contains information on the following subjects:
Adjusting the front seats
43
Foldable front passenger seat
43
Front seat heating
44
The driver's seat should be adjusted in such a way that the pedals can be fully
pressed to the floor with slightly bent legs.
The seat backrest on the driver's seat should be adjusted in such a way that the
upper point of the steering wheel can be easily reached with slightly bent arms.
Correct adjustment of the seats is particularly important:
› for safely and quickly reaching the controls;
› for a relaxed body position that reduces fatigue;
› for achieving maximum protection from the seat belts and the airbag system.
WARNINGGeneral information■Caution when adjusting the seat! You may suffer injuries or bruises as a re-
sult of adjusting the seat without paying proper attention.■
The seat backrests must not be tilted too far back when driving, as this will
impair the function of the seat belts and of the airbag system – risk of injury!
■
Never carry more people than the number of seats in the vehicle.
■
Each occupant must correctly fasten the seat belt belonging to the seat.
Children must be fastened » page 103, Transporting children safely with a
suitable restraint system.
■
The front seats and the head restraints must always be adjusted according
to height, so that the occupants can be protected as effectively as possible.
■
Do not carry any objects on the front passenger seat except objects de-
signed for this purpose (e.g. child seat) – risk of accident!
WARNINGInformation for the driver■Only adjust the driver's seat when the vehicle is stationary – risk of accident!■
Maintain a distance of at least 25 cm to the steering wheel. Not maintaining
this minimum distance will mean that the airbag system will not be able to
properly protect you – risk to life!
■
Ensure that there are no objects in the driver's footwell, as these may get
caught in the pedal apparatus when driving or braking. You would then no
longer be able to operate the clutch, brake or acceleration pedals.
WARNINGInformation for the front seat passenger■Maintain a distance of at least 25 cm to the dash panel. Not maintaining this
minimum distance will mean that the airbag system will not be able to proper-
ly protect you – hazard!■
Always keep your feet in the footwell when the car is being driven – never
place your feet on the instrument panel, out of the window or on the surfaces
of the seats. You will be exposed to increased risk of injury if it becomes nec-
essary to apply the brake or in the event of an accident. If an airbag is de-
ployed, you may suffer fatal injuries when adopting an incorrect seated posi-
tion!
Note
After a certain time, play can develop within the adjustment mechanism of the
backrest angle.
42Using the system
Page 46 of 176
Adjusting the front seatsFig. 35
Control elements at the seat
First read and observe the introductory information and safety warn-
ings on page 42.
Adjusting a seat in a forward/back direction
›
Pull the lever
1
» Fig. 35 up and push the seat into the desired position.
›
Release the lever
1
and push the seat until the lock clicks into place.
Adjusting height of seat
›
In order to raisethe seating position, pull up the lever
2
» Fig. 35 or move it
back and forth until the desired position is reached.
›
To lower the seat position, push the lever
2
down or move it back and forth un-
til the desired position is reached.
Adjusting the angle of the seat backrest
›
Remove the load on the seat backrest (do not lean on it), pull the lever
3
» Fig. 35 or
4
1)
towards the rear and set the desired angle of the seat back-
rest with the back.
Folding the front seat forwards and moving it 1)
›
Pull the lever
3
» Fig. 35 or
4
a fold the backrest fully forwards. At the same
time, move the seat forwards.
Moving seats into the initial position 1)
›
Move the seat towards the rear until the lock is heard to engage.
›
Then push the seat backrest back into the upright position until the unlocking
button clicks into place - check by pulling on the seat backrest.
Foldable front passenger seatFig. 36
Folding the front passenger seat
forward
First read and observe the introductory information and safety warn-
ings on page 42.
The front passenger seat can be folded forward into a horizontal position.
Folding forward
›
Place the lever in position 1 » Fig. 36 .
›
Fold the seat backrest forward in the direction of the arrow 2.
The locking mechanism must audibly snap into place.
The seat automatically moves forwards to the stop 1)
.
Folding backward
›
Place the lever in position 1 » Fig. 36 .
›
Fold the seat backrest backward in the opposite direction of the arrow 2.
The locking mechanism must audibly snap into place.
The seat automatically moves backwards to the stop 1)
.
The seat automatically moves backwards into the preset position 2)
.
1)
Applies to front seats with the Easy Entry system.
2)
Applies to front seats with the Easy Entry system and Memory function.
43Seats and stowing
Page 47 of 176
WARNING■The front passenger airbag should be switched off when transporting ob-
jects on the seat backrest that has been folded forwards » page 102.■
Only adjust the seat backrest when the vehicle is stationary.
■
When moving the seat backrest, make sure that the seat backrest has been
properly secured – check by pulling on the seat backrest.
■
If the seat backrest is folded, passengers may only be transported on the
outer seat behind the driver.
■
When moving the seat backrest, keep limbs out of the area between the
seat and seat backrest – risk of injury!
■
The seat backrest that has been folded forwards must never be used to
transport objects that: ■could restrict the driver's view;
■ can make it impossible for the driver to operate the vehicle, e.g. if they
could fall under the pedals or protrude into the driver's area; ■ could injure passengers when the driver accelerates sharply, changes di-
rection or brakes.
Front seat heating
Fig. 37
Heated front seats
First read and observe the introductory information and safety warn- ings on page 42.
The front seats can be heated electrically. In some seat versions, the seat back-
rest is heated as well.
The seat heating can only be switched on when the engine is running.
›
Press the symbol button
or
» Fig. 37 .
Pressing once switches the seat heating on at its maximum level.
With repeated pressing of the switch, the level of the seat heating is down-regu-
lated up to the switch-off. The level of the seat heating is indicated by the num-
ber of illuminated warning lights in the switch.WARNINGIf, as an occupant, you have a subdued pain and/or temperature sensitivity,
e.g. through medication, paralysis or because of chronic illness (e.g. diabetes),
we recommend you do not use seat heating on the driver or front passenger
seat. This can lead to burns on the back, the posterior and the legs which are difficult to heal. If the seat heating is used, we recommend to make regular
breaks in your journey when driving long distances, so that the body can recu-
perate from the stress of the journey. Please consult your doctor, who can evaluate your specific condition.
CAUTION
■ Do not kneel on the seats or otherwise apply pressure at specific points to
avoid damaging the heating elements for the seat heaters.■
Do not turn on the seat heater if seats are not occupied.
■
Do not switch on the seat heating if the seats have objects attached to or
placed on them, for example a child seat, a bag, etc. A fault of the heating ele- ments in the seat heating can occur.
■
If additional seat covers or protective covers are attached to the seats, do not
turn on the seat heater - there is a risk of damaging the seat covers and seat
heating.
■
Do not clean the seats using moisture » page 120, Seat covers .
Note
If the on-board voltage drops, the seat heating is switched off automatically, in
order to provide sufficient electrical energy for the engine control » page 137,
Automatic load deactivation .
44Using the system
Page 48 of 176
Rear seats
Introduction
This chapter contains information on the following subjects:
Folding the rear seats forward
45
Head restraints
45
Folding the rear seats forward
Fig. 38
Unlock the seat backrest
First read and observe the introductory information given on page 45.
The rear seat backrest can be folded forwards to increase the size of the luggage
compartment.
Folding the seat backrest forwards
›
Push the release handle
A
» Fig. 38 to unlock the seat backrest and fold it for-
ward.
›
Move the head restraint fully towards the rear, or remove » page 45, Head re-
straints .
Folding the seat backrest back into position
›
Push the head restraint into the slightly lifted seat backrest » page 45, Head
restraints .
›
Then push the seat backrest back into the upright position until the unlocking
handle clicks into place - check by pulling on the seat backrest » .
›
Make sure that the red marker
B
» Fig. 38 is hidden.
WARNING■
The belts and the belt locks must be in their original position after folding
back the seat backrests – they must be ready to use.■
The seat backrests must be securely locked in position so that no objects in
the luggage compartment can slide into the passenger compartment on sud-
den braking – risk of injury.
■
Ensure that the rear seat backrests are properly engaged. It is only then that
the three-point seat belt can reliably fulfil its function.
CAUTION
Ensure that the seat belts are not damaged when operating the seat backrests. Under no circumstances must the rear seat belts be jammed by the folded back
seat backrests.
Head restraints
Fig. 39
Head restraints rear: adjusting/
removing
First read and observe the introductory information given on page 45.
Only the rear head restraints can be height-adjusted or removed or installed.
Setting height
›
Grasp the side of the head restraint with both hands and push it upwards as re-
quired » Fig. 39 .
›
To move the head restraint downwards, press and hold the safety button
1
with one hand and press the head restraint downwards with the other hand.
Removing/installing
›
Fold the seat backrest a little forward » page 45, Folding the rear seats forward .
45Seats and stowing
Page 49 of 176
›Grasp the side of the head restraint with both hands and push it upwards as re-
quired.›
Press the safety button
1
» Fig. 39 with one hand and keep it pressed down
and use the other hand to remove the head restraint.
›
To reinstall, press the safety button
1
and keep it pressed while moving the
head rests as far down into the seat rests as possible until the safety button audibly latches.
WARNING■ The head restraints must be correctly adjusted in order to offer effective
protection for the occupants in the event of an accident.■
Never drive with the head restraints removed - risk of injury.
■
If the rear seats are occupied, the rear head restraint must not be in the
lower position.
CAUTION
The head restraints are integrated into the seat backrests and cannot be adjus-
ted.
Luggage compartment
Introduction
This chapter contains information on the following subjects:
Class N1 vehicles
47
Lashing eyes
47
Bag hooks
47
Fixing nets
48
Luggage compartment cover
48
Variable loading floor
49
Please observe the following for the purpose of maintaining good handling char-
acteristics of your vehicle:
›
Distribute loads as evenly as possible.
›
Place heavy objects as far forward as possible.
›
Attach the items of luggage to the lashing eyes or using the fixing net » page 47 .
In the event of an accident, even small and light objects gain so much kinetic en-
ergy that they can cause severe injuries.
The magnitude of the kinetic energy is dependent on the speed at which the ve-
hicle is travelling and the weight of the object.
Example: In the event of a frontal collision at a speed of 50 km/h, an object with a
weight of 4.5 kg produces an energy, which corresponds to 20 times its own
weight. This means that it results in a weight of approx. 90 kg “ ”.
Luggage compartment light
The light switches on/off when the luggage compartment lid is opened or closed.WARNING■ Store the objects in the luggage compartment and attach them to the lash-
ing eyes.■
Loose objects in the passenger compartment can be thrown forward during
a sudden manoeuvre or in case of an accident and can injure the occupants or
other oncoming traffic. This risk is still increased, if the objects which are fly-
ing around are hit by a deployed airbag. In this case, objects that are thrown
back may injure the occupants – risk to life.
■
Please note that transporting heavy objects alters the handling properties
of the vehicle due to the displacement of the centre of gravity – risk of acci-
dent! The speed and style of driving must be adjusted accordingly.
■
If the items of luggage or objects are attached to the lashing eyes with un-
suitable or damaged lashing straps, injuries can occur in the event of braking
manoeuvres or accidents. To prevent items of luggage from being thrown for-
ward, always use suitable lashing straps which must be firmly attached to the
lashing eyes.
■
The transported items must be stowed in such a way that no objects are
able to slip forward on sudden driving or braking manoeuvres – risk of injury!
■
When transporting fastened objects which are sharp and dangerous in the
luggage compartment that has been enlarged by folding the rear seats for-
ward, ensure the safety of the passengers transported on the other rear
seats » page 92 , Correct seated position for the passengers in the rear
seats .
■
If the rear seat next to the folded forward seat is occupied, ensure maxi-
mum safety, e.g. by placing the goods to be transported in such a way that the
seat is prevented from folding back in case of a rear collision.
■
Never drive with the luggage compartment lid open or ajar, as otherwise ex-
haust gases may get into the interior of the vehicle – risk of poisoning!
46Using the system
Page 51 of 176
Fixing netsFig. 42
Fixing nets/fastening details in the rear area of the luggage com-
partment
Fig. 43
Fixing nets: Details of the fastening behind the rear seats
First read and observe the introductory information and safety warn-
ings
on page 46.
Fixing examples for a fixing net as a horizontal pocket » Fig. 42 -
.
Details of the fastening in the rear area of the luggage compartment » Fig. 42 -
.
Details of the fastening for the fixing net to the upper lashing eyes behind the
foldable rear seatrest » Fig. 43 -
.
Details of the fastening for the fixing net to the lashing eyes on the luggage com-
partment floor behind the rear seats » Fig. 43 -
.
CAUTIONDo not place any sharp objects in the nets – risk of net damage.
Luggage compartment cover
Fig. 44
Removing/installing the luggage
compartment cover
First read and observe the introductory information and safety warn-
ings on page 46.
The luggage compartment cover can be removed if you wish to transport bulky
goods.
Folding up/folding down
›
To fold up, raise the luggage compartment cover and press into the side holders
1
» Fig. 44 .
›
To fold down, pull the raised part of the luggage compartment cover to the rear.
Removing/installing
›
To remove, move the luggage compartment downwards from the side holders
2
» Fig. 44 .
›
To re-install it, place the luggage compartment cover on the side holders
2
and
press on them from above into the holders
2
.
WARNING■ No objects should be placed on the luggage compartment cover, the vehicle
occupants could be endangered if there is sudden braking or the vehicle col-
lides with something.■
Never drive while the luggage compartment cover is raised. Always fold it
down before your journey, or remove it.
48Using the system
Page 52 of 176
CAUTIONMake sure that the luggage compartment cover is correctly engaged in the sideholders 2 » Fig. 44 - risk of damage to luggage compartment cover/luggage
compartment.
Variable loading floor
Fig. 45
Variable loading floor: open / fold
Fig. 46
Enlarge luggage compartment: down / forward
First read and observe the introductory information and safety warn-
ings
on page 46.
Open/close
›
Grasp the load floor at handle
1
and raise to the stop in the direction of the
arrow » Fig. 45 .
›
Close the load floor against the direction of the arrow.
Expanding luggage compartment downwards›Lift the load floor and push into the grooves » Fig. 46 - .›
Place the load floor on the base of the luggage compartment.
Expanding luggage compartment forwards
›
Remove the boot cover » page 48.
›
Remove the rear head restraints » page 45.
›
Fold the rear seat backrests forward » page 45.
Roof rack system
Introduction
This chapter contains information on the following subjects:
fixing points for base support
50
Roof load
50WARNING■ The transported items on the roof rack must be securely attached – risk of
accident!■
Always secure the load with appropriate and undamaged lashing straps or
tensioning straps.
■
Distribute the load evenly over the roof rack system.
■
Transporting heavy or large objects on the roof rack alters the handling
properties of the vehicle due to the displacement of the centre of gravity or
the increased wind exposure area – risk of accident! The style of driving and
speed must therefore be adapted to the current circumstances.
■
Avoid abrupt and sudden driving/braking manoeuvres.
■
Adjust the speed and driving style to the visibility, weather, road and traffic
conditions.
■
The permissible roof load, permissible axle loads and permissible total vehi-
cle weight must not be exceeded under any circumstances – risk of accident!
CAUTION
■ Only use roof rack systems approved by ŠKODA AUTO a.s.■When dealing with roof racks, the installation instructions supplied with the
roof luggage rack system must be observed. 49Seats and stowing
Page 54 of 176
Cup holderFig. 48
Centre console: Cup holder at the front/rear
First read and observe the introductory information and safety warn- ings
on page 50.
The cup holder is located in the front » Fig. 48 -
and rear » Fig. 48 -
of the
centre console.
Fixing cups in the front cup holder
Fold the cup holder clip » Fig. 48 -
towards the front.
Place the cup into the cup holder so that the cup holder clip surrounds the cup securely.
WARNING■ Never put hot beverage containers in the cup holder. If the vehicle moves,
they may spill – risk of scalding!■
No objects should be placed in the drinks holders, as the vehicle occupants
could be endangered if sudden braking occurs or the vehicle collides with
something.
■
Do not use any cups or beakers which are made of brittle material (e.g. glass,
porcelain). This could lead to injuries in the event of an accident.
CAUTION
Do not leave open beverage containers in the cup holder during the journey.
There is a risk of spilling e.g. when braking which may cause damage to the elec-
trical components or seat upholstery.
Ash trayFig. 49
Front centre console: Ashtrays
First read and observe the introductory information and safety warn-
ings on page 50.
The ashtray can be used for discarding ash, cigarettes, cigars and the like » .
Open/close
›
To open, raise the cover of the ash tray in the direction of the arrow » Fig. 49.
›
To close, press the cover of the ash tray fully downwards.
Removing
›
Pull out the ashtray upwards » .
Installing
›
Insert the ashtray vertically.
WARNINGNever place flammable objects in the ashtray – risk of fire!
CAUTION
When removing, do not hold the ashtray at the cover – risk of breakage.
51Seats and stowing
Page 58 of 176
Overview of the stowage compartment:Opening lever
Glasses storage box
Notepad holder
Pen holder
Coin holder
Card holderWARNINGThe storage compartment must always be closed when driving for safety rea-
sons.
Bag holder
Fig. 56
Dash panel: folding hooks
First read and observe the introductory information and safety warn-
ings on page 53.
There is a foldable hook in the opening lever of the storage compartment on the
front passenger's side » Fig. 56, which is used to suspend smaller items of lug-
gage, e.g. bags, etc.
CAUTION
■ The maximum permissible load of the hook is 1.5 kg.■When the hook is folded forward, it folds back automatically when the storage
compartment is opened.■
We recommend detaching suspended luggage from the hook before the stor-
age compartment lid is opened.
123456Photo holderFig. 57
Dash panel: Photo holder
First read and observe the introductory information and safety warn- ings on page 53.
The middle part of the dashboard has a holder » Fig. 57which is used to fasten
e.g. photos, notes, etc.
CAUTION
Do not damage the holders when handling them.
Storage compartment in the front centre console
Fig. 58
Front centre console: Stowage
compartment
First read and observe the introductory information and safety warn-
ings on page 53.
The open stowage compartment in the centre console » Fig. 58.
55Seats and stowing