buttons SUBARU FORESTER 2007 SG / 2.G Owners Manual

1-20 Seat, seatbelt and SRS airbags
Seatbelt extender
If the front seatbelts are not long enough
to permit the tongue plate to engage with
the seatbelt buckle, an optional seatbelt
extender is available from your SUBARU
dealer. When ordering an extender, only
order one particularly designed for your
vehicle. Several different types of extend-
ers are available to match various variet-
ies of front seatbelt designs. See your
SUBARU dealer for assistance.
The extender adds approximately 8 inch-
es (200 mm) of length and it can be used
for either the driver or front passenger
seating position.
For the safety of others, the extender
should be removed after each use, espe-
cially if the next person using the seatbelt
does not need one.
Note that leaving the seatbelt extender’s
tongue plate engaged with the seatbelt
buckle may prevent the Subaru advanced
front airbag system from functioning cor-
rectly or cause the system to fail.
NOTE
When the seatbelt extender is used by a pregnant passenger, consult a doctor
to get approval in advance.
To connect the extender to the seatbelt,
insert the tongue plate into the seatbelt
buckle so that the “PRESS” signs on the
buckle-release buttons of the extender
and the seatbelt are both facing outward
as shown in the diagram. You will hear a
click when the tongue plate locks into the
buckle.
When releasing the seatbelt, press on the
buckle-release button on the extender, not
on the seatbelt. This helps to prevent
damage to the vehicle interior and extend-
er itself.
Be sure to observe the following
when using the seatbelt extender.
Failure to follow these instructions
and warnings could reduce the ef-
fectiveness of the seatbelt and re-
sult in more serious injury in the
event of a collision.
y
Never use the extender when the
belt itself is long enough to permit
it to be buckled properly. If remov-
al of heavy clothing is all that is
needed to permit the seatbelt to
be buckled properly, remove the
heavy clothing and do not use the
extender.
yDo not use the extender if the
buckle of the extender rests over
the abdomen.
yDo not let someone else use the
extender. Use of an extender
when it is not needed could re-
duce the effectiveness of the seat-
belt and result in more serious in-
jury in the event of a collision.
yUse the extender only for the front
seatbelts and only for the model
for which it was originally provid-
ed. Never use the extender for the
rear seatbelts or for a different
model.
100605

4-8 Climate control
Automatic climate control
system (if equipped)
Although this climate control system can
be used as a full-automatic climate control
system, it can also, if desired, be used as
a semi-automatic climate control system.
When it is used as a full-automatic climate
control system, the outlet air temperature,
fan speed, air flow distribution, air inlet
control, and air conditioner compressor
operation are all automatically controlled
to maintain a constant, comfortable tem-
perature inside the vehicle.
NOTE yOperate the automatic climate con-
trol system when the engine is run-
ning. y When the engine coolant is cold, the
blower does not run. y In the “AUTO” mode, when the air
temperature in the passenger compart-
ment is sufficiently cool, the air condi-
tioner compressor does not operate.
For efficient defogging or dehumidify-
ing in cold weather, press the “A/C”
button to operate the air conditioner
compressor. y Even when cooling is not necessary,
setting the temperature much lower
than the current outlet air temperature turns on the air conditioner compres-
sor automatically and the “A/C” indica-
tor light on the control panel comes on.
„ Control panel
1) Temperature control dial
2) Fan speed control dial
3) Air flow control dial
4) Rear window defogger button (Refer to the “Rear window defogger button” in
chapter 3.)
5) Air inlet selection button
6) Air conditioner button
„ To use as full-automatic cli-
mate control system
Place the temperature control dial in the
position for your desired temperature, then set the other dials and buttons as de-
scribed in the following. The system’s
functions will then switch to AUTO mode
and be controlled automatically. y
Air flow control dial: AUTO position
y Fan speed control dial: AUTO position
y Air inlet selection button: Press for at
least 1 second. (Indicator will flash twice.) y Air conditioner button: Press for at least
1 second. (Indicator will flash twice.)
„ To use as semi-automatic cli-
mate control system
Each function can be individually set to
AUTO mode independently of the others.
Any function set to AUTO mode is con-
trolled automatically. Any function not set
to AUTO mode can be manually adjusted
as desired.
The temperature can be set within a range
of 65 to 85 qF (20 to 30 qC).
3
5 4
6 2
1
400594

5-4 Audio
Type A audio set (if equipped)
The radio will operate only when the ignition switch is in the “ACC” or “ON” position. „Radio operation
500258
(1) (2)
(3)
(4)
(5)
(6)
(1) Power switch, Volume control, Tone/
Fader/Balance control dial
(2) BAND button
(3) Tuning buttons
(4) Preset buttons
(5) AUDIO button
(6) SCAN button T Power switch and volume/bass/tre-
ble/fader/balance control (PWR/ VOL)
The dial (1) is used for both power (ON/
OFF) and volume control. The radio is
turned ON and OFF by pushing the dial
and the volume is controlled by turning the
dial. V Tone and balance control
The “VOLUME” control knob normally
function as volume control. This knob be-
come a control for Treble, Bass, Fader or
Balance when you select the appropriate
audio mode.
Choose desired volume level for each
mode by turning the “VOLUME” control
knob. The control function returns to vol-
ume control mode after approximately 5
seconds.
To change control modes: Each brief
press of the “AUDIO” button changes con-
trol modes in the following sequence start-
ing from volume control mode. (When the

5-6 Audio
TFM/AM band selection button
(BAND)
Push the “BAND” button when the radio is
on to select FM1, FM2 or AM band recep-
tion. Each time this button is pressed, the
band will change in the following order:
The display indicates which one is cur-
rently selected. T Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received. T Tuning (TUNE)
V Manual tuning (TUNE)
Push the “ ” side of the tuning button
(3) to increase the tuning frequency and
press the “ ” side of the button to de-
crease it.
Each time the button is pressed, the fre-
quency changes 10 KHz in the AM wave-
band and 0.2 MHz in the FM waveband. T Seek tuning
If the tuning button (3) is pressed for long-
er than half of a second, the radio will be-
gin to automatically search for receivable frequencies and will stop at the first one
found. This function may not be available,
however, when radio signals are weak. In
such a situation, perform manual tuning to
select the desired station. T
Automatic tuning (SCAN)
Press the “SCAN” button (6) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at the
station for five seconds while displaying
the frequency, after which scanning will
continue until the entire band has been
scanned from the low end to the high end.
Press the “SCAN” button again to cancel
the SCAN mode and to stop on any dis-
played frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only.
Automatic tuning may not function proper-
ly if the station reception is weakened by
distance from the station or proximity to
tall buildings and hills. T Selecting preset stations
Presetting a station with a preset button
(4) allows you to select that station in a
single operation. Up to six AM, FM1 and
FM2 stations each may be preset. T
How to preset stations
1. Press the “BAND” selection button to
select AM, FM1 or FM2 reception.
2. Press the “SCAN” button (6) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (4) for
at least 2 seconds to store the frequency.
At this time, there will momentarily be no
sound from the radio. If the button is
pressed for less than 2 seconds, the pre-
ceding selection will remain in memory.
NOTE
y If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons. y If a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when it receives calls. This noise
does not indicate a radio fault.
FM1 FM2 AM

Audio 5-9
– CONTINUED –
„CD changer control (if optional in-dash CD changer is connect- ed)
An optional CD changer can be connected to this audio unit. Consult the instructions that
accompany the CD changer for operating the CD changer itself (e.g., how to load or un-
load CDs). See your SUBARU dealer for more information.
500260
(16)
(17)
(18)
(19)
(20)
(16) CD button
(17) Track selection buttons
(18) RAND (Random) button
(19) RPT (Repeat) button
(20) SCAN button T To start playback
When the “CD” button (16) is pressed, the
CD changer will start playback. The dis-
play shows the current disc number, track
number and the elapsed time during play-
back.
NOTE
y If a disc is in the player, the “DISC”
button is used to change from CD play-
er operation to DISC changer opera-
tion. Each time the “DISC” button is
pressed, the operating mode will
change alternately. y At the end of the disc, the player au-
tomatically continues with the next
disc. y After playback on the last disc finish-
es, playback will automatically return
to the first disc. y If you have loaded fewer than 6
discs, any missing disc is automatical-
ly skipped. T Selection of a desired disc
You can select a desired disc from among

5-10 Audio
the discs contained in the CD changer
only by pressing the corresponding num-
ber on one of the disc select buttons. If
you are to listen to the 5th disc in the CD
changer, press the “5” button of the disc
select buttons. All other discs in the CD
changer can also be selected in a similar
way.
NOTE yNo disc change takes place if the
button corresponding to the storage
tray in which no disc is loaded is
pressed. y If the disc select button correspond-
ing to the disc now in playback is
pressed again, the disc will be replayed
from its beginning. T To select a song from its beginning
V Forward direction
Briefly press the “ ” side of the button
(17) to skip to the beginning of the next
track. Each time this side of the button is
pressed, the indicated track number will
increase. V Backward direction
Briefly press the “ ” side of the button
(17) to skip to the beginning of the current
track. Each time this side of the button is
pressed, the indicated track number will decrease. T
Fast-forwarding and fast-reversing
V Fast-forwarding
Press the “ ” side of the button (17)
continuously to fast-forward the disc.
Release the button to stop fast-forward-
ing.
If you continue fast-forwarding to the end
of the disc, the CD changer will automati-
cally stop fast-forwarding and start play-
back beginning with the first track on the
current disc. V Fast-reversing
Press the “ ” side of the button (17)
continuously to fast-reverse the disc.
Release the button to stop fast-reversing.
If you continue fast-reversing to the begin-
ning of the disc, the CD changer will auto-
matically stop fast-reversing and start
playback beginning with the first track on
the current disc. T Repeat playback
Press the “RPT” button (19) while a song
is playing to play the song repeatedly. The
“RPT” indicator will come on and the song
will be played continuously. To cancel the
repeat mode, press the button again.
Then the “RPT” indicator goes out, and
normal playback mode is restored. T
Random playback
Press the “RAND” button (18) while a disc
is being played back to play all songs on
the disc in a random order. The “RAND”
indicator will come on and all songs on the
disc will be played in a random order.
To cancel the random mode, press the
button again. Then the “RAND” indicator
goes out, and normal playback mode is
restored. T Scan (a convenient way to become
familiar with a disc)
1. Press the “SCAN” button (20). – The display shows “SCAN” and the
track number being scanned.
– You hear the first 10 seconds of each
track.
– The operation is automatically
cleared after playing all programs.
Then, normal playback starts.
2. Press the “SCAN” button again when
you hear a track you like. – Normal playback resumes.
T To stop playback
To stop playback and switch over to the
radio mode, press the “BAND” button.

Audio 5-11
– CONTINUED –
Type B audio set (if equipped)
The audio set will operate only when the ignition switch is in the “ACC” or “ON” position. „Radio operation
500325
(1) (2) (4)
(3) (5)
(6)
(1) Power switch, Volume, Brightness control dial
(2) FM/AM selection button
(3) Seek button
(4) Scan button
(5) Sound/Tune control dial
(6) Preset buttons T Power switch and volume/bright-
ness control (POWER/VOL/BRIGHT)
The dial (1) is used for both power (ON/
OFF) and volume control. The radio is
turned ON and OFF by pushing the dial,
and the volume is controlled by turning the
dial. T Sound control and tune/folder se-
lect/channel control (SOUND/TUNE/
FOLDER/CH)
The dial (5) is used for selecting the sound
control mode with each brief press of the
dial, and for adjusting each level by turn-
ing it. It is also used for tuning the radio/
folder selection (only when playing MP3 or
WMA)/channel selection (satellite radio*)
when the “FM/AM”, “CD/AUX” and “SAT”
are selected.
(*: Use of satellite radio (Sirius) requires a
tuner, antenna and a service contract. For
details, please contact your SUBARU
dealer.)

Audio 5-13
– CONTINUED –
V
Display illumination dimness can-
cellation (BRIGHT)
The brightness of the radio display dims
when the light switch is in the “ ” or
“ ” position. If this makes the display
difficult to read, press the volume dial for
more than 2 seconds to return the display
to original brightness. Subsequently
pressing the volume dial again for more
than 2 seconds or if you can safely do so,
turning the light switch to the OFF position
and back to the “ ” or “ ” posi-
tion makes the radio display dim again. T FM/AM selection button (FM/AM)
Push the “FM/AM” button (2) when the ra-
dio is on to select FM1, FM2 or AM recep-
tion. Each time this button is pressed, the
band will change in the following order:
The display indicates which one is cur-
rently selected. T
Stereo indicator
The stereo indicator “ST” will come on
when an FM stereo broadcast is received. T Manual tuning (TUNE)
Turn the tuning dial (5) clockwise to in-
crease the tuning frequency and turn the
dial counterclockwise to decrease it. Each
click the dial is turned, the frequency
changes 10 kHz in the AM waveband and
0.2 MHz in the FM waveband. T Seek tuning
When the “ ” side of the “SEEK/
TRACK/CAT” button (3) is depressed, the
radio will begin to automatically seek up
for receivable frequencies and will stop at
the first one found. For the “ ” side, the
radio will begin to automatically seek
down. This function may not be available,
however, when radio signals are weak. In
such a situation, perform manual tuning to
select the desired station. T Automatic tuning (SCAN)
Press the “SCAN” button (4) to change the
radio to the SCAN mode. In this mode, the
radio scans through the radio band until a
station is found. The radio will stop at a re-
ceivable station for 5 seconds while dis-
playing the frequency by blinking, after
which scanning will continue until the en-
tire band has been scanned from the low end to the high end. Press the “SCAN”
button again to cancel the SCAN mode
and to stop on any displayed frequency.
When the “SCAN” button is pressed for
automatic tuning, stations are scanned in
the direction of low frequencies to high fre-
quencies only. Automatic tuning may not
function properly if the station reception is
weakened by distance from the station or
proximity to tall buildings and hills. T
Selecting preset stations
Presetting a station with a preset button
(6) allows you to select that station in a
single operation. Up to six AM, FM1 and
FM2 stations each may be preset. T How to preset stations
1. Press the “FM/AM” button (2) to select
AM, FM1 or FM2 reception.
2. Press the "SCAN" button (4) or tune
the radio manually until the desired station
frequency is displayed.
3. Press one of the preset buttons (6) for
at least 2 seconds to store the frequency.
The frequency of the station will flash
once on the display at this time.
NOTE
y If the connection between the radio
and battery is broken for any reason
such as vehicle maintenance or radio
removal, all stations stored in the pre-
BALANCE
BASS
FADER TREBLE
MIDDLE
FM1 FM2 AM

5-14 Audio
set buttons are cleared. If this occurs,
it is necessary to reset the preset but-
tons. yIf a cell phone is placed near the ra-
dio, it may cause the radio to emit
noise when the phone receives calls.
This noise does not indicate a problem
with the radio.

Audio 5-15
– CONTINUED –
„Built-in CD changer control
500323
(7) (8) (9) (12) (11)
(10) (14) (13)
(15)
(16)
(7) CD button
(8) Eject button
(9) Disc slot
(10) Track selection buttons
(11) Repeat/Random button
(12) Disc number indicator
(13) Load button
(14) Folder selection dial
(15) Disc selection buttons
(16) Display button
NOTE y Make sure to always insert a disc
with the label side up. If a disc is insert-
ed with the label side down, it might be
ejected or the player might shut off. y If a disc is inserted during a radio
broadcast, the disc will interrupt the
broadcast. y The player is designed to be able to
play music CD-Rs and music CD-RWs,
but it may not be able to play certain
ones. y 8 cm/3 inch CDs are not supported,
and if inserted, they will be immediate-
ly ejected.