oil SUZUKI ALTO 2021 Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2021, Model line: ALTO, Model: SUZUKI ALTO 2021Pages: 139, PDF Size: 2.22 MB
Page 3 of 139
359K,76G,844-74EFOREWORDThis manual is an essential part of yourvehicle and should be kept with the vehicle
at all times. Please read this manualcarefully and review it from time to time. Itcontains important information on
maintenance. It is especially important thatthis manual remain with the vehicle at thetime of resale. The next owner will need thisinformation also.
You are invited to avail the three freeinspection services as described in this
manual. Three free inspection coupons areattached to this manual. Please show thismanual to your dealer when you take your
vehicle for any Service.
To prolong the life of your vehicle andreduce mainte nance costs, the periodic
maintenance must be carried out according to the "PERIODIC MAINTENANCESCHEDULE" described in "INSPECTION
AND MAINTENANCE" section of thismanual. Periodic maintenance is essentialfor preventing trouble and accidents toensure your satisfaction and safety.
Daily Inspection and Care as per "DAILYINSPECTION CHECKLIST" described in the
"INSPECTION AND MAINTENANCE"section of this Manual is essential forprolonging the operating life of the vehicleand for safe driving.
All information in this manual is
based on the latest product
information available at the time of
publication. Due to improvements or
other changes, there may be
discrepancies between information
in this manual and your vehicle.
MARUTI SUZUKI reserves the right
to make changes at any time
without notice.
This vehicle may not comply with
standards or regulations of other
countries. Before attempting to
register this vehicle in any other
country, check all applicable
regulations and make any
necessary modifications.
IMPORTANTWARNING/CAUTION/NOTEPlease read this manual and follow its
instructions carefully. To emphasise specialinformation, the words WARNING,CAUTION, and NOTE have specialmeanings. Information following these signal
words should be carefully reviewed.The personal safety of the driver,
passengers, or bystanders may be
involved. Disregarding this information
could result in their injury or death.
These instructions point out special
service procedures or precautions
that must be followed to avoid
damaging the vehicle.
CAUTION
MARUTI SUZUKI INDIA LIMITED believes in conservation and protection of Earth's
natural resources.
To that end, we encourage every vehicleowner to recycle, trade in, or properlydispose of, as appropriate, used motor oil,coolant, and other fluids; batteries; andtyres.MARUTI SUZUKI INDIA LIMITED
0-1
ww ww
w WARNING
NOTE :
This provides special information to makemaintenance easier or important instructionsclearer.
Page 7 of 139
759K,76G,844-74E
2
WARRANTY POLICYMaruti Suzuki India Limited (hereinafter called “Maruti Suzuki”)\
,
warrants that each new Maruti Suzuki vehicle distributed in India
by Maruti Suzuki and sold by an authorised Maruti Suzuki dealer
will be free, under normal use and service, from any defects in
material and workmanship at the time of manufacture SUBJECT
TO THE FOLLOWING TERMS AND CONDITIONS:
(1) Qualification:To qualify for this warranty:
(a) The Maruti Suzuki vehicle must be delivered by Maruti Suzuki authorised dealer and set-up, serviced by Maruti
Suzuki authorised dealer/service station.
(b) The warranty registration card in respect of each vehicle must be completed by the dealer at the time of delivery
of the vehicle and dealer should retain the same.
(2) Term: The term of the warranty shall be twenty four (24) monthsor 40,000 kilometers (whichever occurs first) from the date
of delivery to the first owner.
(3) Maruti Suzuki Warranty Obligation: If any defect(s) should be found in a Maruti Suzuki vehiclewithin the term stipulated above, Maruti Suzuki only obligation
is to repair or replace at its sole discretion any part shown
to be defective, with a new part or the equivalent at no cost
to the owner for parts or labour, when Maruti Suzuki
acknowledges that such a defect is attributable to faulty material
or workmanship at the time of manufacture. The owner is
responsible for any repair or replacements which are not covered by this warranty.
(4) Limitation:
This warranty shall not apply to:
(a) normal maintenance service required other than the three free services, including without limitation, oil and fluid
changes, headlight aiming, fastener retightening, wheel
balancing, wheel alignment and tyre rotation, cleaning of
injectors, adjustments of carburettor, ignition timing, clutch
and valve clearance.
(b) the replacement of normal wear parts including without limitation, bulbs, battery, tyres and tubes, spark plugs, belts,
hoses, filters, wiper blades, brushes, contact points, fuses,
clutch disc, brake shoes, brake pads, cable and all rubber
parts (except oil seal and glass run).
(c) any vehicle which has been used for competition or racing.
(d) any repairs or replacement required as a result of accidents or collision.
(e) any defects caused by misuse, negligence, abnormal use or insufficient care.
(f) any vehicle which has been modified or altered, including without limitation, the installation of performance
accessories.
(g) any vehicle on which parts or accessories not approved by Maruti Suzuki have been used.
(h) any vehicle which has not been operated in accordance
with the operating instructions in the Maruti Suzuki Owner’s
Manual.
(i) any vehicle which has not received, during the warranty term, the service inspections prescribed in the Maruti
Suzuki Owner’s Manual.
(j) any vehicle which has been assembled, disassembled,
WARRANTY POLICY
2-1
Page 9 of 139
959K,76G,844-74E
Maruti Suzuki offers the Emission Warranty on all Maruti Suzuki vehicles\
(apart from the Regular warranty and will run parallelto the regular product warranty) only in four metropolitan cities (New Delhi, Kolkata, Mumbai and Chennai) with effect from
July 1st, 2001.
Terms:
The Emission Warranty will be applicable for 80,000 kms or 3 years (Which ever comes earlier) from the date of delivery to
the first owner. The remaining warranty terms will be valid in case of a\
ny change in ownership provided the production of all
valid document.
Conditions:1. Under Emission Warranty, Warranty claims will be admitted for a prima fa\
cie examination, in case vehicle fails to meet to the Emission Standard as specified in sub rule (2) of rule no. 115 of Cent\
ral Motor Vehicles Rules (CMVR), 1989.
2. The warranty claims will only be accepted after examination carried out \
by Maruti Suzuki or it's dealer which leads to firm c onclusions
that the
a) Original settings have not been tempered in any case.
b) Part (as given in Annexure-A) has a manufacturing defect.
c) Vehicle is unable to meet the Emission Standards (as given in 1.), ins\
pite of the vehicle having been maintained and used in accordance with the instructions as specified in Owner's Manual and S\
ervice Booklet and the used fuel and different oils
(Engine oil, Transmission oil, Brake oil etc.) are also as per specifi\
cation.
3. The method of examination for deciding the warranty of the parts will be\
at the sole discretion of Maruti Suzuki and it's dea ler
and results of the examination will be final and binding. If after exami\
nation, the warrantable condition is not established, M aruti
Suzuki and it's dealer has the right to charge all, or part of the cost \
of such examination.
4. Under Emission Warranty, the parts (as given in Annexure-A) will be ch\
anged free of cost, but the consumables will be charged as per actual.
5. If the part covered under Emission Warranty or the associated parts, are\
not independently replaceable, on account of these b eing
integral parts a complete assembly, Maruti Suzuki and it's dealer will h\
ave the sole discretion to replace entire assembly or b y
using some of the parts of the system through suitable repair or modific\
ations.
EMISSION WARRANTY
2-3
Page 10 of 139
10
59K,76G,844-74E
6. Any consequential repairs or replacement of parts which may be found nec\
essary to establish compliance of Emission Warranty,will not be considered under warranty, unless the same is under product \
warranty. The consumable will be charged as per actual
under such repair or replacement.
7. Maruti Suzuki will not be responsible for the cost of transportation of \
the vehicle to the nearest Maruti Suzuki dealer works hop
or any loss due to non-availability of the vehicle during the period of \
lodging of a warranty claim and examination and/or repa ir
by Maruti Suzuki dealer.
8. Maruti Suzuki will not be responsible for any penalty that may be charge\
d by statutory authorities on account of failure to c omply
with the EMISSION STANDARDS.
9. Emission Warranty will not be affected on the change of owner, provided \
all the documents are available.
10. All maintenance actions (as specified in the Owner's Manual and Service\
Booklet) need to be followed and recorded in the man ual
for emission warranty.
11. The customer needs to produce the PUC (Pollution Under Control) certif\
icate valid for the period preceding the test during w hich
the failure is discovered. The receipts (for the maintenance of the veh\
icle as per specification in Owner's Manual and Service
Booklet from the date of original purchase of the vehicle) will also be\
required.Condition Under which the Emission Warranty is not APPLICABLE
1. In the absence of valid PUC certificate.
2. Vehicle not serviced from Maruti Suzuki authorised workshop as per the s\
chedule specified in the Owner's Manual.
3. Vehicle subjected to abnormal use (accident, motor race, rallies or for\
the purpose of establishing the records etc.)
4. Use of non MGP (Maruti Genuine Part).
5. Vehicle tempered in an unauthorised manner.
6. Tampering with odometer so that the actual kilometer reading can not be \
read.
7. Use of adulterated fuel and/or unspecified oils (Engine oil, Transmissi\
on oil and Brake oil etc.)EMISSION WARRANTY
2-4
Page 11 of 139
1159K,76G,844-74E
Annexure-A
List of parts covered under Emission Warranty
1. Fuel injection Assembly, Pressure Regulator, Throttle Body Assembly.
2. Electronic Control Module (ECM).
3. Intake Manifold.
4. EGR valve.
5. Distributor and internal parts.
6. Ignitions coil.
7. Canister Assembly.
8. Vapour Liquid Separator.
9. Fuel Tank and Filler Cap.
10. PCV (Positive Crankcase Ventilation) Valve.
11. Oil Filler Cap.
12. Catalytic Convertor.
13. Exhaust manifold.
14. All fuel injection System related SENSORS.
15. Maniverter
EMISSION WARRANTY2-5
Page 24 of 139
2576G-74E
BEFORE DRIVING
3-12
Never use the same seat belt onmore than one occupant and never
attach a seat belt over an infant or
child being held on an occupant’s
lap. Such seat belt use could cause
serious injury in the event of an
accident.
Pregnant women should use seat belts, although specific recommen-
dations about restraint use should
be made by the woman’s medical
advisor. Remember that the lap
portion of the belt should be worn
as low as possible across the hips,
as shown in the diagram.
ww ww
w WARNING
VV
VV
V
VV
VV
V
76G-03-029
Periodically inspect seat belt
assemblies for excessive wear and
damage. Seat belts should be
replaced if webbing becomes frayed,
contaminated, or damaged in any
way. It is essential to replace the
entire seat belt assembly after it has
been stressed in an impact, even if
damage to the assembly is not
obvious.
Infants and small children should never be transported unless they are
properly restrained. Restraint
systems for infants and small
children can be purchased locally
and should be used. Make sure that
the system you purchase meets
applicable safety standards. Read
and follow all the directions
provided by the manufacturer.
Avoid contamination of seat belt webbing by polishes, oils,
chemicals, and particularly battery
acid. Cleaning may safely be carried
out using mild soap and water.
For children, if the shoulder belt irritates the neck or face, move the
child closer to the center of the
vehicle.
ww ww
w WARNING
VV
VV
V
VV
VV
V
Be sure to inspect all seat belt
assemblies after any collision. Any
seat belt assembly which was in use
during a collision (other than a very
minor one) should be replaced, even
if damage to the assembly is not
obvious. Any seat belt assembly
which was not in use during a
collision should be replaced if it does
not function properly or is damaged
in any way.
ww ww
w WARNING
VV
VV
V
Page 41 of 139
42
76G-74E
INSTRUMENT PANEL
If you operate the engine with thislight on, severe engine damage can
result.
Do not rely on the Oil Pressure Light to indicate the need to add oil.
Be sure to periodically check the
engine oil level (see section
"INSPECTION & MANINTENANCE").
5-5
CAUTION
Charging Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and
remain on if there is something wrong with
the battery charging system. If the light
comes on when the engine is running, the
charging system should be inspected
immediately by your MARUTI SUZUKI
dealer.
Do not continue driving long with the
charging light ON as this will drain the
battery 'dead'.
CAUTION
76G-05-007 76G-05-008
EXAMPLE
Oil Pressure Light
This light comes on when the ignition switch
is turned on, and goes out when the engine
is started. The light will come on and
remain on if there is insufficient oil pressure.
If the light comes on when driving, pull off
the road as soon as you can and stop the
engine. Check the oil level and add oil if
necessary (see section "INSPECTION &
MAINTENANCE"). If there is enough oil, the
lubrication system should be inspected by
your MARUTI SUZUKI dealer before you
drive the vehicle again.
76G-05-006
Page 54 of 139
5576G-74E
INSTRUMENT PANEL
5-18
76G-05-051
(ALTO / ALTO K10)
Quick Cooling (Using recirculated air)
The lever/knob settings are the same as for
normal cooling except you move the air
intake lever to “RECIRCULATED AIR”. If
you use this cooling method for a extended
period of time, the air in the vehicle can
become contaminated. Therefore, you
should occasionally move the air intake
lever to “FRESH AIR”.NOTE: If your vehicle has been left in the sun with
the windows closed, it will cool faster if youopen the windows briefly while you operatethe air conditioner with the air intake leverat “FRESH AIR” and the fan at high speed.
Dehumidifying
Push in the A/C button, move the function
lever/knob to the desired function position,
the air intake lever to “FRESH AIR”, the
temperature control lever/knob to the desired
temperature position, and the fan switch to
the desired fan speed position.NOTE:
Because the air conditioner dehumidifies theair, turning it on will help keep the windowsclear, even when blowing heated air using
the DEMIST or HEATER & DEMISTfunctions.
76G-05-053
(ALTO / ALTO K10) Maintenance
If you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain op-
timum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine idling.
This circulates the refrigerant and oil and
helps protect the internal components.
Note:
Your vehicle uses the air conditioning re-frigerant HFC-134a, commonly called “R-134a”. Only R-134a should be used in your
vehicle.
CAUTION
Using the wrong refrigerant may dam-
age your air conditioning system. Use
R-134a only. Do not mix or replace the
R-134a with other refrigerants.
Page 69 of 139
70
76G-74E
EXHAUST GAS WARNING
with the engine running, make sure
the air intake lever is set to “FRESH
AIR” and the fan is at high speed.
Avoid operating the vehicle with the rearend door open. If it is necessary
to operate the vehicle with the
rearend door open, make sure all
the windows are closed and the fan
is at high speed with the air intake
lever set to "FRESH AIR".
To allow proper operation of your vehicle’s ventilation system, keep
the air inlet grille in front of the
windscreen clear of snow, leaves, or
other obstructions at all times.
Keep the exhaust tailpipe area clear of snow and other material to help
reduce the buildup of exhaust gases
under the vehicle. This is
particularly important when parked
in blizzard conditions.
Have the exhaust system inspected
periodically for damage and leaks.
Any damage or leaks should be
repaired immediately.
DAILY INSPECTION CHECKLIST
ww ww
w WARNING
7-1
ww
ww
w WARNING
Before driving:
1)
Make sure that windows, mirrors, lights,
and reflectors are clean and unobstructed.
2) Check the tyres.
3) Look for fluid and oil leaks.NOTE:
It is normal for water to drip from the air
conditioning system after use.4) Adjust the seat/head restraint.
5) Check the brake pedal and the parking brake lever.
6) Adjust the mirrors.
7) Make sure that you and passengers have properly fastened your seat belts.
8) Make sure that all warning lights come on as the key is turned to the “ON” or
“START” position.
9) Check all gauges.
10) Make sure that the brake fluid level warning light is off when the parking
brake is released with the engine
running.
OPERATING YOUR VEHICLEAvoid breathing exhaust gases.
Exhaust gases contain carbon
monoxide, a potentially lethal gas that
is colourless and odourless. Since
carbon monoxide is difficult to detect
by itself, be sure to take the following
precautions to help prevent carbon
monoxide from entering your vehicle.
Do not leave the engine running ingarages or other confined areas.
Do not park with the engine running for a long period of time, even in an
open area. If it is necessary to sit
for a short time in a parked vehicle
VV VV
V
VV
VV
V
76G-07-001 76G-07-002
Page 70 of 139
7176G-74E
Before starting the engine:
1) Make sure the parking brake is appliedfully.
2) Manual Transmission - Shift into “N” (neutral) and depress the clutch pedal all
the way to the floor. Hold it while starting
the engine.
Make sure that the parking brake is
applied fully and the transmission is
in Neutral before attempting to start
the engine.
Stop turning the starter immediately after the engine has started or the
starter system can be damaged.
Do not crank the engine for more than 15 seconds at a time. If the
engine doesn’t start on the first try,
wait about 15 seconds before trying
again.
7-2
STARTING THE ENGINE
ww ww
w WARNING
OPERATING YOUR VEHICLE
Once a week, or each time you fill your fuel
tank, perform the following under-bonnet
checks:
1) Engine oil level.
2) Coolant level.
3) Brake fluid level.
4) Windscreen washer fluid level.
5) Battery solution level.
6) Bonnet latch operation.
Pull the bonnet release handle inside the
vehicle. Make sure that you can not
open the hood all the way without
releasing the secondary latch. Be sure
to close the hood securely after checking
for proper operation. See "All Latches,
Hinges & Locks" of "PERIODIC
MAINTENANCE SCHEDULE" in the
"INSPECTION AND MAINTENANCE"
section for lubrication schedule.
Make sure the bonnet is fully closed
and latched before driving. If it is not,
it can fly up unexpectedly during
driving, obstructing your view and
resulting in an accident.
ww ww
w WARNING
Starting a Cold Engine
Engine which is started after 6 hours should
be treated as cold engine.
For Electronic fuel injection models
With your foot off the accelerator pedal,
crank the engine by turning the ignition
key to “START”. Release the key when
the engine starts.
If the engine does not start after 15 seconds of cranking, wait about 15
seconds, then press down the
accelerator pedal to 1/3 of its travel and
try cranking the engine again. Release
the key and accelerator pedal when the
engine starts.
If the engine still does not start, try holding the accelerator pedal all the way
to the floor while cranking. This should
clear the engine if it is flooded.
Starting a Warm Engine
For Electronic fuel injection models:
Use the same procedure as for “Starting a
Cold Engine”.
CAUTION