turn signal SUZUKI NEXA 2015 1.G Owners Manual
[x] Cancel search | Manufacturer: SUZUKI, Model Year: 2015, Model line: NEXA, Model: SUZUKI NEXA 2015 1.GPages: 288, PDF Size: 8.02 MB
Page 26 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
• If you lock the doors using the remote
controller when the engine hood is open,
the siren will sound 3 times to remind
you.• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
remote controller, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:
• The maximum operating distance of the
remote controller is about 5 m (16 ft.),
but this can vary depending on the sur-
roundings, especially near other trans-
mitting devices such as radio towers or
CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the remote controller if the ignition mode
is other than the LOCK (OFF).
• When any door is open, if you push the
“LOCK” button on the remote controller,the exterior buzzer will sound and doors
cannot be locked.
•
If you lose one of the remote controllers,
ask your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S as soon as possible for a
replacement. Be sure to have your
dealer program the new remote
controller code in your vehi-cle’s
memory so that the old code is
erased. 3 D Q L F D O D U P I X Q F W L R Q
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds. The turn signal lights will blink for
about 27.5 seconds. Also, the siren will
sound for about 27.5 seconds at the same
time.
To cancel the panic alarm, press any but-
ton (LOCK OR UNLOCK). You can also
change the ignition mode to ON to cancel
the panic alarm.
NOTE:
The panic alarm function will not activate
when the ignition mode is “ACC” or “ON”.
Page 27 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
. H \ O H V V X Q O R F N L Q J O R F N L Q J X V L Q J W K H
U H T X H V W V Z L W F K H V
64MS134
When the remote controller is within the
operating range described in this section,
you can lock or unlock the doors (including
the tailgate) by pushing the request switch
(1) on the driver’s door handle, front pas-
senger’s door handle or tailgate.
To lock all doors when all doors are
unlocked:
• To lock all doors, push one of the
request switches once.
The turn signal lights will flash once and
the siren will sound once when the doors
are locked.
To unlock a door or all doors:
• Push one of the request switches once
to unlock only one door.
• Push one of the request switches twice
to unlock all doors.NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren will sound twice.
• If the interior light switch is in the door
position, the interior light will turn on for
about 15 seconds and then fade out. If
you press the engine switch during this
time, the light will start to fade out imme-
diately.
Be sure the doors are locked after you
operate the request switch to lock the
doors.NOTE:
• If you lock the doors using the request
switch when the engine hood is open,
the siren will sound 3 times to remind
you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
request switch, the siren will sound 4
times to remind you. If this happens,
check whether your vehicle has been
broken into while you were away from it.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:• The door locks cannot be operated by
the request switch under the following
conditions:
– If any door is open or is not completely
closed.
– If the ignition mode is other than LOCK
(OFF).
• If no doors are opened within about 30
seconds after unlocking the doors by
pushing the request switch, the doors will
be locked again automatically.
(1)
( ; $ 0 3 / (
NOTICE
Page 31 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
Used batteries must be disposed properly
according to applicable rules or regulations
and must not be disposed with ordinary
household trash.
. H \ O H V V ( Q W U \ 6 \ V W H P 7 U D Q V P L W W H U
7 \ S H %
76MS011
(1) “Lock” button
(2) “Unlock” button
You can lock or unlock all doors (including
the tailgate) simultaneously by operating
the transmitter near the vehicle. & H Q W U D O G R R U O R F N L Q J V \ V W H P
• To lock all doors, push the “LOCK” but-
ton (1) once.
• To unlock only the driver’s door, push the
“UNLOCK” button (2) once.
• To unlock other doors, push the
“UNLOCK” button (2) once again.
NOTE:
You can switch the function that unlocks all
doors from twice operations to once opera-
tion, and vice versa, via the setting mode
of the information display. For details on
how to use the information display, refer to
“Information Display” in this section.
The turn signal lights will flash once and
the siren (if your vehicle is equipped with
the security system) will sound once when
the doors are locked.
When the doors are unlocked:
• The turn signal lights will flash twice and
the siren (if your vehicle is equipped with
the security system) will sound twice.
• If the interior light switch is in the
“DOOR” position, the interior light will
turn on for about 15 seconds and then
fade out. If you insert the key into the
ignition switch during this time, the light
will start to fade out immediately.
Be sure the doors are locked after you
operate the lock button (1).
NOTICE
7 K H U H P R W H F R Q W U R O O H U L V D V H Q V L W L Y H
H O H F W U R Q L F L Q V W U X P H Q W 7 R D Y R L G G D P
D J L Q J L W G R Q R W H [ S R V H L W W R G X V W R U
P R L V W X U H R U W D P S H U Z L W K L Q W H U Q D O S D U W V
(1)
(2)
Page 32 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
NOTE:
If no door is opened within about 30 sec-
onds after the unlock button (2) is oper-
ated, the doors will automatically lock
again.
NOTE:
(For models with security system)
• If you lock the doors using the transmit-
ter when the engine hood is open, the
siren will sound 3 times to remind you.
• If the security system was triggered due
to an unauthorized entry into the vehicle
and then you unlock the doors using the
transmitter, the siren will sound 4 times
to remind you. If this happens, check
whether your vehicle has been broken
into while you were away from it.
• Once you push both of the “LOCK” but-
ton (1) and “UNLOCK” button (2), then
you push one of the buttons within 5 sec-
onds, the siren will not sound. However,
If you push one of the buttons twice
within 5 seconds, or push one of the but-
tons 5 seconds later, the siren will
sound.
• You can set whether the siren sounds
when locking or unlocking the door(s) via
the setting mode of the information dis-
play. For details on how to use the infor-
mation display, refer to “Information
Display” in this section.NOTE:
• The maximum operating distance of the
keyless entry system transmitter is about
5 m (16 ft.), but this can vary depending
on the surroundings, especially near
other transmitting devices such as radio
towers or CB (Citizen’s Band) radios.
• The door locks cannot be operated with
the transmitter, if the ignition key is
inserted in the ignition switch.
• When any door is open, the door locks
can be operated only by unlocking with
the transmitter. With this unlocking oper-
ation, the turn signal lights will flash
twice and the siren (if your vehicle is
equipped with the security system) will
sound twice.
• If you lose one of the transmitters, ask
your D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
as soon as possible for a replacement.
Be sure to have your dealer program
the new transmitter code in your
vehicle’s memory so that the old code is
erased. 3 D Q L F D O D U P I X Q F W L R Q L I H T X L S S H G
This function is to get the attention of oth-
ers.
Push both of the “LOCK” button (1) and
“UNLOCK” button (2) for more than 3 sec-
onds. The turn signal lights will blink for
about 27.5 seconds. Also, the siren will
sound for about 27.5 seconds at the same
time.
To cancel the panic alarm, press any but-
ton (LOCK or UNLOCK). You can also turn
the ignition switch to the “ON” position to
cancel the panic alarm.
NOTE:
The panic alarm function will not activate
when the key is in the ignition switch.
NOTICE
7 K H W U D Q V P L W W H U L V D V H Q V L W L Y H H O H F
W U R Q L F L Q V W U X P H Q W 7 R D Y R L G G D P D J L Q J
W K H W U D Q V P L W W H U
Page 35 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
outside, or using the door lock knobs or
the central door locking switch from
inside.
• If any door is not operated within approx-
imately 30 seconds after the doors have
been unlocked using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the doors are automatically
locked again. When the doors are
locked, the security system will be
armed in about 5 seconds if the system
is in the enabled state.
• If the security system indicator (1) blinks
when the ignition switch is in the “ON”
position or the ignition mode is “ON”,
there may be something wrong with the
security system. Ask your
D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S to
inspect the system.
+ R Z W R G L V D U P W K H V H F X U L W \ V \ V W H P
Simply unlock the doors using the keyless
entry system transmitter, keyless push
start system remote controller or request
switch. The security system indicator will
go out, indicating that the security system
is disarmed.
+ R Z W R V W R S W K H D O D U P
Should the alarm be triggered accidentally,
unlock the doors using the keyless entry
system transmitter, keyless push start sys-
tem remote controller or request switch, or
insert the key in the ignition switch and turn
it to “ON” position, or press the engineswitch to change the ignition mode to
“ON”. The alarm will then stop.
NOTE:
• Even after the alarm has stopped, if you
lock the doors using the keyless entry
system transmitter, keyless push start
system remote controller or request
switch, the security system will be
rearmed with a delay of about 5 sec-
onds.
• If you disconnect the battery while the
security system is in the armed condition
or the alarm is actually in operation, the
alarm will be re-triggered when the bat-
tery is then reconnected.
• Even after the alarm has stopped at the
end of the predetermined operation time,
it will be triggered again if any of the
doors or engine hood is opened, or the
vehicle feels a shock (if the shock sen-
sor is in the enabled state), without dis-
arming the security system.
& K H F N L Q J Z K H W K H U W K H D O D U P K D V E H H Q
W U L J J H U H G G X U L Q J S D U N L Q J
If the alarm was triggered and you then
turn the ignition switch to “ON” position, or
press the engine switch to change the igni-
tion mode to “ON”, the security system
indicator will blink rapidly for about 8 sec-
onds and a buzzer will beep 4 times during
this period. If this happens, check whether
the vehicle has been broken into while you
were away from it. ( Q D E O L Q J D Q G G L V D E O L Q J W K H V H F X U L W \
V \ V W H P
The security system can be either enabled
or disabled.
: K H Q H Q D E O H G
• If any of the doors are opened without
unlocking by the keyless entry system
transmitter, keyless push start system
remote controller or request switch, all
turn signal lights start to blink and the
interior buzzer beeps intermittently. After
5 seconds, the siren will sound for about
27.5 seconds. The security system indi-
cator continues to blink during this time.
• If the engine hood is opened, all turn sig-
nal lights blink, and the siren sounds for
about 27.5 seconds. The security sys-
tem indicator continues to blink during
this time.
( , I W K H V K R F N V H Q V R U L V L Q W K H H Q D E O H G
V W D W H
• If the vehicle feels a shock, the siren
sounds for about 2 seconds (pre-warn-
ing). If the vehicle continues to feel a
shock, all turn signal lights start to blink
and the interior buzzer beeps intermit-
tently. After 5 seconds, the siren will
sound for about 27.5 seconds (full blast
warning). The security system indicator
continues to blink during this time.
NOTE:
If you set the full blast warning sensitivity
higher than the pre-warning sensitivity in
the setting mode of the information display,
or the vehicle feels such shock as to be
Page 88 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
/ L J K W L Q J 2 S H U D W L R Q
60MK011
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions:
2 ) )
All lights are off.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
60MK012
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R P D W L F / L J K W V 2 S H U D W L R Q
L I H T X L S S H G
64MS059
64MS060
Your vehicle’s lighting system is controlled
by two main systems: the Lighting switch
and the Auto-On Headlight System (when
the lighting switch is in the “AUTO” posi-
tion).
The two systems work together to operate
your lights as shown in the following chart:
(3)
(2)
(1)
( ; $ 0 3 / (
( ; $ 0 3 / (
(3)(4)
(2) (1)
( ; $ 0 3 / (
(5)
Page 90 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
To turn the lights on or off, twist the knob
on the end of the lever. There are four
positions:
2 ) )
All lights are off.
$ 8 7 2
This function works when it on mode has
been changed to ON by pressing the
engine switch. The headlights and position
lights are turned on and off automatically
according to the amount of outside light
detected by a sensor. They go out auto-
matically when you change the ignition
mode to “ACC” or “LOCK” (OFF) by press-
ing the engine switch.
The light sensor (5) for sensing the amount
of outside light is installed on the upper
part of the windshield. It also serves as the
rain sensor for the rain-sensing wipers.NOTE:
• Avoid covering the light sensor area of
the windshield with a sticker. The sticker
may impair the performance of the sen-
sor and make the system unable to con-
trol operation of the lights correctly.
• If you changed the ignition mode to ON
by pressing the engine switch and the
“AUTO” position remains selected, the
headlights and position lights come on
automatically as the outside gets dark
even with the engine not running. Leav-
ing the lights lit for a long time may lead
to a completely discharged battery.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
64MS061
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R R Q K H D G O L J K W V \ V W H P
64MS062
The Auto-on headlight system automati-
cally turns on all lights that are operated by
the lighting control lever on the steering
column, when the following three condi-
tions are all met.
Conditions for Auto-on headlight system
operation:
1) It is dark around the light sensor (5).
2) The lighting control lever is in the
“AUTO” position.
3) You press the engine switch to change
the ignition mode to ON.
& $ 8 7 , 2 1
, I W K H O L J K W V H Q V R U D U H D R I W K H Z L Q G
V K L H O G L V F R Y H U H G Z L W K P X G L F H R U
R W K H U V L P L O D U V X E V W D Q F H V W K H K H D G
O L J K W V D Q G S R V L W L R Q O L J K W V P D \ E H
W X U Q H G R Q H Y H Q Z K H Q L W L V V W L O O O L J K W
R X W V L G H % H I R U H U H P R Y L Q J V X F K V X E
V W D Q F H V I U R P W K H Z L Q G V K L H O G D O Z D \ V
V H W W K H Z L S H U F R Q W U R O O H Y H U W R W K H
Page 91 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
This system is operated by a signal from the
light sensor (5) on the front windshield. Do
not cover the sensor (5). If you do, the sys-
tem will not work correctly.NOTE:
The light sensor is sensitive to infrared
rays, so it may operate incorrectly in the
region of strong infrared rays.
5 H S U R J U D P P L Q J W K H D X W R P D W L F O L J K W
I X Q F W L R Q
The following settings of the automatic
light function can be customized to your
preference. Please contact an D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S if you want the
function reprogrammed.
6 H Q V L W L Y L W \ R I W K H O L J K W V H Q V R U
The amount of outside light needed to turn
the lights on and off is pre-set at the fac-
tory. The sensitivity of the light sensor can
be adjusted so that the lights are turned on
and off when it is:
• lighter outside than the pre-set condition,
or
• darker outside than the pre-set condition 5 D L Q W U L J J H U H G D X W R P D W L F O L J K W L Q J R S H U
D W L R Q
The setting of the auto-on headlight sys-
tem can be changed to make it turn on the
headlights:
• when the rain sensor senses heavy rain-
fall
• when the rain sensor senses light and
heavy rainfall (in coordination with rain-
sensing wiper operation), or
• independently from rain-sensing wiper
operation. / L J K W 5 H P L Q G H U % X ] ] H UThe interior buzzer continuously beeps if
you open the driver’s door without turning
off the headlights and position lights. This
function is triggered under the following
condition:
The headlights and/or position lights are on
even after the ignition switch is turned off, or
the engine switch is pressed to change the
ignition mode to LOCK (OFF).
The buzzer stops sounding when you turn
off the headlights and position lights.NOTE:A message is indicated on the information
display in the instrument cluster while the
buzzer is sounding.
) U R Q W ) R J / L J K W 6 Z L W F K
L I H T X L S S H G
64J058
The front fog light comes on when the fog
light switch is pushed in with the position
lights, tail lights and/or the headlights are
on. An indicator light above the switch will
be lit when the front fog light is on.
NOTE:
In some countries the lighting operation
may be different from the above descrip-
tion according to local regulations.
: $ 5 1 , 1 *
, W W D N H V D E R X W V H F R Q G V I R U W K H O L J K W
V H Q V R U W R U H D F W W R D F K D Q J H L Q O L J K W L Q J
F R Q G L W L R Q V 7 R K H O S D Y R L G D Q D F F L G H Q W
G X H W R U H G X F H G Y L V L E L O L W \ W X U Q R Q \ R X U
K H D G O L J K W V E H I R U H G U L Y L Q J L Q W R D W X Q Q H O
S D U N L Q J V W U X F W X U H R U W K H O L N H
Page 92 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
+ H D G O L J K W / H Y H O L Q J 6 Z L W F K
80JM040
Level the headlight beam according to the
load condition of your vehicle by turning this
switch. The chart below shows the appropri-
ate switch position for different vehicle-load
conditions.
7 X U Q 6 L J Q D O & R Q W U R O / H Y H U
65D611
7 X U Q 6 L J Q D O 2 S H U D W L R QWith the ignition switch in the “ON” position
or the ignition mode ON, move the lever up
or down to activate the right or left turn sig-
nals.
1 R U P D O W X U Q V L J Q D O
60MK013
Move the lever all the way upward or
downward to signal. When the turn is com-
pleted, the signal will cancel and the lever
will return to its normal position.
/ D Q H F K D Q J H V L J Q D O
60MK014
Move the lever part-way in the direction to
turn and hold it there.
Vehicle Load
Condition
Switch PositionD13A
EngineD16AA
Engine
Driver only 0 0Driver +
1 passenger
(in front seat)
00
Driver +
4 passengers,
no cargo
11
Driver +
4 passengers,
cargo added
22
Driver +
full cargo
33
: $ 5 1 , 1 *
7 R D Y R L G S R V V L E O H L Q M X U \ G R Q R W R S H U
D W H F R Q W U R O V E \ U H D F K L Q J W K U R X J K W K H
V W H H U L Q J Z K H H O
( ; $ 0 3 / ( ( ; $ 0 3 / (
Page 93 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
• The turn signal and its indicator flash
while the lever is held at the moved posi-
tion.
The turn signal and its indicator flash three
times even if you return the lever immedi-
ately after moving it.
NOTE:
The turn signal and its indicator can be set
whether they flash three times after the
turn signal lever is returned via the infor-
mation display. Refer to “Information Dis-
play” in this section.
NOTE:
You can customize the setting for the num-
ber of times of flashing of the turn signal
and its indicator (1 to 4 times). Please ask
an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S for
the customization.
+ D ] D U G : D U Q L Q J 6 Z L W F K
61M0163
Push in the hazard warning switch to acti-
vate the hazard warning lights. All turn sig-
nal lights and both turn signal indicators
will flash simultaneously. To turn off the
lights, push the switch again.
Use the hazard warning lights to warn
other traffic during emergency parking or
when your vehicle could otherwise become
a traffic hazard.
: L Q G V K L H O G : L S H U D Q G : D V K H U
/ H Y H U
57L21128
( ; $ 0 3 / (
: $ 5 1 , 1 *
7 R D Y R L G S R V V L E O H L Q M X U \ G R Q R W R S H U
D W H F R Q W U R O V E \ U H D F K L Q J W K U R X J K W K H
V W H H U L Q J Z K H H O