brake TOYOTA AVENSIS 1999 Supplement

INTRODUCTION
PREPARATION
SERVICE SPECIFICATIONS
DIAGNOSTICS
E251 MANUAL TRANSAXLE
SUSPENSION AND AXLE
BRAKE
STEERING
SUPPLEMENTAL RESTRAINT SYSTEM
BODY ELECTRICAL
BODY
AIR CONDITIONING
ALPHABETICAL INDEX

Illustration:
what to do and where
21. CHECK PISTON STROKE OF OVERDRIVE BRAKE
(a)
Task heading : what to do
SST 09350–30020 (09350–06120)
Set part No. Component part No.
Detailed text : how to do task
(b)
Piston stroke: 1.40
1.70 mm (0.0551
 
Specification
Place SST and a dial indicator onto the overdrive brake pis-
ton as shown in the illustration.
Measure the stroke applying and releasing the compressed
air (392
 
kgf/cm
2 or 57
114 psi) as shown
in the illustration. IN–2
– INTRODUCTIONHOW TO USE THIS MANUAL
The procedures are presented in a step–by–step format:
The illustration shows what to do and where to do it.
The task heading tells what to do.
The detailed text tells how to perform the task and gives other information such as specifications
and warnings.
Example

This format provides the experienced technician with a FAST TRACK to the information needed. The upper
case task heading can be read at a glance when necessary, and the text below it provides detailed informa-
tion. Important specifications and warnings always stand out in bold type.
6. REFERENCES
References have been kept to a minimum. However, when they are required you are given the page to refer
to.
7. SPECIFICATIONS
Specifications are presented in bold type throughout the text where needed. You never have to leave the
procedure to look up your specifications. They are also found in Service Specifications section for quick ref-
erence.
8. CAUTIONS, NOTICES, HINTS:
CAUTIONS are presented in bold type, and indicate there is a possibility of injury to you or other
people.
NOTICES are also presented in bold type, and indicate the possibility of damage to the components
being repaired.
HINTS are separated from the text but do not appear in bold. They provide additional information to
help you perform the repair efficiently.
9. SI UNIT
The UNITS given in this manual are primarily expressed according to the SI UNIT (International System of
Unit), and alternately expressed in the metric system and in the English System.
Example:
Torque: 30 N·m (310 kgf·cm, 22 ft·lbf)

B07465
New
Previous
– INTRODUCTIONFOR ALL OF VEHICLES
IN–17
5. FOR VEHICLES EQUIPPED WITH POWER WINDOW CONTROL SYSTEM
When the battery is disconnected or the power to the window regulator motor is cut, the power window con-
trol system does not operate. It is necessary to initialize the system in the following procedures. Otherwise
window cannot be operated normally.
(1) Close window to the highest position.
(2) Keep holding the switch for 5 seconds.
(3) Check that automatic operation works. If not, repeat the above procedures.
6. FOR VEHICLES EQUIPPED WITH SLIDING ROOF SYSTEM
Sliding roof stop position might be required to be initialized when battery failures (such as battery disconnec-
tion, connector disconnection and the voltage drop) are detected while the system is in operation. This also
occurs when rotating the motor with the battery disconnected. Sliding roof initialization can be done by the
following procedures.
(1) Operate the roof up to the maximum tilt position.
(2) Release the switch, and push it again in the same direction. (After 10 seconds have elapsed,
initialization begins.)
(3) The roof starts automatic operation if holding the switch, completes full one cycle (tilt down, slide
open, slide close and tilt up) of travel. Do not release the switch until the roof stops.
(4) Check that the roof stops at the correct position.
7. FOR VEHICLES EQUIPPED WITH BRAKE PIPE FIT-
TING OF NEW STANDARD
A flare shape of a new standard is used for the brake pipe fitting
from this changed models.
NOTICE:
When ordering or replacing the parts, please be sure
to check and use the fitting of the same flare type.
Do not over–tighten them more than the standard
torque.
Torque: 15 N·m (155 kgf·cm, 11 ft·lbf)

IN044–07
IN–34
– INTRODUCTIONTERMS
TERMS
ABBREVIATIONS USED IN THIS MANUAL
AbbreviationsMeaning
ABSAnti–Lock Brake System
A/CAir Conditioner
ACAlternating Current
ACCAccessory
ACISAcoustic Control Induction System
ACSDAutomatic Cold Start Device
A.D.D.Automatic Disconnecting Differential
AHCActive Height Control Suspension
ALRAutomatic Locking Retractor
ALTAlternator
AMPAmplifier
ANTAntenna
APPROX.Approximately
A/TAutomatic Transmission (Transaxle)
AT FAutomatic Transmission Fluid
AUTOAutomatic
BACSBoost Altitude Compensation System
BATBattery
B/LBi–Level
BVSVBimetallic Vacuum Switching Valve
CBCircuit Breaker
CDCompact Disc
CHChannel
CKDComplete Knock Down
COMB.Combination
CPECoupe
CRSChild Restraint System
CTRCenter
DCDirect Current
DIFF.Differential
DIFF. LOCKDifferential Lock
DLCData Link Connector
DSPDigital Signal Processor
DTCDiagnostic Trouble Code
ECTElectronic Control Transmission
ECUElectronic Control Unit
EDUElectronic Driving Unit
EFIElectronic Fuel Injection
E/GEngine
EGRExhaust Gas Recirculation
ELREmergency Locking Retractor
E–VRVElectronic Vacuum Regulating Valve

IN–36
– INTRODUCTIONTERMS
PKB
Parking Brake
PPSProgressive Power Steering
PSPower Steering
PTOPower Take–Off
RAMRandom Access Memory
R/BRelay Block
RBSRecirculating Ball Type Steering
R/FReinforcement
RFSRigid Front Suspension
RHRight–Hand
RHDRight–Hand Drive
RLYRelay
ROMRead Only Memory
RrRear
RRRear–Engine Rear–Wheel Drive
RRSRigid Rear Suspension
RWDRear–Wheel Drive
SDNSedan
SENSensor
SICSStarting Injection Control System
SPECSpecification
SRSSupplemental Restraint System
SSMSpecial Service Materials
SSTSpecial Service Tools
STDStandard
SWSwitch
SYSSystem
T/ATransaxle
TACHTachometer
TDCTop Dead Center
TEMP.Temperature
TEMSTOYOTA Electronic Modulated Suspension
TFTToyota Free–Tronic
T/MTransmission
TMCTOYOTA Motor Corporation
TRCTraction Control System
U/DUnderdrive
VENTVentilator
VINVehicle Identification Number
VSCVehicle Skid Control Vehicle Stability Control
VSVVacuum Switching Valve
w/With
WGNWagon
W/HWire Harness
w/oWithout
1stFirst

PREPARATION
MANUAL TRANSAXLE (E251) PP–1. . . . . . . . . . . . .
SUSPENSION AND AXLE PP–6. . . . . . . . . . . . . . . .
BRAKE PP–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING PP–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUPPLEMENTAL RESTRAINT SYSTEM PP–16. . .
BODY ELECTRICAL PP–19. . . . . . . . . . . . . . . . . . . . .
BODY PP–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR CONDITIONING PP–22. . . . . . . . . . . . . . . . . . . . .
REFER TO AVENSIS/CORONA REPAIR MANUAL FOR
CHASSIS AND BODY (Pub. No. RM599E)
NOTE: The above pages contain only the points which differ
from the above listed manual.

PP27W–01
– PREPARATIONBRAKE
PP–11
BRAKE
EQUIPMENT
Torque wrench
MicrometerBlade

PP12J–02
– PREPARATIONBODY ELECTRICAL
PP–19
BODY ELECTRICAL
EQUIPMENT
Voltmeter
Ammeter
Ohmmeter
Test lead
SyphonBrake fluid level warning switch
Bulb (3.4 W)Fuel sender gauge,
Dry cell batteryFuel sender gauge

SERVICE SPECIFICATIONS
STANDARD BOLT SS–1. . . . . . . . . . . . . . . . . . . . . . . .
MANUAL TRANSAXLE (E251) SS–4. . . . . . . . . . . . .
SUSPENSION AND AXLE SS–9. . . . . . . . . . . . . . . .
BRAKE SS–11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STEERING SS–13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUPPLEMENTAL RESTRAINT SYSTEM SS–15. . .
BODY ELECTRICAL SS–16. . . . . . . . . . . . . . . . . . . . .
BODY SS–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR CONDITIONING SS–19. . . . . . . . . . . . . . . . . . . . .
REFER TO AVENSIS/CORONA REPAIR MANUAL FOR
CHASSIS AND BODY (Pub. No. RM599E)
NOTE: The above pages contain only the points which differ
from the above listed manual.

SS14B–01
– SERVICE SPECIFICATIONSBRAKE
SS–11
BRAKE
SERVICE DATA
Vacuum Pump
(1CD–FTV)Blade Minimum height
Minimum width
Minimum length16.20 mm (0.6378 in.)
5.95 mm (0.2343 in.)
44.96 mm (1.7701 in.)