check oil TOYOTA AYGO 2011 Owners Manual
[x] Cancel search | Manufacturer: TOYOTA, Model Year: 2011, Model line: AYGO, Model: TOYOTA AYGO 2011Pages: 318, PDF Size: 13.73 MB
Page 32 of 318
22KEYS AND DOORS
MS12020a
3. Remove the discharged battery.
MS12021b
4. Put in a new battery with positive (+)
side up.
Close the cover securely.
NOTICE
zMake sure the positive side and
negative side of the battery are
faced correctly.
zDo not replace the battery with wet
hands. Water may cause unexpected
rust.
zDo not touch or move any compo-
nents inside the transmitter, or it
may interfere with proper operation.
zBe careful not to bend the electrode
when inserting the battery and that
dust or oils do not adhere to the
cover.
zTake care not to lose the screw.
zClose the cover securely.
After replacing the battery, check that the
key operates properly. If the key still does
not operate properly, contact any autho-
rized Toyota dealer or repairer, or another
duly qualified and equipped professional.
AYGO WE 99E37E11 02.18
Page 140 of 318
130GAUGES, METERS AND SERVICE REMINDER INDICATORS
(c) Front Passenger ’s Seat Belt
Reminder Light and Buzzer
The light and buzzer act as a reminder to
have the front passenger buckle up the
seat belt.
Once the engine switch is turned to “ON”
or “START”, the reminder light flashes if
a passenger sits in the front passenger
seat and does not fasten the seat belt.
Unless the front passenger fastens the
belt, the light continues flashing.
If the vehicle speed rises above 20 km/h
(12 mph) with the seat belt unfastened,
the buzzer will sound for 30 seconds.
Then, if the seat belt is still unfastened,
the buzzer will sound in a different tone
for 90 more seconds. Even if the vehicle
speed drops below 20 km/h (12 mph), the
buzzer will continue to sound. To stop the
buzzer, fasten the seat belt. If the buzzer
still sounds, make sure the driver ’s seat
belt is fastened.
If luggage or other load is placed on the
front passenger seat, depending on its
weight and how it is placed on the seat,
built−in sensors in the seat cushion may
detect the pressure, causing the reminder
light to flash and buzzer to sound.
(d) Charging System Warning Light
This warning light comes on when the
engine switch is turned to the “ON” posi-
tion, and goes off when the engine is
started.
When there are problems in the charging
system while theengine is running, the
warning light comes on.
NOTICE
When the charging system warning
light comes on while the engine is
running, malfunctions such as the en-
gine drive belt being broken may have
occurred. If the warning light comes
on, immediately stop the vehicle in a
safe place and contact any authorized
Toyota dealer or repairer, or another
duly qualified and equipped profes-
sional.
(e) Low Engine Oil Pressure Warning
Light
This light warns that the engine oil pres-
sure is too low.
If the engine oil pressure warning light
comes on, pull off the road to a safe
place and stop the engine immediately.
Call any authorized Toyota dealer or re-
pairer, or another duly qualified and
equipped professional, for assistance. The
“STOP” warning light also comes on at
thesametime.
The light may occasionally flicker when
the engine is idling or it may come on
briefly after a hard stop. There is no
cause for concern if it then goes out when
the engine is accelerated slightly.
The light may come on when the engine
oil level is extremely low. It is not de-
signed to indicate low engine oil level, and
the engine oil level must be checked us-
ing the level dipstick.
NOTICE
Do not drive the vehicle with the
warning light on—even for one block.
It may ruin the engine.
AYGO WE 99E37E11 02.18
Page 141 of 318
GAUGES, METERS AND SERVICE REMINDER INDICATORS131
(f) Malfunction Indicator Lamp
This lamp warns that there is a problem
somewhere in your engine electrical sys-
tem.
If it comes on while you are driving, have
your vehicle checked/repaired by any au-
thorized Toyota dealer or repairer, or
another duly qualified and equipped pro-
fessional, as soon as possible.
On some models—
This lamp comes on in the following
cases.
a. There is a problem somewhere in your
engine, automatic transmission electri-
cal system or electronic throttle control
system.
b. The fuel tank is completely empty.
(See “Fuel gauge” on page 124 in this
Section for instructions.)
If it comes on while you are driving in
case a, have your vehicle checked/re-
paired by any authorized Toyota dealer or
repairer, or another duly qualified and
equipped professional, as soon as pos-
sible.
Vehicles with multi−mode manual transmis-
sion or vehicle stability control system—
If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.
At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your Toyota
checked by any authorized Toyota dealer
or repairer, or another duly qualified and
equipped professional, as soon as pos-
sible.
Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, thesystem may not be
recovered until the engine is stopped and
the engine switch is turned to “ACC” or
“LOCK” position.CAUTION
Be especially careful to prevent erro-
neous pedal operation.
(g) “STOP” Warning Light
This light will come on when the engine
switch is turned to the “ON” position. After
a few seconds, the light will blink. When
the engine is started, the light will go off.
This means thesystem of the “STOP”
warning operating properly.
This light blinks in the following cases:
DWhen the engine coolant temperature
becomes high and the engine coolant
temperature warning light blinks. If the
engine coolant temperature rises fur-
ther, the engine coolant temperature
warning light remains on and at the
same time, the “STOP” warning light
blinks. In such cases, the engine is too
hot. If your vehicle overheats, stop the
vehicle and allow the engine to cool
down.
DWhen the engine oil pressure is too
low, the low engine oil pressure warn-
ing light comes on and at the same
time, the “STOP” warning light blinks.
In this case, pull off the road to a safe
place and stop the engine immediately.
Call any authorized Toyota dealer or re-
pairer, or another duly qualified and
equipped professional, for assistance.
(h) Low Fuel Level Warning Light and
Buzzer
The warning light blinks and the warning
buzzer comes on when the fuel level in
the tank becomes nearly empty. Fill up
the tank as soon as possible.
On incline or curves, due to the move-
ment of fuel in the fuel tank, the warning
light may blinks and the warning buzzer
may come on earlier than usual.
AYGO WE 99E37E11 02.18
Page 209 of 318
INFORMATION BEFORE DRIVING YOUR TOYOTA199
FUNCTIONS OF ENGINE OIL
Engine oil has the primary functions of
lubricating and cooling the inside of the
engine, and plays a major role in main-
taining the engine in proper working order.
ENGINE OIL CONSUMPTION
It is normal that an engine should con-
sume some engine oil during normal
engine operation. The causes of oil
consumption in a normal engine are as
follows.
DOil is used to lubricate pistons, piston
rings and cylinders. A thin film of oil
is left on the cylinder wall when a pis-
ton moves downwards in the cylinder.
High negative pressure generated when
the vehicle is decelerating sucks some
of this oil into the combustion chamber.
This oil as well as some part of the oil
film left on the cylinder wall is burned
by the high temperature combustion
gases during the combustion process.
DOil is also used to lubricate the stems
of the intake valves. Some of this oil
is sucked into the combustion chamber
together with the intake air and is
burned along with the fuel. High tem-
perature exhaust gases also burn the
oil used to lubricate the exhaust valve
stems.
The amount of engine oil consumed de-
pends on the viscosity of the oil, the
quality of the oil and the conditions the
vehicle is driven under.
More oil is consumed by high−speed driv-
ing and frequent acceleration and decel-
eration.
A new engine consumes more oil, since
its pistons, piston rings and cylinder walls
have not become conditioned.Oil consumption:Max. 1.0 L per 1000
km (1.1 qts./600 miles, 0.9 lmp.qts./600
miles)
When judging the amount of oil con-
sumption, note that the oil may become
diluted and make it difficult to judge
the true level accurately.
As an example, if a vehicle is used for
repeated short trips, and consumes a nor-
mal amount of oil, the dipstick may not
show any drop in the oil level at all, even
after 1000 km (600 miles) or more. This
is because the oil is gradually becoming
diluted with fuel or moisture, making it
appear that the oil level has not changed.
The diluting ingredients evaporate out
when the vehicle is then driven at high
speeds, as on an expressway, making it
appear that oil has been excessively con-
sumed while driving at high speeds.
IMPORTANCE OF ENGINE OIL LEVEL
CHECK
One of the most important points in prop-
er vehicle maintenance is to keep the en-
gine oil at the optimum level so that oil
function will not be impaired. Therefore, it
is essential that the oil level be checked
regularly. Toyota recommends that the oil
level be checked every time you refuel
the vehicle.
NOTICE
Failure to check the oil level regularly
could lead to serious engine trouble
due to insufficient oil.
For detailed information on oil level check,
see “Checking the engine oil level” on
page 264 in Section 7−2.
AYGO WE 99E37E11 02.18
Facts about engine oil
consumption
Page 221 of 318
STARTING AND DRIVING211
Before starting the engine, be sure to
follow the instructions in “(a) Before
cranking”.
Normal starting procedure
The multiport fuel injection system/sequen-
tial multiport fuel injection system in your
engine automatically controls the proper
air−fuel mixture for starting. You can start
a cold or hot engine as follows:
Multi−mode manual transmission:With
your foot off the accelerator pedal, turn
the engine switch to the “START” posi-
tion and crank the engine while depress-
ing the brake pedal. Release the key
when the engine starts. The engine can-
not be cranked if the shift lever is in a
position except “N” or the brake pedal
is not depressed.
Manual transmission:With your foot off
the accelerator pedal, crank the engine
by turning the engine switch to the
“START” position. Release it when the
engine starts.
Engine should be warmed up by driving,
not idling. For warming up drive with a
smoothly turning engine until the engine
coolant temperature is within the normal
range.
If the engine stalls...
Simply restart it, using the correct proce-
dure given in normal starting.
If the engine will not start...
See “If your vehicle will not start” on page
220 in Section 4.
NOTICE
zDo not crank for more than 30 se-
conds at a time. This may overheat
the starter and wiring systems.
zDo not race a cold engine.
zIf the engine becomes difficult to
start or stalls frequently, have the
engine checked immediately.
Pre−trip safety check
It is a good idea to do a safety check
before starting out on a trip. A few min-
utes of checking can help ensure safe and
pleasant driving. Just a basic familiarity
with your vehicle is required and a careful
eye! Or, if you would like, any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional, will
be pleased to make this check for you at
nominal cost.
CAUTION
If you make this check in an enclosed
garage, make sure there is adequate
ventilation. Engine exhaust is poison-
ous.
BEFORE STARTING THE ENGINE
Outside the vehicle
Tires.Check the pressure with a gauge
and look carefully for cuts, damage, or
excessive wear.
Wheel bolts.Make sure no bolts are mis-
sing or loose.
Fluid leaks.After the vehicle has been
parked for a while, check underneath for
leaking fuel, oil, water, or fluid. (Water
dripping from the air conditioning after use
is normal.)
Lights.Make sure the headlights, stop
lights, tail lights, turn signals and other
lights are all working. Check the headlight
aim.
Inside the vehicle
Spare tire, jack and wheel bolt wrench.
Check the spare tire pressure and make
sure you have your jack and wheel bolt
wrench.
AYGO WE 99E37E11 02.18
(b) Starting the engine
Page 222 of 318
212STARTING AND DRIVING
Seat belts.Check that the buckles lock
securely. Make sure the belts are not
worn or frayed.
Instruments and controls.Especially
make sure the service reminder indicators,
instrument lights, and defroster are work-
ing.
Brakes.Make sure the pedal has enough
clearance.
In the engine compartment
Spare fuses.Make sure you have spare
fuses. (See “Fuse locations” on page 259
in Section 7−1.)
Coolant level.Make sure the coolant lev-
el is correct. (See page 267 in Section
7−2 for instructions.)
Battery and cables.All the battery cells
should be filled to the proper level with
distilled water. Look for corroded or loose
terminals and a cracked case. Check the
cables for good condition and connections.
Wiring.Look for damaged, loose, or dis-
connected wires.
Fuel lines.Check the lines for leaks or
loose connections.
AFTER STARTING THE ENGINE
Exhaust system.Listen for any leakage.
Have any leaks fixed immediately. (See
“Engine exhaust cautions” on page 198 in
Section 2.)
Engine oil level.Stop the engine and
check the dipstick with the vehicle parked
on a level spot. (See page 264 in Section
7−2 for instructions.)
WHILE DRIVING
Instruments.Make sure the speedometer
and gauges are working.
Brakes.In a safe place, check that the
brakes do not pull to one side when ap-
plied.Anything unusual?Look for loose parts
and leaks. Listen for abnormal noises.
If everything looks O.K., set your mind at
ease and enjoy your trip!
AYGO WE 99E37E11 02.18
Page 224 of 318
214STARTING AND DRIVING
Driving in the rain
Driving on a slippery road surface
Drive carefully when it is raining, because
visibility will be reduced, the windows may
become fogged−up, and the road will be
slippery.
DDrive carefully when it starts to rain,
because the road surface will be espe-
cially slippery.
DRefrain from high speeds when driving
on an expressway in the rain, because
there may be a layer of water between
the tires and the road surface, prevent-
ing the steering and brakes from oper-
ating properly.
CAUTION
DSudden braking, acceleration and
steering when driving on a slippery
road surface may cause tire slip-
page and reduce your ability to
control the vehicle, resulting in an
accident.
DSudden changes in engine speed,
such as sudden engine braking,
may cause the vehicle to skid, re-
sulting in an accident.
DAfter driving through a puddle,
lightly depress the brake pedal to
make sure that the brakes are func-
tioning properly. Wet brake pads
may prevent the brakes from func-
tioning properly. If the brakes on
only one side are wet and not func-
tioning properly, steering control
may be affected, resulting in an ac-
cident.
When encountering flooded roads
Do not drive on a road that has flooded
after heavy rain etc. Doing so may cause
serious damage to the vehicle.
NOTICE
Driving on a flooded road may cause
the engine to stall as well as cause
serious vehicle malfunctions such as
shorts in electrical components and
engine damage from water immersion.
In the event that you drive on a
flooded road and the vehicle is
flooded, be sure to have your Toyota
dealer check brake function, changes
in quantity and quality of engine oil,
transaxle fluid, etc. and lubricant con-
dition for the bearings and suspen-
sion joints (where possible) and the
function of all joints and bearings.
AYGO WE 99E37E11 02.18
Page 225 of 318
STARTING AND DRIVING215
Winter driving tips
Make sure your coolant is properly pro-
tected against freezing.
Only use “Toyota Super Long Life Coolant”
or similar high quality ethylene glycol
based non−silicate, non−amine, non−nitrite,
and non−borate coolant with long−life hy-
brid organic acid technology. (Coolant with
long−life hybrid organic acid technology is
a combination of low phosphates and or-
ganic acids.)
See “Checking the engine coolant level”
on page 267 in Section 7−2 for details of
coolant type selection.
“Toyota Super Long Life Coolant” is a mix-
ture of 50% coolant and 50% deionized
water. This coolant provides protection
down to about−35_C(−31_F).
NOTICE
Do not use plain water alone.
Check the condition of the battery and
cables.
Cold temperatures reduce the capacity of
any battery, so it must be in top shape
to provide enough power for winter start-
ing. Section 7−3 tells you how to visually
inspect the battery. Any authorized Toyota
dealer or repairer, or another duly quali-
fied and equipped professional, will be
pleased to check the level of charge.
Make sure the engine oil viscosity is
suitable for the cold weather.
See page 264 in Section 7−2forrecom-
mended viscosity. Leaving a heavy sum-
mer oil in your vehicle during winter
months may make starting harder. If you
are not sure about which oil to use, call
any authorized Toyota dealer or repairer,
or another duly qualified and equipped
professional, they will be pleased to help.
Keep the door locks from freezing.
Squirt lock de−icer or glycerine into the
locks to keep them from freezing.Use a washer fluid containing an anti-
freeze solution.
This product is available at any authorized
Toyota dealer or repairer and most auto
parts stores or another qualified profes-
sional. Follow the manufacturer ’s direc-
tions for how much to mix with water.
NOTICE
Do not use engine antifreeze or any
other substitute because it may dam-
age your vehicle’s paint.
Do not use your parking brake when
there is a possibility it could freeze.
When parking, put the transmission into
“M(1)”, “E(1)” or “R” (multi−mode manual
transmission), or into first or reverse
(manual transmission) and block the rear
wheels. Do not use the parking brake,
snow or water accumulated in and around
the parking brake mechanism may freeze,
making it hard to release.
Keep ice and snow from accumulating
under the fenders.
Ice and snow built up under your fenders
can make steering difficult. During bad
winter driving, stop and check under the
fenders occasionally.
Depending on where you are driving,
we recommend you carry some emer-
gency equipment.
Some of the things you might put in the
vehicle are tire chains, a window scraper,
a bag of sand or salt, flares, a small
shovel, jumper cables, etc.
AYGO WE 99E37E11 02.18
Page 235 of 318
IN CASE OF AN EMERGENCY225
If engine speed does not increase when
the accelerator pedal is depressed, there
may be a problem somewhere in the elec-
tronic throttle control system.
At this time, vibration may occur. Howev-
er, if you depress the accelerator pedal
more firmly and slowly, you can drive your
vehicle at low speeds. Have your Toyota
checked by any authorized Toyota dealer
or repairer, or another duly qualified and
equipped professional, as soon as pos-
sible.
Even if the abnormality of the electronic
throttle control system is corrected during
low speed driving, thesystem may not be
recovered until the engine is stopped and
the engine switch is turned to “ACC” or
“LOCK” position.
CAUTION
Be especially careful to prevent erro-
neous pedal operation.
If your high engine coolant temperature
warning light flashes to indicates over-
heating, if you experience a loss of
power, or if you hear a loud knocking
or pinging noise, the engine has prob-
ably overheated. You should follow this
procedure...
1. Pull safely off the road, stop the ve-
hicle and turn on your emergency
flashers. Put the transmission in “N”
(multi−mode manual transmission), or
neutral (manual transmission) and ap-
ply the parking brake. Turn off the air
conditioning if it is being used.
2. If coolant or steam is boiling out of the
radiator or reservoir, stop the engine.
Wait until the steam subsides before
opening the hood. If there is no coolant
boiling over or steam, leave the engine
running and make sure the electric
cooling fan is operating. If it is not,
turn the engine switch off.
CAUTION
To help avoid personal injury, keep
the hood closed until there is no
steam. Escaping steam or coolant is
a sign of very high pressure.
3. Look for obvious coolant leaks from the
radiator, hoses, and under the vehicle.
However, note that water draining from
the air conditioning is normal if it has
been used.
CAUTION
When the engine is running, keep
hands and clothing away from the
moving fan and engine drive belts.
AYGO WE 99E37E11 02.18
If you cannot increase engine
speed (vehicles with multi−mode
manual transmission or vehicle
stability control system)
If your vehicle overheats
Page 273 of 318
DO−IT−YOURSELF MAINTENANCE: Engine and Chassis263
Section 7−2
DO−IT−YOURSELF MAINTENANCE
Engine and Chassis
DChecking the engine oil level 264........................
DChecking the engine coolant level 267...................
DChecking the radiator and condenser 268................
DChecking the clutch pedal free play 269..................
DChecking tire inflation pressure 269.....................
DChecking and replacing tires 270........................
DRotating tires 272......................................
DInstalling snow tires and chains 273.....................
DReplacing wheels 275..................................
DAluminum wheel precautions 275.......................
AYGO WE 99E37E1102.18