brake pads YAMAHA BLASTER 200 2006 Manuale de Empleo (in Spanish)
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2006, Model line: BLASTER 200, Model: YAMAHA BLASTER 200 2006Pages: 388, tamaño PDF: 7.56 MB
Page 108 of 388
5-7
Brake fluid leakage
Check to see if any brake fluid is leaking out of
the pipe joints or brake fluid reservoirs. Apply
the brakes firmly for one minute. If there is any
leakage, have a Yamaha dealer inspect the
brake system.
Brake operation
Test the brakes at slow speed after starting out
to make sure they are working properly. If the
brakes do not provide proper braking perfor-
mance, inspect the brake pads for wear. (See
page 8-59.)
w
Always check the brakes at the start of every
ride. Do not ride the ATV if you find any prob-
lem with the brakes or you could lose braking
ability, which could lead to an accident. If a
problem cannot be corrected by the adjust-
ment procedures provided in this manual,
have a Yamaha dealer check for the cause.
5VM-9-63-02 3/29/05 4:01 PM Page 44
Page 257 of 388
8-8INITIAL EVERY
month 1 3 6 6 12
ITEM ROUTINEWhichever
km 320 1200 2400 2400 4800 comes first
(mi) (200) (750) (1500) (1500) (3000)
hours 20 75 150 150 300
* Front and rear9Check pad wear.
222
brake pads9Replace if necessary.
* Clutch9Inspect free play and operation.
2222
9Replace if necessary.
Drive chain9Lubricate, check free play and alignment.
2222
9Replace if necessary.
* Drive chain guard
9Check wear and replace if necessary.222
and rollers
* Steering system9Inspect play, clean and lubricate with lithium-soap-
22222
based grease.
* Front and rear9Inspect and lubricate with lithium-soap-based
22222
suspensiongrease.
Tires9Inspect air pressure, wheel runout, and tire wear.22222
* Wheels9Inspect bearings.
22222
9Replace bearings if necessary.
* Throttle, control 9Check routing and connection.
22222
cables9Lubricate.
Outside nuts and bolts9Tighten if necessary.22222
Frame9Clean and inspect.2222
Lighting9Inspect.22222
5VM-9-63-05 3/29/05 4:03 PM Page 9
Page 304 of 388
LOWERq
LOWER1
1. Minimum level mark 1. Repère de niveau minimum 1. Marca del nivel mínimo 1. Minimum level mark
1. Repère de niveau minimum 1. Marca del nivel mínimo Front
AvantDelantero
RearArrièreTrasero
Recommended brake fluid: DOT 4
EBU13040
Brake fluid level check
Insufficient brake fluid may let air enter the
brake system, possibly causing the brakes to
become ineffective.
Before riding, check that the brake fluid is above
the minimum level mark and replenish if neces-
sary. A low brake fluid level may indicate worn
brake pads and/or brake system leakage. If the
brake fluid level is low, be sure to check the
brake pads for wear and the brake system for
leakage.
Observe these precautions:
8When checking the brake fluid level, make
sure the top of the brake fluid reservoir is
level.
8Use only the designated quality brake fluid,
otherwise, the rubber seals may deteriorate,
causing leakage and poor brake perfor-
mance.
8-55
5VM-9-63-05 3/29/05 4:04 PM Page 56
Page 308 of 388
8-59
EBU13770
Front brake pad check
Check the brake pads for damage and wear. If a
brake pad thickness is less than 1 mm, have a
Yamaha dealer replace the pads as a set.
NOTE:
The wheels need to be removed to check the
brake pads. (See pages 8-87 for removal and
installation procedures.)
EBU00314
Rear brake pad inspection
A wear indicator is provided on each brake pad.
This indicator allows checking of brake pad wear
without disassembling the brake. Apply the
brake and inspect the wear indicator. If the
brake pads are worn to the wear limit, have a
Yamaha dealer replace the pads.
a
1
1
a. Wear limita. Limite d’usurea. Límite de desgaste
1. Wear indicator
1. Indicateur d’usure1. Inidcador de desgasteFront
AvantDelantero
RearArrièreTrasero
5VM-9-63-05 3/29/05 4:04 PM Page 60