fuel cap YAMAHA FX HO 2007 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2007, Model line: FX HO, Model: YAMAHA FX HO 2007Pages: 108, PDF Size: 7.59 MB
Page 6 of 108
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 8
Safety information ........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 12
Recommended equipment ........... 14
Hazard information ....................... 15
Watercraft characteristics ............. 15
Water-skiing ................................. 17
Safe boating rules ........................ 19
Enjoy your watercraft
responsibly ................................ 19
Features and functions ................... 20
Location of main components ...... 20
Operation of controls and
other functions ........................... 24
Seats ............................................... 24
Hood ................................................ 25
Fuel tank filler cap ........................... 26
Remote control transmitter .............. 26
Engine stop switch .......................... 27
Engine shut-off switch ..................... 27
Start switch ...................................... 27
Throttle lever ................................... 28
Cooling water pilot outlets ............... 28
Steering system ............................... 28
Tilt lever ........................................... 29
Shift lever ......................................... 29
Quick Shift Trim System (QSTS)
selector ........................................ 30Handgrip .......................................... 32
Reboarding step ............................... 32
Bow eye ........................................... 32
Stern eyes ....................................... 33
Pull-up cleats
(for FX Cruiser High Output) ........ 33
Yamaha Engine Management
System (YEMS) ........................... 33
Yamaha Security System ................ 33
Multifunction information center ...... 34
Storage compartments .................... 45
Operation ......................................... 49
Fuel and oil .................................. 49
Gasoline .......................................... 49
Engine oil ......................................... 50
Filling the fuel tank .......................... 50
Pre-operation checks ................... 51
Pre-operation check list ................... 51
Pre-operation check points .............. 53
Operation ..................................... 61
Engine break-in ............................... 61
Launching the watercraft ................. 61
Starting the engine .......................... 61
Stopping the engine ........................ 63
Leaving the watercraft ..................... 63
Operating your watercraft ............ 64
Getting to know your watercraft ....... 64
Learning to operate your
watercraft ..................................... 64
Riding with passengers ................... 65
Starting the watercraft ..................... 65
Boarding and starting in
deep water ................................... 66
Capsized watercraft ......................... 69
Turning the watercraft ..................... 70
Stopping the watercraft ................... 72
Beaching the watercraft ................... 72
Docking the watercraft ..................... 72
Reverse on waterways ..................... 72
Rough water operation .................... 73
UF1X71E0.book Page 1 Tuesday, September 26, 2006 9:52 AM
Page 28 of 108
Features and functions
21
Rear view
1Fuel tank filler cap
2Intake grate
3Speed sensor
4Stern eyes
5Stern drain plugs
6Reverse gate
7Ride plate
8Jet thrust nozzle
9Reboarding step
10Electric bilge pilot outlet
11Cleat
12Handgrip
UF1X71E0.book Page 21 Tuesday, September 26, 2006 9:52 AM
Page 30 of 108
Features and functions
23
Engine compartment
1Air filter case
2Water separator
3Fuel tank
4Battery
5Flushing hose connector
6Electrical box
7Oil tank
8Muffler
9Spark plugs/Spark plug caps/Ignition coils
10Spark plug lead
UF1X71E0.book Page 23 Tuesday, September 26, 2006 9:52 AM
Page 33 of 108
Features and functions
26
EJU31090Fuel tank filler cap
To remove the fuel tank filler cap, turn it coun-
terclockwise.
NOTE:
Make sure that the fuel tank filler cap is se-
curely closed before operating the watercraft.
EJU36270Remote control transmitter
The lock and unlock modes of the Yamaha
Security System are selected using the re-
mote control transmitter. (See “Yamaha Se-
curity System ” on page 33 for information on
using the remote control transmitter.)
CAUTION:
ECJ00930
The lock and unlock modes of the Yamaha
Security System can only be selected us-
ing the remote control transmitter. Ob-serve the following precautions to protect
your remote control transmitter:
Store the remote control transmitter
carefully so it will not be lost. When op-
erating the watercraft, use the transmit-
ter holder in the watertight
compartment. If you accidentally lose
your remote control transmitter, contact
a Yamaha dealer.
While the remote control transmitter has
been designed for use in wet environ-
ments, it should not be operated under-
water or submerged for an extended
length of time. If it gets wet, dry it with a
soft, dry cloth.
Keep the remote control transmitter
away from high temperatures and do not
place it in direct sunlight.
Do not drop the remote control transmit-
ter, subject it to strong shocks, or place
any heavy items on it.
Use a soft, dry cloth to clean the trans-
mitter. Do not use detergent, alcohol, or
other chemicals.
If the remote control transmitter needs a
new battery or is not operating properly,
contact a Yamaha dealer. Do not attempt
to replace the battery yourself.
1Fuel tank filler cap
1Transmitter holder
UF1X71E0.book Page 26 Tuesday, September 26, 2006 9:52 AM
Page 56 of 108
Operation
49
EJU31820
Fuel and oil
This watercraft is equipped with a 4-stroke en-
gine. Conventional 2-stroke engine oil cannot
be used.
The engine utilizes an electronic fuel injection
system to deliver the optimal air-fuel ratio re-
quired by the engine. By ensuring the optimal
combustion conditions, this system is able to
increase startability and improve fuel econo-
my.
EJU36330Gasoline
WARNING
EWJ00280
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
Stop the engine before refueling.
Refuel in a well-ventilated area with the
watercraft in a horizontal position.
Do not stand or sit on the watercraft
while refueling in case of fire.
Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.
Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level reaches approxi-
mately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do not
leave it in direct sunlight. Leave it in a
well-ventilated area with the watercraft
in a horizontal position.
Tighten the fuel tank filler cap securely
after refueling.
If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.
If any gasoline spills on your skin or
clothing, immediately wash the affected
area with soap and water and change
your clothes.
CAUTION:
ECJ00320
Do not use leaded gasoline. Leaded gas-
oline can seriously damage the catalytic
converter.
Use only fresh gasoline that has been
stored in clean containers.
EJU31860Gasohol
There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets the minimum octane ratings.
Gasohol containing methanol is not recom-
mended by Yamaha because it can cause
fuel system damage and engine performance
problems.Recommended gasoline:
Regular unleaded gasoline with a mini-
mum octane rating of
86 (Pump octane number) = (R +
M)/2
90 (Research octane number)
UF1X71E0.book Page 49 Tuesday, September 26, 2006 9:52 AM
Page 57 of 108
Operation
50
EJU31890Engine oil
Use a combination of the recommended SAE
and API engine oil classifications shown in the
chart below.
CAUTION:
ECJ00280
Use only 4-stroke engine oil.
EJU31950Filling the fuel tank
CAUTION:
ECJ00290
Be careful when refueling. Avoid getting
water and other contaminants in the fuel
tank. Contaminated fuel can cause poor
running and engine damage.
(1) Remove the seats. (See page 24 for seat
removal and installation procedures.)
(2) Remove the fuel tank filler cap, and then
slowly add fuel to the fuel tank. Stop filling
when the fuel level reaches approximate-ly 50 mm (2 in) from the top of the fuel
tank as indicated in the illustration.
(3) Install the fuel tank filler cap and the
seats.
1Approximately 50 mm (2 in) from top of the
fuel tank
Fuel tank capacity:
70 L (18.5 US gal) (15.4 Imp.gal)
UF1X71E0.book Page 50 Tuesday, September 26, 2006 9:52 AM
Page 60 of 108
Operation
53
EJU32280Pre-operation check points EJU32330Engine compartment
Ventilate the engine compartment before
each use.
To ventilate the engine compartment, remove
the seats. (See page 24 for seat removal and
installation procedures.) Leave the engine
compartment open for a few minutes to allow
any fuel vapors to escape.
While the engine compartment is open, check
for loose electrical connections.
WARNING
EWJ00460
Failure to ventilate the engine compart-
ment could result in a fire or explosion. Do
not start the engine if there is a fuel leak or
a loose electrical connection.
EJU32350Hull and deck
Check the hull and deck for cracks and other
damage. If any damage is found, have a
Yamaha dealer repair the watercraft.
EJU32380Fuel level
Check the fuel system for leakage, cracks,
and malfunctions before each use. (See page
83 for check points and correct procedures.)
(1) Remove the fuel tank filler cap to release
any pressure that might have built up in
the fuel tank.(2) Remove the seats. (See page 24 for seat
removal and installation procedures.)
(3) Check the fuel level in the fuel tank and
replenish if necessary. (See page 50 for
filling procedures.)
(4) Install the fuel tank filler cap and the
seats.
EJU32411Engine oil level
Check the engine oil level before each use.
CAUTION:
ECJ00390
When checking the engine oil level on
water, be careful of other watercraft,
boats, swimmers, and obstacles. The
water current and wind can cause the
watercraft to move and lead to a colli-
sion.
When checking the engine oil level on
land, supply water to the cooling water
passages. (See page 76 for procedures
on supplying water.)
Make sure that the engine has enough
oil, but do not overfill it. If there is too lit-
tle oil, the engine can be damaged. If
there is too much oil, the air filter can be-
come saturated with oil, permanently
damaging the filter and reducing engine
performance. Follow the checking pro-
cedure carefully.
Make sure that debris and water do not
enter the oil tank filler hole. Debris and
water in the engine oil can cause serious
engine damage.
To check the engine oil level:
(1) Place the watercraft in a horizontal posi-
tion or launch the watercraft, and then
start the engine.
(2) Run the engine at trolling speed for 6 min-
utes or more, and then stop the engine.
UF1X71E0.book Page 53 Tuesday, September 26, 2006 9:52 AM
Page 61 of 108
Operation
54
NOTE:
If the ambient temperature is 20 °C (68 °F) or
less, warm up the engine for an additional 5
minutes.
(3) Remove the seats. (See page 24 for seat
removal and installation procedures.)
(4) Remove the oil tank filler cap, wipe the
dipstick clean, and then screw the filler
cap into the filler hole completely. Re-
move the filler cap again and check that
the engine oil level is between the mini-
mum level mark and maximum level
mark on the dipstick.
(5) If the engine oil level is below the mini-
mum level mark, add enough oil so that
the oil level is between the minimum and
maximum level marks on the dipstick,and then install the filler cap. If the engine
oil level is significantly above the maxi-
mum level mark, the oil tank is overfilled.
Have a Yamaha dealer remove the ex-
cessive amount of engine oil.EJU32420Water separator
Check the water separator for water. The wa-
ter separator retains any water that may have
entered through the fuel tank breather hose if
the watercraft was capsized. Normally, the
water separator is empty.
If water remains in the water separator, drain
it by removing the drain screw. Place a drain
pan under the water separator to catch the
draining water or use a dry cloth to soak up
any water that could spill into the watercraft. If
any water spills into the watercraft, be sure to
wipe it up with a dry cloth. Also, be sure to in-
stall the drain screw after draining the water
separator.
EJU32450Bilge
Check the bilge for moisture and fuel residue.
This watercraft is equipped with a convention-
al jet vacuum bilge draining system and an
electric bilge draining system. The electric
bilge draining system is operated when the
engine is running. When excess water reach-
es the water inlet of the electric bilge pump,
1Oil tank filler cap
1Minimum level mark
2Maximum level mark
1Water separator
2Drain screw
UF1X71E0.book Page 54 Tuesday, September 26, 2006 9:52 AM
Page 83 of 108
Maintenance and care
76
EJU33490
Storage
WARNING
EWJ00330
Always place the watercraft upright in a
horizontal position when storing it, other-
wise fuel could leak out into the engine or
engine compartment, which could create a
fire hazard.
Storage for long periods of time, such as win-
ter storage, requires preventive maintenance
to ensure against deterioration. It is advisable
to have the watercraft serviced by a Yamaha
dealer prior to storage. However, the following
procedures can be performed by the owner.
EJU36371Flushing the cooling system
Flushing the cooling system is essential to
prevent it from clogging with salt, sand, or dirt.
CAUTION:
ECJ00971
Do not supply water to the cooling water
passages when the engine is not run-
ning. The water could flow back through
the muffler into the engine, causing se-
vere engine damage.
Do not run the engine for more than 15
seconds on land without supplying wa-
ter, otherwise the engine could over-
heat.
Do not run the engine over 6000 r/min on
land, otherwise the catalytic converter
could be seriously damaged.
(1) Remove the watercraft from the water
and place it in a horizontal position.
(2) Remove the rear seat and seat storage
compartment. (See page 24 for seat re-
moval and installation procedures.)
(3) Remove the flushing hose connector
cap, and then insert the garden hoseadapter into the flushing hose connector
and turn it until it is securely connected.
(4) Connect the garden hose adapter to a
water tap using a garden hose.
NOTE:
A garden hose is not included and must be
purchased separately.
(5) Start the engine, and then immediately
turn the water supply on until water flows
out continually from the jet thrust nozzle.
(6) Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn the
water supply off immediately and repeat
the above steps.
(7) Turn the water supply off, and then force
the remaining water out of the cooling
1Flushing hose connector cap
2Garden hose adapter
3Flushing hose connector
UF1X71E0.book Page 76 Tuesday, September 26, 2006 9:52 AM
Page 84 of 108
Maintenance and care
77
water passages by alternately squeezing
and releasing the throttle lever for 10 to
15 seconds, making sure not to run the
engine over 6000 r/min.
(8) Stop the engine.
(9) Remove the garden hose adapter and in-
stall the flushing hose connector cap.
EJU33600Lubrication
WARNING
EWJ00260
Do not spray flammable rust inhibitor
products on engine surfaces while the en-
gine is hot. The sprayed substance or pro-
pellants could catch fire.
(1) Remove the seats. (See page 24 for seat
removal and installation procedures.)
(2) Remove the air filter case cover and the
air filter element. (See page 84 for air fil-
ter case cover and air filter element re-
moval and installation procedures.)
(3) Spray a rust inhibitor into each intake
opening for 3 seconds.
(4) Install the air filter element in the air filter
case, and then install the air filter case
cover.
(5) Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:
ECJ00160
Do not run the engine for more than 15
seconds, otherwise the engine could over-
heat.
(6) Lubricate all cables such as the throttle
and steering cables.
NOTE:
Use a suitable marine grease applicator to
pressure-lubricate the cables and purge out
any moisture between the inner and outer ca-
bles.
(7) Lubricate the areas of the watercraft
specified in “Lubrication points” on page
87.
EJU36380Fuel system
WARNING
EWJ00280
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
Do not smoke when refueling, and keep
away from sparks, flames, and other
sources of ignition.
Stop the engine before refueling.
Refuel in a well-ventilated area with the
watercraft in a horizontal position.
Do not stand or sit on the watercraft
while refueling in case of fire.
Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags. Always properly dispose of
gasoline-soaked rags.
Avoid overfilling the fuel tank. Stop fill-
ing when the fuel level reaches approxi-
mately 50 mm (2 in) from the top of the
fuel tank. Fuel expands as it warms up
and could overflow if the fuel tank has
been overfilled. If temporarily leaving
the watercraft with a full fuel tank, do not
1Intake opening
UF1X71E0.book Page 77 Tuesday, September 26, 2006 9:52 AM