reset YAMAHA SVHO CRUISER 2011 Owners Manual

Instrument operation
39
EJU34906
Multifunction information
center
The multifunction information center displays
various watercraft information.
Multifunction information center initial op-
eration
When the multifunction information center is
activated, the analog speedometer/tachome-
ter makes one sweep, all of the display seg-
ments and indicator lights come on. After 2
seconds, the “WARNING” indicator light and
the warning indicators in the information dis-
play go off, and then the center starts to oper-
ate normally.
TIP:
The “UNLOCK” indicator light will go off when
the engine is started.
Multifunction information center standby
state
If the multifunction information center does
not receive any operation input within 25 sec-
onds after the engine stops, the center will
turn off and enter a standby state. When the
engine is started again, the displays return totheir state before the center turned off, and
then the center starts to operate normally.
EJU36794Analog speedometer/tachometer
The analog speedometer/tachometer has
both a speedometer function and a tachome-
ter function. By switching the meter, it can be
used as either a speedometer or a tachome-
ter.
TIP:
The analog speedometer is selected at the
Yamaha factory.
Analog speedometer
The analog speedometer shows the water-
craft speed against water.
The small outer numbers on the meter show
the watercraft speed in kilometers per hour
“km/h” and the large inner numbers show the
speed in miles per hour “mph”.
The “SPEED” indicator light comes on when
the analog speedometer is selected.
To switch to the speedometer from the ta-
chometer:
Push the “Speed/RPM” button for at least 1
second after the multifunction information
center is activated. When the meter switches
to the analog speedometer function, the
“SPEED” indicator light comes on if “km/h” are
selected as the display units. The “SPEED”
indicator light blinks three times, then comes
on, if “mph” are selected as the display units.
1“Volt/Hour” button
2“Speed/RPM” button
3Information display
4Analog speedometer/tachometer
5Multifunction display (FX Cruiser SHO)
6“Start/Stop” button (FX Cruiser SHO)
7“Mode/Reset” button (FX Cruiser SHO)
5431267
UF1W73E0.book Page 39 Monday, June 7, 2010 9:17 AM

Instrument operation
44
EJU35134Check engine warning
If a sensor malfunction or a short circuit is de-
tected, the check engine warning indicator
and the “WARNING” indicator light blink, and
the buzzer sounds intermittently.
If the check engine warning is activated, im-
mediately reduce the engine speed, return to
shore, and have a Yamaha dealer check the
engine.
TIP:
Push any button on the multifunction informa-
tion center to stop the buzzer.
EJU35037Multifunction display (FX Cruiser
SHO)
The multifunction display shows the following
information.
The display units of the multifunction display
are selected according to the display units of
the digital speedometer. (To change the dis-
play units, see page 40 for digital speedome-
ter display selection procedures.)
When “km/h” are selected as the display units
of the digital speedometer, values are shown
in kilometers/liters/degrees Celsius.When “mph” are selected as the display units
of the digital speedometer, values are shown
in miles/gallons/degrees Fahrenheit.
To switch the display mode, push the
“Mode/Reset” button for less than 1 second.
The display mode changes in the following or-
der.
Compass
This display shows the current direction of the
watercraft using the 8 major compass points.
TIP:
The accuracy of the compass varies depend-
ing on the operating conditions. Use this func-
tion as a reference only.
Average speed
This display shows the average speed in kilo-
meters per hour “AV KMH” or miles per hour
1Multifunction display
2“Start/Stop” button
3“Mode/Reset” button
UF1W73E0.book Page 44 Monday, June 7, 2010 9:17 AM

Instrument operation
46
Water temperature
This display shows the ambient water temper-
ature “L TEMP” (lake temperature).
Air temperature
This display shows the ambient air tempera-
ture “E TEMP” (environmental temperature).
Average speed/Tripmeter/Trip timer
modes
Average speed, distance traveled, and trip
time are recorded once the “Start/Stop” button
is pushed to start the measurements, regard-
less of the current display.
TIP:
The measurements are performed only while
the engine is running.
The measurements are not saved if the en-
gine is stopped. The measurements are resetautomatically when the displays go off 25 sec-
onds after the engine stops.
To start the measurements:
Push the “Start/Stop” button for less than 1
second. The beeper sounds once and the
measurements start.
To stop the measurements:
Push the “Start/Stop” button for less than 1
second while the measurements are being re-
corded. The beeper sounds once and the
measurements stop.
To restart the measurements:
Push the “Start/Stop” button for less than 1
second while the measurements are stopped.
The beeper sounds once and the measure-
ments restart.
To reset the measurements:
Push the “Mode/Reset” button for at least 2
seconds while the measurements are
stopped. The beeper sounds twice and the
measurements are reset.
1“Start/Stop” button
2“Mode/Reset” button
UF1W73E0.book Page 46 Monday, June 7, 2010 9:17 AM