oil YAMAHA TT600RE 2004 Service Manual

ILLUSTRATED SYMBOLS
The following symbols are not relevant to every
vehicle.
Illustrated symbols 1to 8are printed on the top
right of each page and indicate the subject of
each chapter.
1General information
2Specifications
3Periodic inspections and adjustments
4Chassis
5Engine
6Carburetor
7Electrical system
8Troubleshooting
Illustrated symbols 9to yare used to identify
the specifications appearing in the text.
9Can be serviced with engine mounted
0Filling fluid
qLubricant
wSpecial tool
eTorque
rWear limit, clearance
tEngine speed
yElectrical data
Illustrated symbols uto sin the exploded dia-
grams indicate the types of lubricants and lubrica-
tion points.
uApply engine oil
iApply gear oil
oApply molybdenum disulfide oil
pApply wheel bearing grease
aApply lightweight lithium-soap base grease
sApply molybdenum disulfide grease
Illustrated symbols dto fin the exploded dia-
grams indicate the following:
dApply locking agent (LOCTITE
®)
fReplace the part
GEN
INFOSPEC
INSP
ADJCHAS
ENGCARB
ELECTRBL
SHTG
New
12
34
?
56
78
90
qw
er
ty
uoi
psa
df
ProCarManuals.com

GEN
INFO
CHAPTER 1.
GENERAL INFORMATION
MOTORCYCLE IDENTIFICATION......................................................................................1-1
VEHICLE IDENTIFICATION NUMBER..........................................................................1-1
MODEL LABEL ..............................................................................................................1-1
IMPORTANT INFORMATION..............................................................................................1-2
PREPARATION FOR REMOVAL PROCEDURES ........................................................1-2
REPLACEMENT PARTS ..............................................................................................1-2
GASKETS, OIL SEALS AND O-RINGS ........................................................................1-2
LOCK WASHERS/PLATES AND COTTER PINS ........................................................1-3
BEARINGS AND OIL SEALS ........................................................................................1-3
CIRCLIPS ......................................................................................................................1-3
CHECKING OF CONNECTIONS........................................................................................1-4
SPECIAL TOOLS..................................................................................................................1-5
ProCarManuals.com

GEN
INFO
IMPORTANT INFORMATION
1-2
EB101000
IMPORTANT INFORMATION
PREPARATION FOR REMOVAL PROCEDURES
1. Remove all dirt, mud, dust and foreign materi-
al before removal and disassembly.
2. Use proper tools and cleaning equipment.
Refer to the “SPECIAL TOOLS” section.
3. When disassembling the machine, always
keep mated parts together. This includes
gears, cylinders, pistons and other parts that
have been “mated” through normal wear.
Mated parts must always be reused or
replaced as an assembly.
4. During machine disassembly, clean all parts
and place them in trays in the order of disas-
sembly. This will speed up assembly and
allow for the correct installation of all parts.
5. Keep all parts away from any source of fire.
EB101010
REPLACEMENT PARTS
1. Use only genuine Yamaha parts for all
replacements. Use oil and grease recom-
mended by Yamaha for all lubrication jobs.
Other brands may be similar in function and
appearance, but inferior in quality.
EB101020
GASKETS, OIL SEALS AND O-RINGS
1. Replace all gaskets, seals and O-rings when
overhauling the engine. All gasket surfaces,
oil seal lips and O-rings must be cleaned.
2. Properly oil all mating parts and bearings dur-
ing reassembly. Apply grease to the oil seal
lips.
ProCarManuals.com

GEN
INFO
IMPORTANT INFORMATION
1-3
EB101030
LOCK WASHERS/PLATES AND COTTER PINS
1. Replace all lock washers/plates 1and cotter
pins after removal. Bend lock tabs along the
bolt or nut flats after the bolt or nut has been
tightened to specification.
EB101040
BEARINGS AND OIL SEALS
1. Install bearings and oil seals so that the man-
ufacturer’s marks or numbers are visible.
When installing oil seals, apply a light coating
of lightweight lithium base grease to the seal
lips. Oil bearings liberally when installing, if
appropriate.
1Oil seal
Do not use compressed air to spin the bear-
ings dry. This will damage the bearing sur-
faces.
1Bearing
CAUTION:
EB101050
CIRCLIPS
1. Check all circlips carefully before reassembly.
Always replace piston pin clips after one use.
Replace distorted circlips. When installing a
circlip 1, make sure that the sharp-edged
corner 2is positioned opposite the thrust 3
it receives. See sectional view.
4Shaft
OR
ProCarManuals.com

1-8
GEN
INFO
SPECIAL TOOLS
Tool No.Tool name / Usage Illustration
90890-11043DU bush/oil seal guide
This tool is used to install the DU bush and
the fork oil seal.
90890-01326T-handle
This tool is needed to loosen and tighten the
front fork damper rod holding bolt.
90890-01460Front fork damper rod holder
This tool is needed to hold the front fork
damper rod when loosening and tightening
the holding bolt.
ProCarManuals.com

SPECGENERAL SPECIFICATIONS
2-1
SPECIFICATIONS
GENERAL SPECIFICATIONS
Item Standard Limit
ModelTT600RE: 5CH5
Dimensions
Overall length 2,220 mm •••
Overall width 865 mm •••
Overall height 1,195 mm •••
Seat height 890 mm •••
Wheelbase 1,480 mm •••
Ground clearance 280 mm •••
Minimum turning radius 3,300 mm (right)
3,100 mm (left) •••
Basic weight (with oil and full
fuel tank)164.5 kg •••
Engine
Engine type Air cooled 4-stroke, SOHC
Cylinder arrangement Forward inclined single cylinder
Displacement 595 cm
3•••
Bore x stroke 95.0 x 84.0 mm •••
Compression ratio 8.5 : 1 •••
Starting system Electric starter
Lubrication system Dry sump with separate oil tank
Engine oil
Type
Temp. °CSAE20W40SE or SAE10W30SE •••
Recommended engine oil classification API Service SE, SF, SG or higher •••
Quantity:
Without oil filter cartridge
replacement 2.4 L •••
With oil filter cartridge
replacement 2.5 L •••
Total amount (dry engine) 3.0 L •••
Air filterWet type element
Fuel
Type Regular unleaded gasoline
Fuel tank capacity 10 L •••
Fuel reserve amount 3.0 L •••
Carburetor
Manufacturer TEIKEI
Model x quantity Y30PV-2ATK x 1
ProCarManuals.com

SPECGENERAL SPECIFICATIONS
2-3
Item Standard Limit
Brakes
Front:
Type Single Ø 267 mm disk brake,
2 x 28 mm
Operation Right hand
Fluid DOT 4
Rear:
Type Single Ø 220 mm disk brake,
1 x 34 mm caliper
Operation Right foot
Fluid DOT 4
Suspension
Front Telescopic fork Outside tube
dia. 46 mm
Rear Deltabox Swingarm with
adjustable shock absorber
Spring/shock absorber
Front Coil spring / oil damper
RearCoil spring / gas-oil damper, spring
preload adjustable
Wheel travel
Front 230 mm •••
Rear 230 mm •••
Electrical system
Ignition system Transistorized coil ignition (digital)
Charging system:
Type A.C. magneto
Standard output 14V, 13.5A at 5.000 r/min •••
Battery:
Model GT9B-4
Voltage, capacity 12V, 8Ah •••
Headlight typeQuartz bulb (halogen)
Bulb voltage, wattage x quantity
Headlight 12V 60W / 55W x 1 •••
Tail/brake light 12V 5W / 21W x 1 •••
Turn signal light 12V 10W x 4 •••
Auxiliary light 12V 5W x 1 •••
Meter lighting 12V 3W x 1 •••
Turn signal indicator light 12V 1.2W x 1 •••
Neutral indicator light 12V 1.2W x 1 •••
Auxiliary indicator light 12V 1.2W x 1 •••
High beam indicator light 12V 1.2W x 1 •••
Fuse20A •••
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-7
Item Standard Limit
Piston ring
Top ring:
Ring type Barrel
Dimensions (B x T) 1.20 x 3.80 mm •••
End gap
(installed) 0.30 - 0.45 mm 0.70 mm
Ring side clearance 0.040 - 0.080 mm 0.130 mm
2
ndring:
Ring type Plain
Dimensions (B x T) 1.20 x 3.80 mm •••
End gap
(installed) 0.30 - 0.45 mm 0.80 mm
Ring side clearance 0.030 - 0.070 mm 0.130 mm
Oil ring:
Dimensions (B x T) 2.50 x 3.40 mm •••
End gap
(installed) 0.20 - 0.70 mm •••
Ring side clearance 0.020 - 0.060 mm •••
Crankshaft
Width A 74.95 - 75.00 mm •••
Max. runout C ••• 0.030 mm
Big end side clearance D 0.350 - 0.650 mm •••
Big end radial clearance 0.010 - 0.025 mm •••
Small end free play F 0.80 mm •••
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-8
Item Standard Limit
Ballancer
Ballancer drive method Gear
Clutch
Clutch release method Inner push, cam push
Friction plate thickness 2.72 - 2.88 mm •••
Wear limit ••• 2.60 mm
Plate quantity 6 pcs
Friction plate thickness 2.94 - 3.06 mm •••
Wear limit ••• 2.8 mm
Plate quantity 2 pcs
Clutch plate thickness 1.20 mm •••
Plate quantity 7 pcs
Max. warpage ••• 0.20 mm
Clutch spring free length 42.8 mm •••
Plate quantity 5 pcs
Clutch housing thrust clearance 0.070 - 0.071 mm •••
Transmission
Max. main axle runout ••• 0.08 mm
Max. drive axle runout ••• 0.08 mm
Shift mechanism type Cam drum and guide bar
Carburetor
ID mark 5CH5 10
Main jet #1:#150 #2:#145
Main air jet #1:1.0 #2:0.9
Jet needle #1:5C5A-3/5 #2:5Y18-3/5
Needle jet 2.600
Cutaway 4.00
Pilot air jet 1 # 0.8 mm
Pilot jet # 50
Bypass 1 # 1.0
Pilot screw turns out 2-3/4 +/- 1/2
Valve seat size 2.5
Starter jet 1 # 74
Float height 6.0 - 8.0 mm •••
Engine idle speed1,150-1,450 r/min •••
CO% 1.5 - 3 •••
Intake vacuum 30.6-33.36 kPa - 230-250 mm Hg •••
Lubrication systemDry sump
Oil filter type Paper type
Oil pump:
Oil pump type Trochoid type
Inner rotor to outer rotor tip clearance 0.12 mm 0.20 mm
Outer rotor to pump housing
clearance 0.030 - 0.080 mm 0.150 mm
Bypass valve opening pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm
2) •••
Relief valve operating pressure 80.0 - 120.0 kPa (0.8 - 1.2 kgf/cm2) •••
Oil pressure (hot) 13.0 kPa (0.13 kgf/cm2)/1,300 r/min •••
Pressure check location Oil filter chamber •••
ProCarManuals.com

SPECMAINTENANCE SPECIFICATIONS
2-10
Tightening
Part torque
Part to be tightened
nameThread size Remarks
Nm mkg
Cylinder head Washer
based bol M8 x 1.25 29 2.9
Cylinder head Stud bolt M10 x 1.25 20 2.0
Cylinder head Hexagon socket
head screw M6 x 1.0 10 1.0
Cylinder head Stud bolt M6 x 1.0 7 0.7
Cylinder head:
Cap (oil check) Union bolt M6 x 1.0 7 0.7
Spark plug – M12 x 1.25 18 1.8
Cylinder head cover Hexagon socket
head screw M6 x 1.0 10 1.0
Tappet cover (intake) Hexagon socket
head screw M6 x 1.0 10 1.0
Tappet cover (exhaust) – M32 x 1.5 12 1.2
Cylinder Crown nut M8 x 1.25 22 2.2
Cylinder Nut M10 x 1.25 42 4.2
Cylinder Hexagon socket
head screw M6 x 1.0 10 1.0
Weight drive gear Hexagon nut M16 x 1.0 60 6.0
Rotor (A.C. magneto) Hexagon nut M14 x 1.5 120 12.0
Lock nut (valve adjusting screw) Hexagon nut M6 x 1.0 14 1.4
Cam chain sprocket Washer based
bolt M7 x 1.0 20 2.0
Cam chain stopper guide Hexagon socket
head screw M6 x 1.0 10 1.0
Cam chain stopper guide Washer based
screw M16 x 1.0 20 2.0
Rocker shaft Hexagon socket
head screw M6 x 1.0 10 1.0
Oil pump Hexagon socket
head screw M6 x 1.0 10 1.0
Oil delivery/retrieval pipe Pan screw M6 x 1.0 7 0.7
Oil draining pipe Washer based
screw M14 x 1.5 30 3.0
Oil filter cover Hexagon socket
head screw M6 x 1.0 10 1.0
Bleed screw (oil filter cover) Hexagon screw M5 x 0.8 5 0.5
Push lever (clutch) Pan screw M8 x 1.0 12 1.2
Push rod (clutch) Hexagon nut M6 x 1.0 8 0.8
Sprocket Hexagon nut M18 x 1.0 115 11.5
Lock washer (oil seal) Hexagon screw M6 x 1.0 10 1.0
Stop lever Bolt M6 x 1.0 10 1.0
Shift cam Hexagon screw M6 x 1.0 10 1.0
Stator Pan head (+)
screw M5 x 0.8 5 0.5
Tightening torques
ProCarManuals.com