check engine light YAMAHA XV535 2001 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2001, Model line: XV535, Model: YAMAHA XV535 2001Pages: 96, PDF Size: 10.38 MB
Page 32 of 96
5-1
5
EAU00372
5-OPERATION AND IMPORTANT RIDING POINTS
EAU00373
WARNING
@ l
Become thoroughly familiar
with all operating controls and
their functions before riding.
Consult a Yamaha dealer re-
garding any control or function
that you do not thoroughly un-
derstand.
l
Never start the engine or oper-
ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con-
sciousness and death within a
short time. Always make sure
that there is adequate ventila-
tion.
l
Before starting out, make sure
that the sidestand is up. If the
sidestand is not raised com-
pletely, it could contact the
ground and distract the opera-
tor, resulting in a possible loss
of control.
@
EAU02997*
Starting a cold engine In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:l
The transmission is in the neutral
position.
l
The transmission is in gear with
the clutch lever pulled and the
sidestand up.
EW000054
WARNING
@ l
Before starting the engine,
check the function of the igni-
tion circuit cut-off system ac-
cording to the procedure
described on page 3-11.
l
Never ride with the sidestand
down.
@
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
2. Shift the transmission into the neu-
tral position.NOTE:@ When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical
circuit. @3. Turn the starter (choke) on and
completely close the throttle. (See
page 3-6 for starter (choke) opera-
tion.)
4. Start the engine by pushing the
start switch.NOTE:@ If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre-
serve the battery. Do not crank the en-
gine more than 10 seconds on any one
attempt. @
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM
Page 37 of 96
6
PERIODIC MAINTENANCE AND MINOR REPAIR
Owner’s tool kit .................................................... 6-1
Periodic maintenance and lubrication chart ......... 6-2
Checking the spark plugs .................................... 6-5
Engine oil and oil filter element ............................ 6-7
Final gear oil ........................................................ 6-9
Cleaning the air filter element ............................ 6-11
Adjusting the carburetors .................................... 6-13
Adjusting the engine idling speed ....................... 6-13
Adjusting the throttle cable free play ................... 6-14
Adjusting the valve clearance ............................. 6-14
Tires ................................................................... 6-15
Spoke wheels ..................................................... 6-17
Adjusting the clutch lever free play .................... 6-18
Adjusting the brake lever free play ...................... 6-19
Adjusting the brake pedal position and
free play ........................................................... 6-19
Adjusting the rear brake light switch ................... 6-21
Checking the front brake pads and rear
brake shoes ..................................................... 6-21
Checking the brake fluid level ............................ 6-22
Changing the brake fluid ..................................... 6-23Checking and lubricating the cables .................. 6-23
Checking and lubricating the throttle
grip and cable .................................................. 6-24
Checking and lubricating the brake and
shift pedals ...................................................... 6-25
Checking and lubricating the brake and
clutch levers ..................................................... 6-25
Checking and lubricating the sidestand ............. 6-25
Lubricating the rear suspension ........................ 6-26
Checking the front fork ....................................... 6-27
Checking the steering ........................................ 6-27
Checking the wheel bearings ............................. 6-28
Battery ............................................................... 6-29
Replacing the fuses .......................................... 6-31
Replacing the headlight bulb .............................. 6-31
Replacing a turn signal light bulb or the
tail/brake light bulb ........................................... 6-33
Supporting the motorcycle ................................ 6-33
Front wheel ....................................................... 6-34
Rear wheel ........................................................ 6-35
Troubleshooting .................................................. 6-37
Troubleshooting chart ........................................ 6-38
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM
Page 42 of 96
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
6
EAU01486
Checking the spark plugs The spark plugs are important engine
components, which are easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plugs should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
the condition of the spark plugs can re-
veal the condition of the engine.
To remove a spark plug
1. Remove the appropriate spark
plug cover (rear right or front left)
by removing the screws.
2. Remove the spark plug cap.3. Remove the spark plug as shown,
with the spark plug wrench includ-
ed in the owner’s tool kit.To check the spark plugs
1. Check that the porcelain insulator
around the center electrode on
each spark plug is a medium-to-
light tan (the ideal color when the
motorcycle is ridden normally).
2. Check that all spark plugs installed
in the engine have the same color.
NOTE:@ If any spark plug shows a distinctly dif-
ferent color, the engine could be defec-
tive. Do not attempt to diagnose such
problems yourself. Instead, have a
Yamaha dealer check the motorcycle. @3. Check each spark plug for elec-
trode erosion and excessive car-
bon or other deposits, and replace
it if necessary.
1. Spark plug cover
2. Screw (´ 2)
1. Spark plug wrench
Specified spark plug:
BPR6ES (NGK) or
W20EPR-U (DENSO)
E_3bt.book Page 5 Thursday, September 7, 2000 10:01 AM
Page 44 of 96
PERIODIC MAINTENANCE AND MINOR REPAIR
6-7
6
EAU02942
Engine oil and oil filter
element The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele-
ment replaced at the intervals specified
in the periodic maintenance and lubri-
cation chart.
To check the engine oil level
1. Place the motorcycle on a level
surface and hold it in an upright
position.NOTE:@ Make sure that the motorcycle is posi-
tioned straight up when checking the oil
level. A slight tilt to the side can result in
a false reading. @2. Start the engine, warm it up for
several minutes, and then turn it
off.3. Wait a few minutes until the oil set-
tles, and then check the oil level
through the check window located
at the bottom-left side of the crank-
case.
NOTE:@ The engine oil should be between the
minimum and maximum level marks. @4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.To change the engine oil
(with or without oil filter element
replacement)
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.1. Engine oil level check window
2. Maximum level mark
3. Minimum level mark
1. Engine oil filler cap
E_3bt.book Page 7 Thursday, September 7, 2000 10:01 AM
Page 46 of 96
PERIODIC MAINTENANCE AND MINOR REPAIR
6-9
6
NOTE:@ Make sure that the O-ring is properly
seated. @7. Install the engine oil drain bolt, and
then tighten it to the specified
torque.
8. Add the specified amount of the
recommended engine oil, and
then install and tighten the oil filler
cap.
EC000067
CAUTION:@ If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha deal-
er check the vehicle. @9. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
10. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU03714
Final gear oil The final gear case must be checked
for oil leakage before each ride. If any
leakage is found, have a Yamaha deal-
er check and repair the motorcycle. In
addition, the final gear oil level must be
checked and the oil changed as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
EW000066
WARNING
_ l
Make sure that no foreign mate-
rial enters the final gear case.
l
Make sure that no oil gets on
the tire or wheel.
_
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kg)
Recommended engine oil:
See page 8-1.
Oil quantity:
Without oil filter element
replacement:
2.6 L
With oil filter element
replacement:
2.8 L
Total amount (dry engine):
3.2 L
E_3bt.book Page 9 Thursday, September 7, 2000 10:01 AM
Page 47 of 96
PERIODIC MAINTENANCE AND MINOR REPAIR
6-10
6 To check the final gear oil level
1. Place the motorcycle on a level
surface and hold it in an upright
position.
NOTE:_ l
The final gear oil level must be
checked on a cold engine.
l
Make sure that the motorcycle is
positioned straight up when
checking the oil level. A slight tilt to
the side can result in a false
reading.
_2. Remove the oil filler bolt, and then
check the oil level in the final gear
case.
NOTE:_ The oil level should be at the brim of
the filler hole. _3. If the oil is below the brim of the fill-
er hole, add sufficient oil of the rec-
ommended type to raise it to the
correct level.
To change the final gear oil
1. Place an oil pan under the final
gear case to collect the used oil.
2. Remove the oil filler bolt and drain
bolt to drain the oil from the final
gear case.
3. Install the final gear oil drain bolt,
and then tighten it to the specified
torque.
4. Add the recommended final gear
oil to the brim of the filler hole.
NOTE:_ GL4 is a quality rating. Hypoid gear oils
rated GL5 or GL6 may also be used. _5. Install and tighten the filler bolt.
6. Check the final gear case for oil
leakage. If oil is leaking, check for
the cause.
1. Final gear oil filler bolt
2. Correct oil level
3. Final gear oil drain bolt
Tightening torque:
Final gear oil drain bolt:
23 Nm (2.3 m·kg)
Recommended final gear oil:
Hypoid gear oil SAE 80 (API GL4)
or multi-grade hypoid gear oil
SAE 80W-90
Oil quantity:
0.19 L
E_3bt.book Page 10 Thursday, September 7, 2000 10:01 AM
Page 70 of 96
PERIODIC MAINTENANCE AND MINOR REPAIR
6-33
6
EAU00855
Replacing a turn signal light
bulb or the tail/brake light
bulb1. Remove the lens by removing the
screws.2. Remove the defective bulb by
pushing it in and turning it counter-
clockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
EC000108
CAUTION:@ Do not overtighten the screws, oth-
erwise the lens may break. @
EAU01579
Supporting the motorcycle Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other mainte-
nance requiring the motorcycle to
stand upright. Check that the motor-
cycle is in a stable and level position
before starting any maintenance. A
strong wooden box can be placed un-
der the engine for added stability.
To service the front wheel
1. Stabilize the rear of the motorcycle
by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.
2. Raise the front wheel off the
ground by using a motorcycle
stand.
1. Screw (´ 2)
1. Tail/brake light bulb (´ 2)
E_3bt.book Page 33 Thursday, September 7, 2000 10:01 AM
Page 92 of 96
10-INDEXAAir filter element, cleaning ...................... 6-11BBattery ................................................... 6-29
Brake and clutch levers, checking and
lubricating ............................................ 6-25
Brake and shift pedals, checking and
lubricating ............................................ 6-25
Brake fluid, changing ............................. 6-23
Brake fluid level, checking...................... 6-22
Brake lever...............................................3-4
Brake lever free play, adjusting .............. 6-19
Brake light switch, adjusting ................... 6-21
Brake pads and shoes, checking ........... 6-21
Brake pedal..............................................3-4
Brake pedal position and free play,
adjusting .............................................. 6-19CCables, checking and lubricating............ 6-23
Carburetors, adjusting............................ 6-13
Care.........................................................7-1
Clutch lever ..............................................3-3
Clutch lever free play, adjusting ............. 6-18
Conversion table ......................................8-5DDimmer switch .........................................3-2
EEngine break-in ....................................... 5-4
Engine oil and oil filter element ................ 6-7
Engine stop switch................................... 3-3FFinal gear oil ............................................ 6-9
Front fork, checking ............................... 6-27
Fuel ......................................................... 3-5
Fuel consumption, tips for reducing ......... 5-4
Fuel reserve switch.................................. 3-3
Fuel tank cap ........................................... 3-5
Fuses, replacing .................................... 6-31HHandlebar switches ................................. 3-2
Headlight bulb, replacing ....................... 6-31
Helmet holder .......................................... 3-9
High beam indicator light ......................... 3-1
Horn switch ............................................. 3-2IIdentification numbers ............................. 9-1
Idling speed, adjusting ........................... 6-13
Ignition circuit cut-off system.................. 3-10
Indicator lights ......................................... 3-1KKey identification number ........................ 9-1
LLight switch ..............................................3-3MMain switch ..............................................3-1
Model label ..............................................9-2NNeutral indicator light ...............................3-1PParking.....................................................5-5
Part locations ...........................................2-1
Pass switch ..............................................3-2
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1SSafety information ....................................1-1
Seats .......................................................3-7
Passenger seat...................................3-7
Rider seat ...........................................3-8
Shifting .....................................................5-3
Shift pedal ................................................3-4
Shift points (for Switzerland only) .............5-3
Shock absorber assemblies, adjusting .....3-9
Sidestand ...............................................3-10
Sidestand, checking and lubricating .......6-25
E_3bt.book Page 1 Thursday, September 7, 2000 10:01 AM
Page 93 of 96
INDEX
Spark plugs, checking ............................. 6-5
Specifications .......................................... 8-1
Speedometer unit .................................... 3-2
Starter (choke) lever ................................ 3-6
Starting a cold engine .............................. 5-1
Starting a warm engine ............................ 5-2
Start switch .............................................. 3-3
Steering, checking ................................. 6-27
Steering lock............................................ 3-7
Storage.................................................... 7-4
Supporting the motorcycle ..................... 6-33
Suspension (rear), lubricating ................ 6-26TThrottle cable free play, adjusting .......... 6-14
Throttle grip and cable, checking and
lubricating............................................ 6-24
Tires ...................................................... 6-15
Tool kit..................................................... 6-1
Troubleshooting..................................... 6-37
Troubleshooting chart ............................ 6-38
Turn signal indicator light ......................... 3-1
Turn signal or tail/brake light bulb,
replacing ............................................. 6-33
Turn signal switch .................................... 3-2VValve clearance, adjusting ..................... 6-14
Vehicle identification number ................... 9-1
WWheel bearings, checking ..................... 6-28
Wheel (front) ......................................... 6-34
Installing .......................................... 6-35
Removing ........................................ 6-34
Wheel (rear) .......................................... 6-35
Installing .......................................... 6-37
Removing ........................................ 6-35
Wheels .................................................. 6-17
E_3bt.book Page 2 Thursday, September 7, 2000 10:01 AM