drain bolt Acura CL 2002 Owner's Manual

Always change the oil and f ilter
accordingtothetimeanddistance
(miles/kilometers) recommenda-
tions in the maintenance schedule.
The oil and f ilter collect contami-
nants that can damage your engine if
they are not removed regularly.Run the engine until it reaches
normal operating temperature,
then shut it off.
Open the hood and remove the
engine oil f ill cap. Remove the oil
drain bolt and washer f rom the
bottom of the engine. Drain the oil
into an appropriate container.Remove the oil f ilter and let the
remaining oil drain. A special
wrench (available f rom your Acura
dealer) is required to remove the
f ilter.
Changing the oil and f ilter requires
special tools and access f rom
underneath the car. The car should
be raised on a service station-type
hydraulic lif t f or this service. Unless
you have the knowledge and proper
equipment, you should have this
maintenance done by a skilled
mechanic.
1.
2.3.
CONT INUED
Changing the Oil and Filter
Engine Oil
Maint enance221
W WA
AS
SHH E
ER
R O
OI
ILL D
DR
RAA I
INN
B
BO OL LTT O
OI
ILL F
FIILLT T E
ER
R

Let the engine run f or several
minutes and check the drain bolt
and oil f ilter f or leaks.
Turn of f the engine, let it sit f or
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the
dipstick.
Install a new oil f ilter according to
instructions that come with it.
Put a new washer on the drain bolt,
then reinstall the drain bolt.
Tighten it to:
Refill the engine with the recom-
mended oil.
Engine oil change capacity
(including f ilter):
Replace the engine oil f ill cap.
Start the engine. The oil pressure
indicator light should go out within
f ive seconds. If it does not, turn of f
the engine and reinspect your
work.
6. 7.
8.
9.
4.
5.
Engine Oil
Maint enance222
29 lbf·ft (39 N·m , 4.0 kgf·m)
4.6 US qt (4.4
, 3.9 Imp qt)
Improper disposal of engine oil can be
harmf ul to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling
center. Do not discard it in a trash bin
or dump it on the ground.

Install a rubber hose on the drain
bolt at the rear of the engine
cylinder block. Loosen the drain
bolt.Bef ore removing the reserve tank,
remove the cruise control cable
f rom its clip, then remove the
ground cable f rom the clip on the
reserve tank. To remove the
cruise control cable, pivot the
upper part of the clip and push
down the lower part slightly.
Drain the coolant into an
appropriate container. Remove the reserve tank f rom its
holder by pulling it straight up.
Drain the coolant into an
appropriate container, then put the
tank back in its holder.
Af ter installing the tank back in
place, put the cables back in their
clips.
5.
4. 6.
Cooling Syst em
Maint enance226
H HO
OL LDD E
ER
R
D
D R
RAA I
INN B
BOOL LTT R
RU
UB BBBEER
R
H
H O
OS SEE
R
REES
SE ER
RV V E
E T
TA
A N
NK K C
CAA P
P
C
CR RUUI ISSE E C
COON NTTR
RO OL L C
CAA B
BLLEE R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K

CONT INUED
Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
When the coolant stops draining,
tightenthedrainplugatthe
bottom of the radiator.
Tighten the drain bolt at the rear
of the engine cylinder block
securely.
Tightening torque:
Pour Honda All Season
Antif reeze/Coolant Type 2 into
the radiator up to the base of the
f iller neck. This coolant is a
mixture of 50 percent antif reeze
and 50 percent water. Pre-mixing
is not required.
The cooling system capacity is:
Start the engine and let it run f or
about 30 seconds. Then turn of f
the engine. Pour coolant into the
radiator up to the base of the f iller
neck.
7.
8.
9.10.
Cooling Syst em
Maint enance227
F FIILLL LEE R
R N
NEEC
CK K
F
Fi illll u
u p
p t
too h
he
erree R
RE
ES
SE ER
RV V E
E T
TA
A N
NK K
7 lbf·ft (10 N·m , 1.0 kgf·m)
1.48 US gal (5.6
, 1.23 Imp gal)