hood open ACURA CSX 2006 Service Owner's Manual



(#'

 )
20-15320-153
Hood Seal Replacement
Fastener Locations : Clip, 7
A
B B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts. 1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal, and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
ProCarManuals.com
DYNOMITE -2009-



(#'

 )
20-15320-153
Hood Seal Replacement
Fastener Locations : Clip, 7
A
B B
6. Check that the hood opens properly and closes
securely.
7. Apply touch-up paint to the hinge mounting bolts and around the hinges, and let the paint dry.
8. Apply multipurpose grease to the hood latch and hood hinges as indicated by the arrows.
9. Reinstall all of the removed parts. 1. Detach the clips with a clip remover, then remove
the hood seal (A) and hood corner seals (B). Take
care not to scratch the hood.
2. Install the seals in the reverse order of removal, and if the clips are damaged or stress-whitened,
replace them with new ones.
08/08/21 15:04:56 61SNR030_200_0155
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

)
20-177
Openers
Component Location Index
TRUNK LID LOCK CYLINDER
TRUNK LID LATCH
FUEL FILL
DOOR LATCH
TRUNK LID OPENER CABLE/
FUEL FILL DOOR OPENER CABLE
HOOD OPENER CABLE HOOD LATCH
TRUNK LID OPENER/
FUEL FILL DOOR OPENER
HOOD RELEASE HANDLE Replacement, page 20-184
Replacement,page 20-185
Replacement, page 20-179
Replacement, page 20-178 Replacement, page 20-181
Replacement, page 20-182
08/08/21 15:05:10 61SNR030_200_0179
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
20-178Openers
Hood Opener Cable Replacement
Fastener Locations
A
B
D
E EG
C
C 6x1.0mm
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
E E
D
F
:Bolt,2
C
:Clip,4
E :Clip,1
F
NOTE:
 Put on gloves to protect your hands.
 Take care not to scratch the body and related parts.
1. Remove these items:  Front grille cover (see page 20-163)
 Front inner fender, driver’s side (see page 20-171)
 Kick panel, driver’s side (see page 20-66)
2. Disconnect the hood opener cable (A) from the hood latch (B) (see page 20- 181), and remove the bolts (C), then
remove the hood release handle (D). Take care not to kink the cable.
3. Detach the clips (E) with a clip remover, release the hood opener cable from the clip (F), and remove the grommet (G) from the body, then remove the hood opener cable from the vehicle. Take care not to kink the cable.
4. Install the cable in the reverse order of removal, and if the clips are damaged or stress-whitened, replace them with new ones.
08/08/21 15:05:10 61SNR030_200_0180
ProCarManuals.com
DYNOMITE -2009-



(#'


 )
20-181
Hood Latch Replacement
Fastener Locations 6x1.0mm
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
A
B
C
D
:Bolt,3
1. Remove the front grille cover (see page 20-163).
2. With hood latch switch: Remove the clip (A), then
disconnect and detach the hood latch switch
connector (B).
3. Remove the bolts, then remove the hood latch (C) from the body, and disconnect the hood opener
cable (D) from the hood latch. 4. Install the latch in the reverse order of removal, and
note these items:
 Apply multipurpose grease to each location of the hood latch indicated by the arrows.
 Make sure the hood opener cable is connected properly and the hood latch switch connector is
plugged in properly (for some models).
 Adjust the hood latch alignment (see step 4 on page 20-152).
 Make sure the hood opens properly and locks securely.
08/08/21 15:05:33 61SNR030_200_0183
ProCarManuals.com
DYNOMITE -2009-



µ
µ
µ
µ µ
µ
µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
YES
NO
21-49
BLU
YEL
BLU YEL
POWER TRANSISTOR 4P CONNECTOR
CLIMATE CONTROL UNIT 32P CONNECTOR
BLU
YEL
CLIMATE CONTROL UNIT 32P CONNECTOR
BLOWER MOTOR 2P CONNECTOR
WHT
19. Check for continuity between the followingterminals of the climate control unit 32P connector
and the power transistor 4P connector.
32P: 4P:
No. 13 No. 1
No. 14 No. 3
Go to step 20.
Repair open in the wire(s) between the
climate control unit and the power transistor.
20. Turn the ignition switch to ON (II).
21. Measure the voltage between body ground and the climate control unit 32P connector terminals No. 13
and No. 14 individually.
Repair short to power in the wire(s).
Go to step 22. 22. Reconnect the climate control unit 32P connector.
23. Test the power transistor (see page 21-71).
Check for loose wires or poor connections at
the climate control unit 32P connector and at the
power transistor 4P connector. If the connections
are good, substitute a known-good climate control
unit, and recheck. If the symptom/indication goes
away, replace the original climate control unit.
Replace the power transistor.
24. Disconnect the jumper wire.
25. Disconnect the blower motor 2P connector.
26. Measure the voltage between the blower motor 2P connector terminal No. 1 and body ground.
Replace the blower motor.
Go to step 27.
27. Turn the ignition switch to LOCK (0).
28. Remove the blower motor relay from the under- hood fuse/relay box, and test it (see page 22-70).
Go to step 29.
Replace the blower motor relay.
(cont’d)
Wire side of female terminalsWire side of female terminals
Wire side of female terminals
Wire side of female terminals
Is there continuity?
Is there voltage? Is the power transistor OK ?
Is there battery voltage?Is the relay OK ?
08/08/21 14:42:22 61SNR030_210_0050
ProCarManuals.com
DYNOMITE -2009-




µ
µ
µ
µ µ
µ
YES
NO
YES
NO YES
NO
21-50Climate Control
DTC Troubleshooting (cont’d)
BLOWER MOTOR RELAY 4P SOCKET
BLOWER MOTOR RELAY 4P SOCKET
BRN BLOWER MOTOR RELAY 4P SOCKET
BLK
29. Measure the voltage between the blower motorrelay 4P socket terminal No. 1 and body ground.
Go to step 30.
Replace the under-hood fuse/relay box
(see page 22-65).
30. Turn the ignition switch to ON (II).
31. Measure the voltage between the blower motor relay 4P socket terminal No. 3 and body ground.
Go to step 32.
Repair open in the wire between the No. 36
(10 A) fuse in the under-dash fuse/relay box and the
blower motor relay. 32. Turn the ignition switch to LOCK (0).
33. Check for continuity between the blower motor
relay 4P socket terminal No. 4 and body ground.
Repair open in the WHT wire between the
blower motor relay and the blower motor.
Check for an open in the wire between the
blower motor relay and body ground. If the wire is
OK, check for poor ground at G301 (see page 22-64).
Is there battery voltage?
Is there battery voltage? Is there continuity?
08/08/21 14:42:23 61SNR030_210_0051
ProCarManuals.com
DYNOMITE -2009-



µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO YES
NO
YES
NO
21-58
Climate Control
Radiator and A/C Condenser Fan Low Speed Circuit Troubleshooting
(cont’d)
RADIATOR FAN 2P CONNECTOR
BRN
RADIATOR FAN 2P CONNECTOR RED
JUMPER WIRE FAN CONTROL RELAY 5P SOCKET
RED
23. Measure the voltage between the radiator fan 2Pconnector terminal No. 2 and body ground.
Go to step 24.
Repair open in the wire between the radiator
fan relay and the radiator fan.
24. Set the A/C button and fan control dial OFF, then turn the ignition switch to LOCK (0).
25. Reconnect the radiator fan 2P connector.
26. Connect the radiator fan 2P connector terminal No. 1 to body ground with a jumper wire.
27. Turn the ignition switch to ON (II), then set the A/C button and fan control dial ON.
Go to step 28.
Replace the radiator fan motor. 28. Set the A/C button and fan control dial OFF, then
turn the ignition switch to LOCK (0).
29. Disconnect the jumper wire.
30. Remove the fan control relay from the under-hood fuse/relay box, and test it (see page 22-70).
Go to step 31.
Replace the fan control relay.
31. Turn the ignition switch to ON (II), then set the A/C button and fan control dial ON.
32. Measure the voltage between the fan control relay 5P socket terminal No. 1 and body ground.
Go to step 33.
Repair open in the wire between the radiator
fan and the fan control relay.
33. Set the A/C button and fan control dial OFF, then turn the ignition switch to LOCK (0).
Wire side of female terminals
Wire side of female terminals
Is there battery voltage?
Does t he r ad i at or f an r un? Is the relay OK ?
Is there battery voltage?
08/08/21 14:42:26 61SNR030_210_0059
ProCarManuals.com
DYNOMITE -2009-






µ
µ
µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
YES
NO
21-59
FAN CONTROL RELAY 5P SOCKET
BLUBLU
A/C CONDENSER FAN 2P CONNECTOR
BLK
A/C CONDENSER FAN 2P CONNECTOR
A/C DIODE A
1 2
1 2
A/C DIODE A 2P SOCKET BRN
34. Disconnect the A/C condenser fan 2P connector.
35. Check for continuity between the fan control relay5P socket terminal No. 4 and the A/C condenser fan
2P connector terminal No. 2.
Go to step 36.
Repair open in the wire between the fan
control relay and the A/C condenser fan.
36. Check for continuity between the A/C condenser fan 2P connector terminal No. 1 and body ground.
Replace the A/C condenser fan motor.
Check for an open in the wire between the A/C
condenser fan and body ground. If the wire is OK,
check for poor ground at G301 (see page 22-64). 37. Turn the ignition switch to LOCK (0).
38. Remove A/C diode A from the under-hood fuse/
relay box.
39. Using the diode setting ( ) on a DVOM, check for current flow in both directions between the A/C
diode A terminals No. 1 and No. 2.
Go to step 40.
Replace A/C diode A.
40. Turn the ignition switch to ON (II).
41. Measure the voltage between the A/C diode A 2P socket terminal No. 2 and body ground.
Replace the under-hood fuse/relay box
(see page 22-65).
Repair open in the wire between the No. 36
(10 A) fuse in the under-dash fuse/relay box and
A/C diode A.
Wire side of female terminals
Wire side of female terminals
Is there continuity?
Is there continuity? I s t her e cur r ent f l ow i n onl y one d i r ect i on?
Is there battery voltage?
08/08/21 14:42:27 61SNR030_210_0060
ProCarManuals.com
DYNOMITE -2009-



µ
µ µ
µ
µ
µ
YES
NO
YES
NO
YES
NO
21-61
ECM/PCM CONNECTOR A (44P)
GRY
JUMPER WIRE A/C DIODE B 2P SOCKET
A/C DIODE B
1 2
1 2
8. Turn the ignition switch to LOCK (0).
9. Reinstall the A/C condenser fan relay.
10. Jump the SCS line with the HDS. NOTE: This step must be done to protect the engine
control module (ECM)/powertrain control module
(PCM) from damage.
11. Disconnect ECM/PCM connector A (44P).
12. Connect the ECM/PCM connector A (44P) terminal No. 5 to body ground with a jumper wire.
13. Turn the ignition switch to ON (II). Check for loose wires or poor connections at
ECM/PCM connector A (44P) terminal No. 5. If the
connections are good, substitute a known-good
ECM/PCM, and recheck. If the symptom/indication
goes away, replace the original ECM/PCM
(see page 11-228).
Repair open in the wire between the A/C
condenser fan relay and the ECM/PCM. 14. Remove the A/C diode B from the under-hood fuse/
relay box.
15. Turn the ignition switch to ON (II).
16. Measure the voltage between the A/C diode B 2P socket terminal No. 2 and body ground.
Go to step 17.
Replace the under-hood fuse/relay box
(see page 22-65).
17. Using the diode setting ( ) on a DVOM, check for current flow in both directions between the A/C
diode B terminals No. 1 and No. 2.
Replace the under-hood fuse/relay box
(see page 22-65).
Replace the A/C diode B.
Terminal side of female terminals
Does t he A/ C cond enser f an r un on hi gh? Is there battery voltage?
I s t her e cur r ent f l ow i n onl y one d i r ect i on?
08/08/21 14:43:32 61SNR030_210_0062
ProCarManuals.com
DYNOMITE -2009-