ignition ACURA CSX 2006 Service Repair Manual

(#' 
')
µ
µ µ
µ
YES
NO YES
NO
DTC 86-FF:
19-8719-87
10. Reconnect all connectors.
11. Update the ECM/PCM if it does not have the latest
software (see page 11-227), or substitute a known-
good ECM/PCM (see page 11-7).
12. Clear the DTC with the HDS.
13. Test-drive the vehicle at 10 km/h (7 mph) or more.
NOTE: Drive the vehicle on the road, not on a lift.
14. Check for DTCs with the HDS.
Replace the ABS modulator-control unit
(see page 19-90).
If the ECM/PCM was updated, troubleshooting
is complete. If the ECM/PCM was substituted,
replace the original ECM/PCM (see page 11-228). 1. Turn the ignition switch to ON (II).
2. Clear the DTC with the HDS.
3. Turn the ignition switch to LOCK (0), then turn it to
ON (II) again.
4. Check for DTCs with the HDS.
Replace the ABS modulator-control unit
(see page 19-90).
Intermittent failure, the system is OK at this
time.F-CAN Communication with ABS
Malfunction
Is DT C 86-24 and/ or 86-25 indicated? Is DTC 86-FF indicated?
08/08/21 15:03:17 61SNR030_190_0087
ProCarManuals.com
DYNOMITE -2009-

Î
Î
(#'
)
µ
µ
µ
µ µ
µ
µ
µ
ABS indicator and brake system indicator do
not go off
YES
NO
YES
NO YES
NO
YES
NO
19-88ABS Components
Symptom Troubleshooting
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
IG1 (YEL)*
*1: ’06 model
*2: ’07 model (GRY)*
ABS MODULATOR-CONTROL UNIT 25P CONNECTOR
IG1 (YEL)*
*1: ’06 model
*2: ’07 model (GRY)*
1
2
12
1. Turn the ignition switch to LOCK (0).
2. Check the No. 4 (7.5 A) fuse in the under-dash fuse/ relay box.
Go to step 3.
Reinstall the checked fuse, then go to step 8.
3. Disconnect the ABS modulator-control unit 25P connector (see step 2 on page 19-90).
4. Check for continuity between ABS modulator- control unit 25P connector terminal No. 16 and
body ground.
Repair short to body ground in the wire
between the No. 4 (7.5 A) fuse in the under-dash
fuse/relay box and the ABS modulator-control
unit.
Install a new No. 4 (7.5 A) fuse in the under-
dashfuse/relaybox,thengotostep5. 5. Reconnect the ABS modulator-control unit 25P
connector.
6. Turn the ignition switch to ON (II).
7. Check the ABS indicator and the brake system indicator for several sec onds when the ignition
switch is tuned to ON (II).
Troubleshooting is complete.
Replace the ABS modulator-control unit
(see page 19-90).
8. Disconnect the ABS modulator-control unit 25P connector (see step 2 on page 19-90).
9. Turn the ignition switch to ON (II).
10. Measure the voltage between ABS modulator- control unit 25P connector terminal No. 16 and
body ground.
Go to step 11.
Repair open in the wire between the No. 4
(7.5 A) fuse in the under-dash fuse/relay box and
the ABS modulator-control unit.
11. Turn the ignition switch to LOCK (0).
Wire side of female terminals
Wire side of female terminals
Isthefuseblown?
Is there continuity? Does t he i nd i cat or s come on t hen go of f ?
Is there battery voltage?
08/08/21 15:03:17 61SNR030_190_0088
ProCarManuals.com
DYNOMITE -2009-


(#'

 )

Removal
19-90ABS Components
ABS Modulator-Control Unit Removal and Installation
A
B C
15 N·m
(1.5 kgf·m, 11 lbf·ft)
D
E
I F
G
H 15 N·m
(1.5 kgf·m, 11 lbf·ft)
9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft) 9.8 N·m
(1.0 kgf·m, 7.2 lbf·ft)
NOTE:
 Do not spill brake fluid on the vehicle; it may damage the paint; if brake fluid gets on the paint, wash it off immediately with water.
 Be careful not to damage or deform the brake lines during removal and installation.
 Plug the ends of the hoses and the joints to prevent spilling brake fluid.
1. Turn the ignition switch to LOCK (0).
2. Disconnect the ABS modulator-control unit 25P connector (A) by pu lling up the lock (B); the connector disconnects
itself.
3. Disconnect the six brake lines from the ABS modulator-control unit. NOTE: Brake lines are connected to the master cylinder (C) and to the right-front (D), the left-rear (E), the right-rear
(F), and the left-front (G) brake systems.
4. Remove the ABS modulator-control unit (H) with the brackets (I) from the body.
5. Remove the ABS modulator-control unit from the brackets.
6. Separate the bracket if necessary.
08/08/21 15:03:18 61SNR030_190_0090
ProCarManuals.com
DYNOMITE -2009-


(#'

 )
 Special Tools Required
Front
19-92ABS Components
Wheel Speed Sensor Replacement
A
B
C9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft)
Guide pin tool 07AAG-SVBA100
1. Turn the ignition switch to LOCK (0).
2. Release the connector clamp (A), then disconnect the wheel speed sensor connector (B).
3. Remove the clips, the bolt, and the wheel speed sensor (C).
4. Install the wheel speed sensor in the reverse order of removal, and note these items:  Install the sensor carefully to avoid twisting the wires.
 If the wheel speed sensor comes in contact with the wheel bearing, it is faulty. Investigate the cause beforereplacing the sensor.
5. Start the engine, and make sure the ABS indicator goes off.
6. Test-drive the vehicle, and make sure the ABS indicator does not come on.
08/08/21 15:04:46 61SNR030_190_0092
ProCarManuals.com
DYNOMITE -2009-

Î
Rear
19-93
Right side
9.8 N·m
(1.0 kgf·m,
7.2 lbf·ft) A
B
C
1. Turn the ignition switch to LOCK (0).
2. Release the connector clamp (A), then disconnect the wheel speed sensor connector (B).
3. Remove the clips, the bolt, and the wheel speed sensor (C). (cont’d)
08/08/21 15:04:46 61SNR030_190_0093
ProCarManuals.com
DYNOMITE -2009-


(#'
)
System IndicatorABS Indicator
Brake System Indicator
VSA Indicator
VSA Activation Indicator
19-97
General Troubleshooting Information
A
D B
C
This system has four indicators:
 ABS indicator (A)
 Brake system indicator (B)
 VSA indicator (C)
 VSA activation indicator (D)
When the system is OK, each indicator comes on for
about 2 seconds after turning the ignition switch to
ON (II), then goes off.
When the system detects a problem, a DTC is set and,
depending upon the failure, the VSA modulator-control
unit determines which indicator(s) are turned on. If the
problem goes away (system returns to normal), the
indicator(s) are controlled in the following way
depending upon the DTC that is set:  The indicator(s) come on and stay on when the ignition switch is ON (II).
 The indicator(s) automatically go off.
 The indicator(s) go off after the vehicle is driven. The ABS indicator comes on when the ABS function is
lost. The brakes still work like a conventional system.
The brake system indicator comes on when the EBD
function is lost, the parking brake is applied, and/or the
brake fluid level is low.
NOTE: If two or more wheel speed sensors fail, the
brake system indicator comes on.
The VSA indicator comes on when the VSA function is
lost.
The VSA activation indicator blinks when the VSA
function is activating. The VSA activation indicator
comes on and stays on when the VSA is turned OFF by
using the VSA OFF switch, or when the VSA function is
lost.
(cont’d)
08/08/21 15:04:50 61SNR030_190_0097
ProCarManuals.com
DYNOMITE -2009-

Diagnostic Trouble Code (DTC)
Self-diagnosis
Kickback
Pump Motor
Brake Fluid Replacement/Air BleedingHow to Troubleshoot DTCs
Intermittent Failures
19-98
VSA System Components
General Troubleshooting Information (cont’d)
 The memory holds all DTCs. However, when the
same DTC is detected more than once, the more
recent DTC is written over the earlier one. Therefore,
when the same problem is detected repeatedly, it is
memorized as a single DTC.
 The DTCs are indicated in the order they occur.
 The DTCs are memorized in the EEPROM. Therefore, the memorized DTCs cannot be erased by
disconnecting the battery. Do the specified
procedures to clear the DTCs.
 Self-diagnosis can be classified into two categories: – Initial diagnosis: Done right after the ignition switch is turned to ON (II) and until the ABS and VSA
indicators go off.
– Regular diagnosis: Done right after the initial diagnosis until the ignition switch is turned to
LOCK (0).
 When the system detects a problem, the VSA modulator-control unit shifts to fail-safe mode.
The pump motor operates when the VSA modulator-
control unit is functioning, and the fluid in the reservoir
is forced out to the master cylinder, causing kickback at
the brake pedal.  The pump motor operates when the VSA modulator- control unit is functioning.
 The VSA modulator-control unit checks the pump motor operation one time after completing initial
diagnosis during regular diagnosis when the vehicle
is driven over 15 km/h (10 mph).
Brake fluid replacement and air bleeding procedures
are identical to the procedures used on vehicles without
the VSA system (see page 19-9). The troubleshooting procedures assume that the cause
of the problem is still present, and the ABS and/or VSA
indicator is still on. Following a troubleshooting
procedure for a code that has been cleared but does not
reset can result in incorrect diagnosis.
1. Question the client about the conditions when the problem occurred, and try to reproduce the same
conditions for troubleshooting. Find out when the
ABS and/or VSA indicator came on, such as during
activation, after activation, when the vehicle was
traveling at a certain speed, etc. If necessary, have
the client demonstrate the concern.
2. When the ABS or VSA indicator does not come on during the test-drive, check for loose connectors,
poor contact of the terminals, etc. in the circuit
indicated by the DTC before you start
troubleshooting.
3. After troubleshooting, or the repairs are done, clear the DTCs, and test-drive the vehicle under the same
conditions that originally set the DTCs. Make sure
the ABS and VSA indicators do not come on.
4. Check for DTCs from other systems which are connected via F-CAN. If there are DTCs that are
related to F-CAN, one possible cause was that the
ignition switch was turned to ON (II) with the VSA
modulator-control unit connector disconnected.
Clear the DTCs. Check for fuel and emissions DTC’s
first.
NOTE: Always troubleshoot fuel and emissions
DTC’s first.
The term ‘‘intermittent failure’’ means a system may
have had a failure, but it checks OK now. If you cannot
reproduce the condition, check for loose connectors or
terminal pins related to the circuit that you are
troubleshooting.
08/08/21 15:04:50 61SNR030_190_0098
ProCarManuals.com
DYNOMITE -2009-


How to Use the HDS (Honda Diagnostic
System)How to Retrieve DTCs
How to Clear DTCs
19-99
A
1. If the system indicators stay on, connect the HDS to
the data link connector (DLC) (A) located under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t,
troubleshoot the DLC circuit (see page 11- 204).
4. Check the diagnostic trouble code (DTC) for all systems, troubleshoot the powertrain DTCs first
and note it. Then refer to the indicated DTC’s
troubleshooting, and do the appropriate
troubleshooting procedure.
NOTE: The HDS communication stops when the vehicle speed is at 50 km/h (31 mph) or more.
 The HDS reads the DTC, current data, and other system data.
 For specific operations, refer to the Help menu that came with the HDS. 1. With the ignition switch in LOCK (0), connect the
HDS to the data link connector (DLC) under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t
troubleshoot the DLC circuit (see page 11-204).
4. Follow the prompts on the HDS to display the DTC(s) on the screen. After determining the DTC,
refer to the DTC troubleshooting. Do the all
systems DTC check, and troubleshoot any
powertrain DTCs first.
5. Turn the ignition switch to LOCK (0).
1. With the ignition switch in LOCK (0), connect the HDS to the data link connector (DLC) under the
driver’s side of the dashboard.
2. Turn the ignition switch to ON (II).
3. Make sure the HDS communicates with the vehicle and the VSA modulator-control unit. If it doesn’t
troubleshoot the DLC circuit (see page 11-204).
4. Clear the DTC(s) by following the screen prompts on the HDS.
5. Turn the ignition switch to LOCK (0).
08/08/21 15:04:51 61SNR030_190_0099
ProCarManuals.com
DYNOMITE -2009-

•••
•••
´
´
´

(#'
)
VSA Modulator-Control Unit Inputs and Outputs for 37P Connector (Connector Disconnected)
TerminalnumberWire color Terminal sign Description Signal
19-106VSA System Components
System Description
NOTE: Standard battery voltage is about 12 V.
1 RED CAN-L F-CAN communication circuit
3 BLU STR-D Detects steering angle sensor signal
6 PNK FR-GND Detects right-front wheel speed sensor signal
7 ORN SVCC Power source for the steering angle sensor With ignition switch ON (II): about 5.0 V
8 PUR RL-GND Detects left-rear wheel speed sensor signal
9 LT GRN RR B Detects right-rear wheel speed sensor signal
10 BRN SGND Ground for the steering angle sensor
11 RED FL-GND Detects left-front wheel speed sensor signal
13 WHT FSR B Power source for the fail-safe relay Battery voltage at all times
14 RED MR B Power source for the motor relay Battery voltage at all times
Wire side of female terminals
08/08/21 15:04:53 61SNR030_190_0106
ProCarManuals.com
DYNOMITE -2009-

•••
´
´
´
•••
TerminalnumberWire color Terminal sign Description Signal
19-107
NOTE: Standard battery voltage is about 12 V.
15 WHT CAN-H F-CAN communication circuit
17 PUR STR-B Detects steering angle sensor signal
19 GRN FR B Detects right-front wheel speed sensor signal
20 YEL RL B Detects left-rear wheel speed sensor signal
21 BLU RR-GND Detects right-rear wheel speed sensor signal
22 WHT FL B Detects left-front wheel speed sensor signal
26 LT BLU K-LINE Communication with HDS
28 GRY IG1 Power source for activating the system With ignition switch ON (II): about battery
voltage
34 GRN STR-A Detects steering angle sensor signal
36 BLK GND Ground for the VSA modulator- control unit Continuity to ground
37 BLK MR-GND Ground for the pump motor Continuity to ground
(cont’d)
08/08/21 15:04:53 61SNR030_190_0107
ProCarManuals.com
DYNOMITE -2009-