dashboard ACURA CSX 2006 Service Workshop Manual






20-71
A
B
A
B C
D
B
C
D A
B C
D E
F
A
D
EA
C
Fastener Locations
:Clip,2
E
(Black)
7. Before installing the A-pillar trim (A), whether it is
being replaced or reinstalled, temporarily remove
the new upper clip (B).
8. Check the overlap between the headliner and A-pillar trim, and if necessary, adjust it (see page
24-185).
9. Carefully install a new upper clip (A) to the A-pillar trim (B). Be sure that the grommet (C) is nearest to
the top of the pin (D) as shown. 10. Reinstall the A-pillar trim (A).
–1 Insert the bottom of the trim into thedashboard (B).
–2 Place the trim over the A-pillar (C), and fit its upper clip (D), and lower clips (E) into the holes
(F) in the A-pillar, then lightly push the trim into
place.
NOTE: Make sure the side curtain airbag is not tucked down under the clips and the ribs.
 Push lightly on the upper clip. If you push too hard, the clip will be damaged, and it will not
hold the trim properly.
11. Reinstall the front door opening seal.
08/08/21 15:01:32 61SNR030_200_0073
ProCarManuals.com
DYNOMITE -2009-




20-85
A
B
B
A
B D
B
5x0.8mm
5N·m
(0.5 kgf·m,
4lbf·ft)
Fastener Locations
:Bolt,2
C
E
F
G A
B
C
A
Fastener Locations :Bolt,4
8x1.25mm
22 N·m
(2.2 kgf·m,
16 lbf·ft) A
6. Push the hook (A) with a flat-tip screwdriver
wrapped with protective tape, and turn the holder
(B) 90 °, then pull it out.
7. Remove the individual map light assembly (A). –1 Remove the lenses (B).
–2 Remove the bolts.
–3 If equipped, release the four tabs (C), then pullout the moonroof switch (D) or the navigation
microphone.
–4 Disconnect the front individual map light connector (E). If equipped, disconnect the
moonroof switch connector (F) and the
navigation microphone connector (G). 8. Without moonroof: Remove the driver’s dashboard
undercover (see page 20-104).
9. Detach the harness clips (A) from the A-pillar (B), and disconnect the roof wire harness connector (C).
10. Remove the center console (see page 20-92).
11. Slide both front seats all the way back, and recline the seat-backs fully.
12. Remove the bolts securing the parking brake base frame (A), and lay it down as needed.
(cont’d)
08/08/21 15:01:40 61SNR030_200_0087
ProCarManuals.com
DYNOMITE -2009-







(#'


 )
H

eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to damage, wrinkle, or twist the carpet.
 Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items:  Front seats, both sides (see page 20-118)
 Rear seat cushion (see page 20-133)
 Front door sill trim, both sides (see page 20-66)
 Rear door sill trim, both sides (see page 20-67)
 Kick panels, both sides (see step 5 on page 20-67)
 B-pillar lower trim (see page 20-72)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-







(#'


 )
H

eadliner
Grab handle
Sunvisor Special Tools Required
20-8820-88
Interior Trim
Headliner Removal/Installation
(cont’d)
Carpet Replacement
A
C
H
I
C
J K
B
B
F
D
E G
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Put on gloves to protect your hands.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to damage, wrinkle, or twist the carpet.
 Be careful not to damage the dashboard or other interior trim pieces.
1. Remove these items:  Front seats, both sides (see page 20-118)
 Rear seat cushion (see page 20-133)
 Front door sill trim, both sides (see page 20-66)
 Rear door sill trim, both sides (see page 20-67)
 Kick panels, both sides (see step 5 on page 20-67)
 B-pillar lower trim (see page 20-72)
 Driver’s dashboard undercover (see page 20- 103)
 Passenger’s dashboard undercover (see page 20-104)
 Center console (see page 20-92)
 Steering joint cover (see page 17-10)
08/08/21 15:01:42 61SNR030_200_0090
ProCarManuals.com
DYNOMITE -2009-


20-91
AB
C
C
10. Release the Velcro fastener (A), then pull the carpet (B) out from under the dashboard. 11. Pull the seat harnesses (C) out through the hole in
the carpet, then remove the carpet.
12. Install the carpet in the reverse order of removal, and note these items:
 Take care not to damage, wrinkle or twist the carpet.
 Make sure the seat harnesses and parking brake cables are routed correctly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the Velcro fasteners and the clips into place securely.
 Push the accelerator pedal hooks into place securely, and verify that the pedal is properly
fastened to the floor.
08/08/21 15:02:47 61SNR030_200_0093
ProCarManuals.com
DYNOMITE -2009-




(#'


 )
Special Tools Required
20-92 Consoles
Center Console Removal/Installation
A
B C F
astener Locations
:Clip,4
A
Fastener Locations :Clip,3
B : Clip, 2
C
C B
B
B
C A
KTC trim tool set SOJATP2014
SRS components are located in this area. Review the
S

RS component locations (see page 24-11) and the
precautions and procedures (see page 24-13) before
doing repairs or service.
NOTE:  Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
 Take care not to scratch the front seat, dashboard, and related parts.
1. Remove the passenger’s dashboard undercover (see page 20-104).
2. M/T model: Lower the shift lever boot (A) to release
the hooks (B) from the boot, then remove the shift
knob (C). 3.

Detach the clips by pulling the front inner panel (A)
up.
4. Gently pull out along the rear of the center console panel (A) to release the clips (B, C).
08/08/21 15:02:47 61SNR030_200_0094
ProCarManuals.com
DYNOMITE -2009-



20-94Consoles
Center Console Removal/Installation (cont’d)
A
B
C
B
A
B A
BC
8. Slide both front seats all the way back, and recline
the seat-back fully.
9. Slide the center console (A) rearward to release the pins (B) from the bracket (C).
10. Lift up the rear of the console (A), and remove it from the dashboard.
11. If equipped, disconnect the seat heater switch connectors (B). 12. Install the console in the reverse order of removal,
and note these items:
 Make sure each connector is plugged in properly.
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips and the hooks into place securely.
 When installing the center console panel, install the tabs (A) into the notch (B) of the parking brake
base frame (C).
08/08/21 15:02:48 61SNR030_200_0096
ProCarManuals.com
DYNOMITE -2009-

Î


(#'


")
S

pecial Tools Required
20-95
Center Console Disassembly/Reassembly
Fastener Locations
:TORXScrew,8
A A
BC
D
E F
G
H
I
I
A
A
B
C
D
KTC trim tool set SOJATP2014
NOTE: 
Use the appropriate tool from the KTC trim tool set to
avoid damage when removing components.
 Take care not to scratch the center console, the dashboard, and related parts.
1. Remove the center console (see page 20-92).
2. Remove the center console armrest (see page 20-96).
3. Remove the screws with a TORX T20 bit, and disconnect the console accessory power socket
connector (A). 4

. Release the hooks (A) and the pins (B), then
separate the left console side panel (C), the right
console side panel (D), the console beverage holder
(E) and the console box (F). If equipped, detach the
harness clips (G), then remove the console
subharness (H) from the hooks (I).
5. Release the hooks (A, B), then separate the console upper box (C) and the console lower box (D).
6. Assemble the console in the reverse order of disassembly, and make sure the console
subharness connector is plugged in properly.
08/08/21 15:02:49 61SNR030_200_0097
ProCarManuals.com
DYNOMITE -2009-




(#'
 )
S

pecial Tools Required
20-98 Dashboard
Instrument Panel Removal/Installation
Fastener Locations
:Screw,3 F
astener Locations
:Clip,2
A
Fastener Locations : Clip, 6
A
B C
KTC trim tool set SOJATP2014
NOTE:

Take care not to scratch the instrument panel and
related parts.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Remove these items:
 Subdisplay visor (see page 20-100)
 Navigation unit, with navigation system– ’06-08 models (see page 23-155)
– ’09 model (see page 23-355)
 Audio unit, without navigation system – ’06-08 models (see page 23-80)
– ’09 model (see page 23-256)
2. Remove the screws. 3

. Detach the clips along the lower edge of the
instrument panel (A).
4. Detach the clips along the upper edge of the instrument panel (A). Gently pull out the instrument
panel to release the hooks (B) from the holder (C) of
the gauge control module.
5. Install the instrument panel in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:02:52 61SNR030_200_0100
ProCarManuals.com
DYNOMITE -2009-



(#' )

S

pecial Tools Required
20-99
Gauge Control Module (Speedo) Trim Removal/Installation
Fastener Locations
:Clip,4
AA Fa

stener Locations
: Clip, 5
A A A
B
B
C
KTC trim tool set SOJATP2014
NOTE: 
Take care not to scratch the dashboard and related
parts.
 Use the appropriate tool from the KTC trim tool set to avoid damage when removing components.
1. Pry up on the inside edge of the gauge control module (speedo) trim (A) with a trim tool to detach
the clips. 2

. Detach the clips and release the hooks (A) with a
trim tool, and the pins (B) along the edge of the
gauge control module (speedo) trim (C), then
remove the trim.
3. Install the trim in the reverse order of removal, and note these items:
 If the clips are damaged or stress-whitened, replace them with new ones.
 Push the clips into place securely.
08/08/21 15:02:52 61SNR030_200_0101
ProCarManuals.com
DYNOMITE -2009-