width ACURA INTEGRA 1998 Service Repair Manual

ACURA INTEGRA 1998 Service Repair Manual INTEGRA 1998 ACURA ACURA https://www.carmanualsonline.info/img/32/56983/w960_56983-0.png ACURA INTEGRA 1998 Service Repair Manual

Page 90 of 1680

ACURA INTEGRA 1998  Service Repair Manual \
Valve Seats
Reconditioning
ACTUALSEATINGSURFACE
VALVESEAT
Renew the valve seats in the cylinder head using avalve seat cutter.
NOTE: lf guides are worn (see page 6-26), replace
them {see page 6-27)

Page 376 of 1680

ACURA INTEGRA 1998  Service Repair Manual 8.
9.
f;:Y:fffrf#:Juer Sl[
Measure the clearance between the reverse change
holder and the sth/reverse shift piece pin.
Standard:
Reverse Side: 0.05 - 0.45 mm (0.002 - 0.018 inl
5th Side: 0.4 - 0.9

Page 377 of 1680

ACURA INTEGRA 1998  Service Repair Manual Reverse Change Holder,
Clearance Inspection {contdl
Reverseldler Gear
Removal
1. Remove the reverse change holder.
2. Remove the reverse idler gear and the reverse idler
oear shaft.
\
i1
\
Measure th

Page 378 of 1680

ACURA INTEGRA 1998  Service Repair Manual Change Holder Assembly
Clearance Inspection
Measure the clearance betwe€n the shift Diece and
the shift arm holder.
Standard: 0.1 - 0.3 mm (0.004 - 0.012 inl
Servico Limit: 0.6 mm (0,02 inl
lf the c

Page 380 of 1680

ACURA INTEGRA 1998  Service Repair Manual 9.Measure the clearance between the select arm
the change piece.
Standard: 0.05 - 0.35 mm {0.002 - 0.014 in)
Service Limit: 0.5 mm {0.02 inl
Removal
Remove the shift piece shaft, then remove the shift

Page 385 of 1680

ACURA INTEGRA 1998  Service Repair Manual Shift Fork Assembly
Clearance Inspection
NOTE: The synchro sleeve and the synchro hub shouldh6 ronlr.o.l ,.. car
Measure the clearance between each shift fork and
its matching synchro sleeve.
Standard

Page 556 of 1680

ACURA INTEGRA 1998  Service Repair Manual Countershaft
Inspection (contd)
5. lf the clearance is out of tolerance. remove the
28 mm distance collar and measure the width.
6. Select and install a new distance collar. then
recheck.
DISTANCE CO

Page 888 of 1680

ACURA INTEGRA 1998  Service Repair Manual Ouarter Glass
Installation (contd)
lf the old quarter glass is to be reinstalled land
either of the clips are broken off the molding), apply
a light coat ot primer (C 100, or equivalent|, then
apply

Page 1643 of 1680

ACURA INTEGRA 1998  Service Repair Manual I
I
Standards and Service Limits
Cylinder Head/Valve Train (B18Bl engine)Section 6
*: Measured between the camshaft and rocker arm.
NH: NIHON HATSUJO manufactured valve spring
CH: CHUO HATSUJO manufac

Page 1644 of 1680

ACURA INTEGRA 1998  Service Repair Manual Engine Block (81881 engine)Section 7Unit of length: mm (in)
3-3
\
Yl
R: RIKEN manufactured piston ringT: TEIKOKU PISTON RING manufactured piston ring
E - Declror
MEASUREMENTSTANDARD (NEW}SERVICE LIMI
Page:   1-10 11-20 next >