engine Acura MDX 2003 Owner's Manua

µµ
µ
µµ
To shif t to Reverse
f rom Park, see the explanation under
Park. To shif t to Reverse f rom
Neutral, come to a complete stop and
then shift. Use Neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to Park posi-
tion if you need to leave the vehicle
f or any reason. Press on the brake pe-
dal when you are moving the shif t
lever from Neutral to another gear.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear for your speed and
acceleration. You may notice the
transmission shif ting up at higher
speeds when the engine is cold. This
helps the engine warm up f aster.
Your car has a reverse lockout so
you cannot accidentally shif t to
Reverse from Neutral or any other
driving position when the vehicle
speed exceeds 7 9 mph (12 14
km/h).
If you cannot shif t to Reverse when
the car is stopped, press the brake
pedal and slowly shif t to Neutral, and
then to Reverse.
If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to Reverse. (Ref er
to Shif t Lock Release on page ).
257
Reverse (R) Neutral (N)
Drive (D )
5
Automatic Transmission
Driving255

µµ
These positions
are similar to D , except when you
select the D position, only the f irst
f our gears are selected. When you
select D , only the f irst three gears
are selected. D can also keep the
transmission f rom cycling between
f ourth and f if th gears in stop-and-go
driving, and D can keep the
transmission f rom cycling between
third and f ourth gears. This position locks
the transmission in second gear. It
does not downshif t to f irst gear
when you come to a stop. Second
gives you more power when climbing,
and increased engine braking when
going down steep hills. Use second
gear when starting out on a slippery
surf ace or in deep snow. It will help
reduce wheelspin.
ForfasteraccelerationwheninD ,
D or D , you can get the
transmission to automatically
downshif t by pushing the accelerator
pedal to the f loor. The transmission
will shif t down one or two gears,
depending on your speed.
Use D to provide engine braking
when going down a steep hill. D
gives you more power and increased
engine braking.
5
4
3 4
3 3
45
3 3
Drive(D,D) Second(2)43
Automatic Transmission
Driving256

µIf you exceed the maximum speed
f or the gear you are in, the engine
speed will enter into the tachometer’s
red zone. If this occurs, you may f eel
the engine cut in and out. This is
caused by a limiter in the engine’s
computer controls. The engine will
run normally when you reduce the
RPM below the red zone. Set the Parking brake.
With the lever in this
position, the transmission locks in
First gear.
If you shif t into First position when
the vehicle speed is above 31 mph
(50 km/h), the transmission shif ts
into Second gear f irst to avoid
sudden engine braking. This allows you to move the shif t
lever out of Park if the normal
method of pushing on the brake
pedal does not work. This procedure
is also used to release the Reverse
Lockout.
Make sure the key is in the
ignition switch LOCK (0) position.
To release the Reverse Lockout,
make sure the key is in the
ACCESSORY (I) position.
1.
2.
CONT INUED
Engine Speed Limiter
Shift Lock Release
First (1)
Automatic Transmission
Driving257

Put a cloth on the edge of the Shif t
Lock Release slot cover next to
theshiftlever.Useasmallflat-
tipped screwdriver or small metal
plate (neither are included in the
tool kit) to remove the cover.
Caref ully pry on the edge of the
cover.Insert a screwdriver in the Shif t
Lock Release slot.
Push down on the screwdriver
while you press the release button
and move the shif t lever out of
Park to Neutral.
To release the Reverse Lockout,
move the shift lever from Neutral
to Reverse, then to Park.Remove the screwdriver f rom the
shif t lock release slot, then install
anewcover.
Depress the brake pedal and
restart the engine.
If you need to use the Shif t Lock
Release, it means your vehicle is
developing a problem. Have the
vehicle checked by your Acura
dealer.
3. 4.
5.6.
Automatic Transmission
Driving258
COVER
SHIFT LOCK RELEASE SLOT

The Variable Torque Management
4WD System (VTM-4) automatically
transf ers varying amounts of engine
torque to the rear wheels.If more traction is needed when your
MDX is stuck or is likely to become
stuck, you can use the VTM-4 Lock
button to increase torque to the rear
wheels when the shif t lever is in the
1, 2 or R position. As soon as this
f eature is no longer needed, press
the VTM-4 Lock button again to
disengage the VTM-4 Lock.
Variable Torque Management 4WD System
Driving
VTM-4 Lock
259
Do not use the VTM-4 Lock button on
dry, paved roads. Driving on dry,
paved roads with VTM-4 Lock ON may
damage the rear dif f erential when
making a turn. Strange noises and
vibration can also result.

When the brake pads need replacing,
you will hear a distinctive metallic
‘‘screeching’’ sound when you apply
the brakes. If you do not have the
brake pads replaced, they will begin
screeching all the time.
Constant application of the brakes
when going down a long hill builds
up heat and reduces their ef f ective-
ness. Use the engine to assist the
brakes by downshif ting to a lower
gear and taking your f oot of f the
accelerator pedal.
Check your brakes af ter driving
through deep water. Apply the
brakes moderately to see if they f eel
normal. If not, apply them gently and
f requently until they do. Since a
longer distance is needed to stop
with wet brakes, be extra cautious
and alert in your driving.
Your Acura is equipped with disc
brakes at all f our wheels. A power
assist helps reduce the ef f ort needed
on the brake pedal. The ABS helps
you retain steering control when
braking very hard.
Put your f oot on the brake pedal only
when you intend to brake. Resting
your f oot on the pedal keeps the
brakes applied lightly, causing them
to build up heat. Heat build-up can
reduce how well your brakes work. It
also keeps your brake lights on all
the time, conf using drivers behind
you.
All f our brakes have audible brake
wear indicators.
Your brakes may sometimes squeal
or squeak when you apply them
lightly. Do not conf use this with the
brake wear indicators. The
indicators make a very audible
‘‘screeching.’’ Brake Wear Indicators
The Braking System
Driving262

The VSA system cannot enhance the
vehicle’s driving stability in all
situations and does not control your
vehicle’s entire braking system. It is
still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.When VSA activates, you will see the
VSA Activation indicator blink.
The Vehicle Stability Assist system
helps to stabilize the vehicle during
cornering if the vehicle turns more
or less than desired. It also assists
you in maintaining traction while
accelerating on loose or slippery
road surf aces. It does this by
regulating the engine’s output, and
by selectively applying braking.
When VSA activates, you may notice
that the engine does not respond to
the accelerator in the same way it
does at other times. You will also see
the VSA Activation Indicator blink.
Driving
Vehicle Stability Assist (VSA) System
VSA A ct ivat ion Indicat or
266
VSA ACTIVATION INDICATOR

The VSA system indicator (see page) comes on and stays on when
there is a problem with the VSA
system. The VSA Activation
indicator will also come on. If the VSA indicator comes on while
driving, pull to the side of the road
when it is saf e and turn of f the
engine. Reset the system by
restarting the engine, and watch the
VSA system indicator. If the
indicator remains on, or comes back
on while driving, have the VSA
system inspected by your Acura
dealer.
If the indicator does not come on
when the ignition switch is turned
ON(II),theremaybeaproblem
with the VSA system. Have your
dealer inspect your vehicle as soon
as possible.
Without VSA, your vehicle will have
normal braking and cornering ability,
but it will not have VSA traction and
stability enhancement.
This switch is under the lef t vent.
Press it to turn the Vehicle Stability
Assist system on and of f .
When VSA is off, the VSA Activation
Indicator light comes on as a
reminder. Pressing the switch again
turns the system back on.
73
CONT INUED
Vehicle Stability Assist (VSA) System
Driving
VSA Syst em Indicat orVSA Of f Switch
267
VSA SYSTEM INDICATOR

VSA is turned on every time you
start the engine, even if you turned it
off the last time you drove the
vehicle.Driving with varying tire or wheel
sizes may cause the VSA to
malf unction. When replacing tires,
make sure they are of the same size
and type as your original tires (see
page ).
Deactivate the VSA system if you
need to drive with the compact spare
tire installed (see page ).
If you install winter tires, make sure
they are the same size as those that
were originally supplied with your
car. Exercise the same caution
during winter driving as you would if
your vehicle was not equipped with
VSA.337
360
Vehicle Stability Assist (VSA) System
Driving
VSA and Tire Sizes
268

When climbing hills, closely watch
your temperature gauge. If it nears
the red (Hot) mark, turn the air
conditioning of f , reduce speed and, if
necessary, pull to the side of the
road to let the engine cool.
If the transmission shif ts f requently
while going up a hill, shif t down one
gear.
If you must stop when f acing uphill,
use the f oot brake or parking brake.
Do not try to hold the vehicle in
placebypressingontheaccelerator,
as this can cause the automatic
transmission to overheat.
When driving down hills, reduce
your speed and shif t down to D . Do
not ‘‘ride’’ the brakes, and remember
it will take longer to slow down and
stop when towing a trailer.Crosswinds and air turbulence
caused by passing trucks can disrupt
your steering and cause your trailer
to sway. When being passed by a
truck or other large vehicle, keep a
constant speed and steer straight
ahead. Do not try to make quick
steering or braking corrections.
Always drive slowly and have
someone guide you when backing up.
Grip the of the steering
wheel; then turn the wheel to the lef t
to get the trailer to move to the lef t,
andturnthewheelrighttomovethe
trailer to the right.
Follow all normal precautions when
parking, including putting the
transmission in PARK and f irmly
setting the parking brake when you
have f inished parking.
Donotparkonaninclineunlessitis
unavoidable. If you must park on an
incline, turn the vehicle wheels
toward the curb on a downhill and
awayfromthecurbonanuphill.
After parking, place wheel chocks at
each trailer tire, on the downhill side.
If the vehicle wheels slip when
retrieving a boat f rom the water,
shifttofirstgearandturnonVTM-4
Lock (see page ).
Disengage VTM-4 Lock as soon as
the boat is out of the water to
prevent damage to the VTM-4
system.
259
3
bottom
Driving on Hills
Handling Crosswinds and
T urbulence
Backing Up Parking
Ret rieving a Boat
Towing a Trailer
Driving282