lock Acura MDX 2005 Service Manual

Clock
Direction of travel
Outside temperature
Instantaneous f uel mileageTheAvgdisplayshowsyouthe
average f uel economy since you
last reset the display.
The E/T is the elapsed time that
the ignition has been on. It
automatically resets to 0.0 when it
reaches twelve hours. This display
can be reset at any time.
The display also has manual
f unctions f or the Climate Control
System. Ref er to page .
All models of MDX have a trip
computer. To operate the trip
computer on models with the
navigation system, ref er to the
navigation manual.
The Trip Computer displays the
f ollowing inf ormation.
The temperature sensor is located
in the f ront bumper, and can be
affected by heat from the road
surf ace, engine heat, and the
exhaust f rom the surrounding
traf f ic. Because of these
conditions, it may take a while f or
the temperature to read correctly. The Range, or estimated distance
you can travel on the fuel
remaining in the tank estimated
f rom the f uel economy you have
gotten over the last several miles
(kilometers).
The Trip display shows you the
total distance you have driven
since it was last reset.
Press the TRIP button to show either
the range and Avg f uel economy, or
the E/T and Trip odometer.
To reset the Avg f uel economy, E/T,
and Trip odometer, press and hold
the RESET button until you hear a
beep.
The outside temperature, f uel
economy, range, and trip odometer
can be displayed in either English or
Metric units. To change between
units, press the TRIP button and
hold it f or f ive seconds.
106
(Without Navigation System)
Changing and Resetting the
Display
Changing Units of Measurement
Trip Computer
150

To set the clock:Push the CLOCK button. The
hours digits will start blinking. If
you want to only set the minutes,
go to step 4. To change the hours to a lower
number, press and hold the
MODE button. To change the
hours to a higher number, press
andholdtheA/Cbutton.
When the hours reach the desired
number, release the button.
To set the minutes, press the
CLOCK button again. The
minutes digits will start blinking.
Use the MODE or A/C button to
set the minutes to the desired
number.
Press the CLOCK button again.
The clock will return to its normal
display.
For example:
1:06 will reset to 1:00
1:52 will reset to 2:00 You can quickly set the time to the
nearest hour. Press the CLOCK
button, then press the RESET button.
If the displayed time is before the
half hour, it will reset back to the
previous hour. If the displayed time
is af ter the half hour, it will reset
f orward to the next hour.
1. 2.
3.
4.
5.
6.
Setting the Clock
Trip Computer
Features
151

µµµµ
µµ
The compass may need to be
manually calibrated af ter exposure to
a strong magnetic field. If the
compassseemstobecontinually
showing the wrong direction and is
not self -calibrating, do the f ollowing. You should do this procedure
in an open area, away from buildings,
power lines, and other vehicles. Press and hold the CLOCK and
TRIP buttons until the display
changes (about 1 second).
Press the Calibrate (MODE)
button.
Press the Set (FAN) button.
‘‘Calibrate’’ will start blinking, and
the direction display will change to
‘‘ ’’.
Drive the vehicle slowly in two
complete circles.
When the display goes f rom
‘‘ ’’ to an actual heading, the
unit is calibrated.
Press the CLOCK, TRIP, or
RESET button to complete the
calibration and return the display
to normal.
Compass operation can be af f ected
by driving near power lines or
stations, across bridges, through
tunnels, over railroad crossings, past
large vehicles, or driving near large
objects that can cause a magnetic
disturbance. It can also be af f ected
by accessories such as antennas and
roof racks that are mounted by
magnets.
If you see ‘‘ ’’ in the direction
display and ‘‘Calibrate’’ is blinking,
the compass is self -calibrating.
1.
2.
3.4.
5.
6.
Compass Operation
Compass Calibration
Trip Computer
152
NOTE:

In most areas, there is a variation
between magnetic north and true
north. Zone selection is required so
the compass can compensate f or this
variation. To check and select the
zone set into the compass, do the
f ollowing.Press and hold the CLOCK and
TRIP buttons until the display
changes (about 1 second). Press the Zone (A/C) button. The
zone the compass is currently set
to is displayed.
Find the zone f or your area on the
map.If the zone is incorrect, press and
hold the MODE button to get the
number to count down, or the A/C
button to get the number to count
up. If the zone is correct, continue
to step 5.
Press the Set (FAN) button to set
the zone selection.
Press the CLOCK, TRIP or
RESET button to exit the zone
selection and return display to
normal.
1. 2.
3.4.
5.
6.
CONT INUED
Compass Zone Select ion
Trip Computer
Features
153

The Brightness control has seven
positions. In the middle f ive positions
the display will dim when you turn
on the parking lights or headlights.
Moving the control to the far left
position turns of f the display. It will
come back on f or several seconds if
you press any of the buttons.
In the f ar right (maximum
brightness) position, the display will
notdimwhenyouturnonthe
parking lights.
Always use a sof t cloth and mild
glass/plastic cleaner (such as
cleaners f or computer monitor
screens) to clean the display.Whenever you shif t to R (Reverse)
with the ignition switch in the ON
(II) position, the rear view is shown
on the navigation system screen.
For the best picture, always keep the
rear view camera clean, and do not
cover the camera lens.When in reverse, the touch screen,
and Navi ‘‘hard’’ buttons are locked
out, except the A/C-INFO button.
Touching the A/C-INFO button
allows you to adjust the brightness of
the rear view camera image. Touch
the A/C-INFO button again to leave
the brightness adjust mode.
The camera brightness
cannot be adjusted by voice control.
Since the rear view camera display
area is limited, you should always
back up slowly and caref ully, and
look behind you f or obstacles.
When you wipe the screen, some
black lines may appear because of
static electricity build-up. This is
normal. They will disappear in 5 to
10 minutes.Navigation models
BRIGHT NESS control
Cleaning the Display Rear View Camera and Monitor
Trip Computer, Rear View Camera and Monitor
Features
155
NOTE:
REAR VIEW CAMERA

Unplug the garage door opener
motor f rom the house current.Press and hold the remote control
button and one of the HomeLink
buttons at the same time.
Holdtheendof thegaragedoor
opener remote control 2 to 5
inches f rom HomeLink. Make
sure you are not blocking your
view of the red indicator in
HomeLink. The remote control
you are training f rom may stop
transmitting after 2 seconds. This is
not long enough f or HomeLink to
learn the code. Release and press the
button on the remote control every 2
seconds until HomeLink has learned
the code.
The red indicator in HomeLink
should begin f lashing. It will f lash
slowly at first, then rapidly.
When the red indicator f lashes
rapidly, release both buttons.
HomeLink should have learned
the code f rom the remote control. Plug in the garage door opener
motor, then test the HomeLink
button by pushing it. If the button
does not work, repeat the
procedure to train it again. If it still
does not work, you may have a
variable or rolling code garage
door opener. See if you do by
pressing and holding the
HomeLink button you just trained.
If the red indicator blinks for 2
seconds then stays on, you have a
rolling code garage door opener.
Go to ‘‘Training with a Rolling
Code System’’ (see page ).
Repeat these steps to train the
other two HomeLink buttons to
operate any other remotely
controlled devices around your
home (lighting, automatic gate,
security system, etc.).
2. 3.
4.
1.
5.6.
7.
158
Canadian Owners:
HomeL ink Universal T ransceiver
Features
157

Î
Î
µ
µ
Î
To skip a voice prompt, press the
Talk button while the HFL is
speaking. The HFL will then begin
listening f or your next command. To enter a string of numbers in a
Call or Dial command, you can say
them all at once, or you can
separate them in blocks of 3, 4, 7,
10, and 11. Many commands can be spoken
together. For example, you can
say, ‘‘Dial 123-456-7891.’’
All phones may not
operate identically, and some may
cause inconsistent operation of the
HFL.
Here are some guidelines f or using
voice control:
Signal Strength (models without
navigation system) Indicates
the network signal strength of the
current phone call. Five bars
equals f ull signal strength.
ROAM Status (models without
navigation system) Indicates
your phone is roaming.
Some phones will not send this
inf ormation to the HFL. TheHFLisoperatedbytheHFL
TALK/BACKbuttonontheleftside
of the steering wheel. The next f ew
pages provide easy-to-use
instructions f or all basic f eatures of
the HFL.
To enter a command, press the top
of the TALK/BACK button. Then,
af ter the beep, say your command
in a clear, natural tone.
If the HFL does not recognize a
command, its response is, ‘‘Pardon.’’
If it doesn’t recognize the command a second time, its
response is, ‘‘Please repeat.’’ If it
doesn’t recognize the command a
third time, it plays the Help
prompt.
To hear a list of available options
at any time, press the top of the
TALK/BACK button, wait f or the
beep, and say, ‘‘Hands f ree link
help.’’
For best system operation, set the
climate control f an speed to low,
and direct the center vents away
f rom the microphone in the ceiling.
:
How to Use the HFL
Using Voice Control
HandsFreeL ink
162
NOTE:
TM

To go back one step in a command
process, say, ‘‘Go back,’’ or press
the Back button.
If nothing is said while the HFL is
listening f or a command, the HFL
will time out and stop its voice
recognition. The next time you
press the top of the TALK/BACK
button, the HFL begins listening
f rom the point at which it timed
out.
When you f inish a command
sequence, the HFL goes back to
its main menu. For example, when
you store the name, ‘‘Eric,’’ the
HFL response is, ‘‘Eric has been
stored.’’ The next time you pressthe Talk button, you will be at the
main menu.
To end a command sequence at
any time, press and hold the Back
button, or press the Talk button,
wait f or the beep, and say, ‘‘Cancel.’’
ThenexttimeyoupresstheTalk
button, the HFL begins f rom its
main menu. The HFL will accept a numeric, f our-
digit passcode that you can use f or
security purposes.
With the ignition in the ON (II)
position, press and release the top
of the TALK/BACK button on the
steering wheel. Af ter the beep, say
‘‘Security.’’ The HFL response is
‘‘Security options are lock, unlock,
and set passcode.’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Set passcode.’’
The HFL response is ‘‘What is the
new f our-digit passcode?’’ (If you
are changing the passcode, you
will f irst be asked f or the current
passcode.)
Press and release the top of the
TALK/BACK button. After the beep, say the f our-digit passcode
you want to use. For example, say
‘‘1,2,3,4.’’TheHFLresponseis
‘‘1,2,3,4.Isthiscorrect?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Yes.’’ The HFL
response is ‘‘The new passcode
has been stored. Returning to the
main menu.’’
Once a passcode is set, you can lock
the HFL so it only operates after the
passcode is entered, or you can
unlock it so anyone using your
vehicle can also use the HFL. Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Security.’’ The HFL
response is ‘‘Security options are
lock, unlock, and set passcode.’’
2. 1.
4. 5.
3. 1.
To set your passcode, do this:
To lock or unlock the HFL, do this:
CONT INUED
HandsFreeL ink
Setting Your PasscodeL ocking or Unlocking the HFL
Features
163
TM

Thevoiceof theHFLcanbesetto
male or f emale (U.S. models only).
Also, the incoming notif ication can
be set to a ring tone, a prompt, or no
notification.
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Lock’’ or ‘‘Unlock.’’
Lock means the HFL will prompt
you f or your passcode each time
the ignition switch is turned to ON
(II) and you press the Talk button.
You will only be asked f or the
passcode once per ignition cycle. If
the HFL is locked, its response is
‘‘System is locked. Each time the
vehicle is turned on, the passcode
will be required to use the system.’’
If the HFL is unlocked, its
response is ‘‘The system is
unlocked. Returning to the main
menu.’’ Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘System.’’ The HFL
response is, ‘‘System options are
setup and clear.’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Setup.’’ The HFL
response is ‘‘Would you like male
or f emale prompts?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Male’’ or ‘‘Female,’’
depending on the system voice
you want. The HFL response is,
‘‘Male (Female) prompts have
been selected. Would you like an
audible notif ication of an incomingcall?’’
Press and release the top of the
TALK/BACK button. After the
beep, say ‘‘Ring tone’’ or ‘‘Prompt.’’
If you choose ‘‘Ring tone’’ you will
hear a ring tone through the audio
speakers to announce an incoming
call. If you choose ‘‘Prompt,’’ you
will hear this message to
announce an incoming call: ‘‘You
have an incoming call.’’ Press and release the top of the
TALK/BACK button. If you say
‘‘Yes’’ af ter the beep, the HFL
response is, ‘‘Would you like a ring
tone or a prompt?’’ If you say ‘‘No’’
af ter the beep, the HFL returns to
its main menu. Saying ‘‘No’’ will
result in no ring tone or prompt
playback during an incoming call.
The audio system will still mute,
and a message will be displayed.
2. 1. 4.
5.
3.
2.
To set up the system, do this:
Setting Up the System
HandsFreeL ink
164
TM

The OnStarsystem in your vehicle
gives you access to a wide range of
services and information with the
touch of a button. An OnStar advisor
is available 24 hours a day, 7 days a
week.
The Saf e and Sound Plan provides
these f eatures: Roadside Assistance
Emergency Services
Automatic Notif ication of Airbag
Deployment
Accident Assist
Remote Door Locking/Unlocking
Stolen Vehicle Tracking
Misplaced Vehicle Assistance
Online Concierge Services. The Directions and Connections
Plan provides these additional
f eatures:
Route Support
Ride Assist
Inf ormation and Convenience
Services
The Luxury and Leisure Plan adds
personal concierge services.
The OnStar buttons and indicator
are located on the ceiling near the
f ront map lights.
U.S. Touring model with NavigationSystemOnStar Control Panel
OnSt ar
Features
173
EMERGENCY BUTTON SYSTEM
STATUS
INDICATOR
CALL ANSWER/
CALL END BUTTON
OnStar
BUTTON
VOICE
ACTIVATED
KEYPAD