radio ACURA TL 1995 Service Owner's Manual

Airbag

Replacement

After a collision in which the airbags were deployed, the

airbag assemblies and the SRS unit must be replaced.

Store a removed airbag assembly with

the pad surface up. If the airbag is improperly stored

face down, accidental deployment could propel the unit

with enough force to cause serious injury.

CAUTION:

Always disconnect the airbag connectors when the

SRS main harness is disconnected.

'96 Model: Always keep the short connector (RED) on

the passenger's airbag when the harness is discon-

nected.

Do not disassemble or tamper with the airbag.

NOTE:

Do not install used SRS parts from another vehicle.

When repairing, use only new SRS parts.

Carefully inspect the airbag before you install it. Do

not install an airbag that shows signs of being

dropped or improperly handled, such as dents, cracks

or deformation.

1. Make sure you have the anti-theft code for the radio,

then write down the frequencies for the radio's pre-

set buttons.

2. Disconnect the battery negative cable, then discon-

nect the positive cable from the battery, and wait at

least three minutes.

3. Disconnect the airbag connectors:

Driver's Side:

Remove the access panel from the steering wheel,

then disconnect the 2P connector between the driver's

airbag and cable reel.

ACCESS

PANEL
Front Passenger's Side:

'96 Model:

Remove the glove box, then remove the short connec-

tor (RED) from it's holder.

Disconnect the 3P connector between the front pas-

senger's airbag and SRS main harness, then connect

the short connector (RED) to the airbag side of the con-

nector.

FRONT PASSENGER'S

AIRBAG

3P CONNECTOR
SHORT CONNECTOR (RED)

SRS MAIN HARNESS

'97 - 98 Models:

Remove the glove box.

Disconnect the 2P connector between the front pas-

senger's airbag and SRS main harness.

FRONT PASSENGER'S AIRBAG

2P CONNECTOR

SRS MAIN HARNESS

2P CONNECTOR

DRIVER'S AIRBAG

2P CONNECTOR
CABLE REEL

2P CONNECTOR
DRIVER'S

AIRBAG.ProCarManuals.com

6. Reconnect the airbag connectors.

Front Passenger's Side:

'96 Model:

Attach the short connector (RED) to the connector

holder, then reinstall the glove box.

SHORT CONNECTOR

(RED) /HOLDER

FRONT PASSENGER'S

AIRBAG

3P CONNECTOR
SRS MAIN HARNESS

3P CONNECTOR

'97-98 Models:

Attach the airbag connector to the connector holder,

then install the glove box.

SRS MAIN HARNESS

2P CONNECTOR

FRONT PASSENGER'S

AIRBAG

2P CONNECTOR
Driver's Side:

Connect the driver's airbag 2P connector to the cable

reel 2P connector, then install the access panel on the

steering wheel.

CABLE REEL

2P CONNECTOR

ACCESS PANEL

DRIVER'S AIRBAG

2P CONNECTOR

7. Connect the battery positive cable, then connect the

negative cable.

8. After installing the airbag, confirm proper system

operation:

Turn the ignition switch ON (II); the SRS indicator

light should come on for about six seconds and

then go off.

Make sure both horn buttons work.

Take a test-drive, and make sure the cruise con-

trol switches work.

9. Enter the anti-theft code for the radio, then enter the

customer's radio station presets.ProCarManuals.com

Airbag
Disposa l
Before scrappin g an y airbag s (includin g thos e in a whol e
vehicl e t o b e scrapped) , th e airbag s mus t b e deployed . I f
th e vehicl e i s stil l withi n th e warrant y period , befor e yo u
deplo y th e airbags , th e Acur a Distric t Technica l Manage r
must giv e approva l and/o r specia l instructions . Onl y afte r
th e airbag s hav e bee n deploye d (a s th e resul t o f vehicl e
collision , fo r example) , ca n the y b e scrapped . I f th e
airbag s appea r intac t (no t deployed) , trea t the m wit h
extrem e caution . Follo w thi s procedure :
Deployin g th e Airbags : In-vehicl e
NOTE : I f a n SR S vehicl e is t o b e entirel y scrapped , it s air -
bag s shoul d b e deploye d whil e stil l i n th e vehicle . Th e
airbag s shoul d no t b e considere d a s salvageabl e part s
an d shoul d neve r b e installe d in anothe r vehicle .
Confir m tha t eac h airba g assembl y i s
securel y mounted ; otherwise , sever e persona l injur y
coul d resul t fro m deployment .
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e
radio , the n writ e dow n th e frequencie s fo r th e
radio' s prese t buttons .
2 . Disconnec t th e batter y negativ e cable , the n discon -
nec t th e positiv e cable .
3 . Confir m tha t th e specia l too l i s functionin g properl y
by followin g th e chec k procedur e o n th e labe l o n
the too l o r th e procedur e o n pag e 24-51 .
Driver' s Airbag :
4 . Remov e th e acces s panel , the n disconnec t th e 2 P
connecto r betwee n th e driver' s airba g an d th e cabl e
reel .
DRIVER' SAIRBAGCABLE REE L2P CONNECTO R
ACCESSPANEL
DRIVER' S AIRBA G
2 P CONNECTO R
Front Passenger' s Airbag :
5.Remov e th e glov e box , the n disconnec t th e 2 P o r 3 P
connecto r betwee n th e fron t passenger' s airba g an d
SR S mai n harness .
SRS MAI N HARNES SCONNECTO R
6.
FRON T PASSENGER' SAIRBAGCONNECTO R
Cut of f th e airba g connector , stri p th e end s o f th e
airba g wires , an d connec t th e specia l too l alligato r
clip s t o th e airbag . Plac e th e specia l too l approxi -
matel y thirt y fee t (1 0 meters ) awa y fro m th e airbag .
DRIVER' SAIRBAG
FRONT
PASSENGER' S
AIRBAG
ALLIGATO RCLIPS(Yellow )
12 VOL T BATTER Y
ALLIGATO RCLIPS(Yellow )
OPERATIO N
SWITC H
DEPLOYMEN T
TOO L
07HA Z - SG0040 0
ProCarManuals.com

Cable Ree l
Replacemen t
Store a remove d airba g wit h th e pa d sur -
fac e up . I f th e airba g i s improperl y store d fac e down ,
accidenta l deploymen t coul d prope l th e uni t wit h
enoug h forc e to caus e seriou s injury .
CAUTION :
Alway s disconnec t th e airba g connecto r whe n th e
SR S mai n harnes s is disconnected .
D o no t disassembl e o r tampe r wit h th e airbag .
NOTE : Carefull y inspec t th e airba g befor e installin g it .
D o no t instal l a n airba g tha t show s sign s o f bein g
droppe d o r improperl y handled , suc h a s dents , crack s o r
deformation .
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e
radio , the n writ e dow n th e frequencie s fo r th e
radio' s prese t buttons .
2. Disconnec t th e batter y negativ e cable , the n discon -
nec t th e positiv e cabl e fro m th e battery , an d wai t a t
leas t thre e minutes .
3 . Remov e th e acces s pane l fro m th e steerin g wheel ,
the n disconnec t th e 2 P connecto r betwee n th e driv -
er' s airba g an d cabl e reel .
DRIVER' SAIRBAG
CABLE REE L
2 P CONNECTO R
ACCESSPANEL
DRIVER' S AIRBA G
2 P CONNECTO R
4. Mak e sur e th e wheel s ar e aligne d straigh t ahead .
5 . Remov e th e dashboar d lowe r cover .
6 . Remov e th e driver' s airba g assembl y fro m th e
steerin g whee l (tw o T3 0 Tor x bolts) .
TORX BOLT S
Us e a Tor x T3 0 bit .
DRIVER' SAIRBAG
DASHBOAR D LOWE R COVE R
ProCarManuals.com

17. Tighten the steering wheel bolt to the specified

torque. Then install the driver's airbag.

TORX BOLTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Replace.

Use a Torx T30 bit.

STEERING WHEEL BOLT

38 N-m (3.9 kgf-m, 28 Ibf-ft)
DRIVER'S

AIRBAG

18. Attach the cable reel 2P connector to the connector

holder. Then install the dashboard lower cover.

CONNECTOR

HOLDER

CABLE REEL

2P CONNECTOR

SRS
MAIN

HARNESS

DASHBOARD LOWER COVER
19. Reconnect the driver's airbag 2P connector to the

cable reel 2P connector, and reinstall the access

panel on the steering wheel.

20. Reconnect the battery positive cable, then the nega-

tive cable.

21. After installing the cable reel, confirm proper sys-

tem operation:

Turn the ignition ON (II); the SRS indicator light

should come on for about six seconds and then

go
off.

Make sure both horn buttons work.

Make sure the headlight and wiper switches

work.

Go for a test drive, and make sure the cruise con-

trol switches work.

22. Enter the anti-theft code for the radio, then enter the

customer's radio station presets.ProCarManuals.com

SRS Uni t
Replacemen t
CAUTION:
Durin g installatio n o r replacement , d o no t bum p
(impac t wrench , hamme r etc. ) th e are a nea r th e SR S
unit .
D o no t damag e th e SR S uni t terminal s o r connec -
tors.
Do no t disassembl e th e SR S unit ; i t ha s n o service -
abl e parts .
Stor e th e SR S uni t i n a clean , dr y area .
D o no t us e an y SR S uni t whic h ha s bee n subjecte d
t o wate r damag e o r show s sign s o f bein g droppe d o r
improperl y handled , suc h a s dents , crack s o r defor -
mation .
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e
radio , the n writ e dow n th e frequencie s fo r th e
radio' s prese t buttons .
2 . Disconnec t th e batter y negativ e cable , the n discon -
nec t th e positiv e cabl e fro m th e battery , an d wai t a t
leas t thre e minutes .
3 . Disconnec t th e airba g connectors .
Driver' s Side :
Remov e th e acces s pane l fro m th e steerin g wheel ,
the n disconnec t th e 2 P connecto r betwee n th e driver' s
airba g an d cabl e ree l (se e pag e 24-11 ).
Fron t Passenger' s Side :
Remov e th e glov e box .
Disconnec t th e connecto r betwee n th e fron t passen -
ger' s airba g an d SR S mai n harness . O n a '9 6 model ,
connec t th e shor t connecto r t o th e fron t passenger' s
airba g connector .
FRONT PASSENGER' S
AIRBA G
CONNECTO R
SRS MAI N HARNES SCONNECTO R
4. Remov e th e radi o pane l (se e sectio n 23 ).
5 . Remov e th e cente r consol e an d dashboar d cente r
trim.
DASHBOAR D CENTE R TRI M
CENTE R
CONSOL E
6. Disconnec t th e SR S mai n harnes s 18 P connecto r fro m
th e SR S
unit .
7. Remov e th e fou r Tor x bolt s fro m th e SR S unit , the n
pull th e SR S uni t ou t o f th e dashboard .
TORX BOLT S
Us e a Tor x T3 0 bit .
SRS MAI N HARNES S18P CONNECTO R TOR
X BOLT SUse a Tor x T3 0 bit .
ProCarManuals.com

8. Install the new SRS unit.

TORX BOLTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Use a Torx T30 bit.

Replace.

SRS MAIN HARNESS

18P CONNECTOR

TORX BOLTS

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

Use a Torx T30 bit.

Replace.

9. Connect the SRS main harness 18P connector to the

SRS unit, then push it into position until it clicks.

10. Reinstall the radio panel bracket and radio panel

assembly.

11. Reinstall the dashboard center trim and center con-

sole.
12. Reconnect the driver's airbag 2P connector to the

cable reel 2P connector, and reinstall the access

panel on the steering wheel.

13. Reconnect the front passenger's airbag connector

to the SRS main harness, then reinstall the glove

box.

14. Reconnect the battery positive cable, then the nega-

tive cable.

15. After installing the SRS unit, confirm proper system

operation: Turn the ignition switch ON (II); the SRS

indicator light should come on for about six sec-

onds and then go off.

16. Enter the anti-theft code for the radio, then enter the

customer's radio station presets.ProCarManuals.com

Engine Removal/Installation

Removal

• Make sure jacks and safety stands are placed properly

and hoist brackets are attached to the correct positions

on the engine.

• Make sure the car will not roll off stands and fall

while you are working under it.

CAUTION:

• Use fender covers to avoid damaging painted sur-

face.

• Unplug the wiring connectors carefully while holding

the connector portion to avoid damage.

• Mark all wiring and hoses to avoid misconnection.

Also, be sure that they do not contact other wiring

or hoses or interfere with other parts.

1. Secure the hood open as far as possible.

2. Make sure you have the anti-theft code for the radio,

then write down the frequencies for the radio's pre-

set buttons.

3. Disconnect the battery negative terminal first, then

the positive terminal.

4. Remove the engine ground cables and ignition coil

wire.

IGNITION COIL

WIRE

GROUND

CABLES
6 x 1.0 mm

9.8 N-m (1.0 kgf-m,

7.2 Ibf-ft)
5. Remove the battery, then remove the heat shields.

6 x 1.0 mm

9.8 N-m (1.0 kgf-m, 7.2 Ibf-ft)

HEAT

SHIELDS

6. Remove the battery base.
6 x 1.0 mm

9.8 N-m (1.0 kgf-m,

7.2 Ibf-ft)

8 x
1.25
mm

22 N-m (2.2 kgf-m, 16 Ibf-ft)

BATTERY

BASEProCarManuals.com

Check tha t th e sprin g cli p o n th e en d o f eac h drive -
shaf t click s int o place .
CAUTION : Us e ne w sprin g clips .
Refil l th e coolin g system .
Blee d ai r fro m th e coolin g syste m a t th e blee d bol t
wit h th e heate r valv e ope n (se e pag e 10-5 ).
Adjus t th e throttl e cabl e (se e sectio n 11 ).
Adjus t th e shif t cabl e (se e sectio n 14 ).
Adjus t th e tensio n o f th e followin g driv e belts .
Alternato r bel t (se e sectio n 23 ).
P/ S pum p bel t (se e sectio n 17 ).
A/ C compresso r bel t (se e sectio n 22 ).
Clea n th e batter y post s an d cabl e terminal s wit h sand -
paper , assembl e them , the n appl y greas e t o preven t
corrosion .
Inspec t fo r fue l leakag e (se e sectio n 11 ).
Afte r assemblin g fue l lin e parts , tur n o n th e igni -
tio n switc h (d o no t operat e th e starter ) s o tha t th e
fue l pum p operate s fo r approximatel y tw o sec -
ond s an d th e fue l lin e pressurizes .
Repea t thi s operatio n tw o o r thre e times , an d
chec k fo r fue l leakag e a t an y poin t i n th e fue l line .
Refil l th e engin e wit h engin e oi l (se e pag e 8-4 ).
Refil l th e transmissio n wit h AT F (se e sectio n 14 ).
Refil l th e differentia l wit h differentia l oi l (se e sectio n 15).
Enter th e anti-thef t cod e fo r th e radio , the n ente r th e
customer' s radi o statio n presets .
ProCarManuals.com

Cylinder Hea d
Remova l
Engine remova l i s no t require d fo r thi s procedure .
Mak e sur e jack s an d safet y stand s ar e
place d properl y an d hois t bracket s ar e attache d to cor -
rec t positio n o n th e engine .
CAUTION :
• Us e fende r cover s t o avoi d damagin g painte d sur -
faces .
• Unplu g th e wirin g connector s carefull y whil e holdin g
th e connecto r portio n to avoi d damage .
• T o avoi d damagin g th e cylinde r head , wai t unti l th e
engin e coolan t temperatur e drop s belo w 100° F
(38°C ) befor e loosenin g th e retainin g bolts .
NOTE :
• Mar k al l wirin g an d hose s t o avoi d misconnection .
Also , b e sur e tha t the y d o no t contac t othe r wirin g o r
hoses , o r interfer e wit h othe r parts .
• Inspec t th e timin g bel t befor e removin g th e cylinde r
head .
• Tur n th e crankshaf t pulle y s o tha t th e No . 1 pisto n i s
a t to p dea d cente r (se e pag e 6-12 ).
1 . Mak e sur e yo u hav e th e anti-thef t cod e fo r th e radio ,
the n writ e dow n th e frequencie s fo r th e radio' s pre -
se t buttons .
2 . Disconnec t th e negativ e termina l fro m th e battery .
3 . Drai n th e engin e coolan t (se e pag e 10-5 ).
Remov e th e radiato r cap to spee d draining .
4 . Remov e th e groun d cabl e an d ignitio n coi l wire .
IGNITIO N COI LWIRE6 x 1. 0 m m9.8 N- m (1. 0 kgf-m ,
7. 2 Ibf-ft )
GROUN DCABLE
5. Remov e th e hea t shield s (se e pag e 5-3 ).
6 . Remov e th e intak e ai r duc t (se e pag e 5-4 ).
7 . Loose n th e adjustin g bolt , locknu t an d mountin g bolt ,
the n remov e th e powe r steerin g (P/S ) pum p bel t (se e
page 5-4 ).
8 . Loose n th e idle r pulle y cente r nu t an d adjustin g bolt ,
the n remov e th e ai r conditionin g (A/C ) compresso r
belt .
ADJUSTIN GBOLT
A/ C COMPRESSO R
BELTIDLE R PULLE YCENTER NU T10 x 1.2 5 mm44 N- m (4. 5 kgf-m , 3 3 Ibf-ft )
9. Loose n th e adjustin g bolt , loc k bol t an d mountin g
bolt , the n remov e th e alternato r belt .
MOUNTIN G BOL T10 x 1.2 5 mm44 N- m (4. 5 kgf-m ,
3 3 Ibf-ft )ADJUSTIN GNUT
LOC K BOL T8 x 1.2 5 mm22 N- m (2. 2 kgf-m , 1 6 Ibf-ft )
ALTERNATO R
BELT
ProCarManuals.com