Trans Acura TSX 2010 Owner's Guide

The master key can be retracted into
theremotetransmitter.Tousethe
key, push the release button to
release the key f rom the transmitter.
The key should be f ully extended.
To retract the key, push the release
buttonandatthesametimepushthe
key into the remote transmitter until
it is securely latched.Thekeymaycomeincontactwith
your f inger while being retracted or
extended. Make sure your f ingers do
not touch the pivot of the key when
retracting or extending the key. Always make sure the key is f ully
extended when you insert it to the
ignition switch. If the key is not f ully
extended, the immobilizer system
may not operate properly and
prevent the engine f rom starting.
Retractable Master Key
Keys and Locks
120
Push
RELEASE BUTTON
2010 TSX

µ
µ
µ
The ignition switch has f our
positions: LOCK (0), ACCESSORY
(I), ON (II), and START (III). If you turn the ignition key to the
ACCESSORY (I) position with the
driver’s door closed, you will see an
‘‘ACCESSORY (I) POSITION’’
message on the multi-inf ormation
display to inf orm you of the key
position.
This is the normal key
position when driving. Several of the
indicators on the instrument panel
come on as a test when you turn the
ignition switch f rom the
ACCESSORY (I) to the ON (II)
position.
If the f ront wheels are turned, the
anti-thef t lock may make it dif f icult
to turn the key. Firmly turn the
steering wheel to the lef t or right as
you turn the key. You can insert or
remove the key only in this position.
To turn the key, push it in slightly. If
your vehicle has an automatic
transmission, the shif t lever must
also be in Park.
You can
operate the audio system and the
accessory power sockets in this
position.
If you leave the key in the ignition
switch in the ACCESSORY (I)
position and open the driver’s door,
you will see a ‘‘RETURN IGNITION
SWITCH TO LOCK (0) POSITION’’
message on the multi-inf ormation
display and hear a reminder beeper.
Ignition Switch
ON (II)
LOCK (0)
A CCESSORY (I)
122
2010 TSX

µUse this position
only to start the engine. The switch
returns to the ON (II) position when
you let go of the key.
You will hear a reminder beeper if
you leave the key in the ignition
switch in the LOCK (0) or the
ACCESSORY (I) position and open
thedriver’sdoor.Removethekeyto
turn of f the beeper.
You will also see a ‘‘REMOVE KEY’’
message on the multi-inf ormation
display.
If your vehicle has an automatic
transmission, the shif t lever must be
in Park bef ore you can remove the
key f rom the ignition switch.
Ignition Switch
ST A RT (III)
Inst rument s and Cont rols
123
Removing the key from the
ignition switch while driving
locks the steering. This can
cause you to lose control of the
vehicle.
Remove the key from the
ignition switch only when
parked.
2010 TSX

µµ
Press this button once to
lock all doors. Some exterior lights
will f lash. When you push LOCK
twice within 5 seconds, you will hear
a beep to verify that the doors are
locked and the security system has
set. You cannot lock the doors if any
door is not f ully closed or if the key
is in the ignition switch. Press this button once
to unlock the driver’s door (or all the
doors depending on the door lock
setting). Push it twice to unlock the
remaining doors. Some exterior
lights will f lash twice the f irst time
you push the button. The keyless lock acknowledgment
beep and f lashing of the lights can
be deactivated (see page ).
If you do not open any door within 30
seconds, the doors automatically
relock and the security system sets.
The ceiling light and the door
activated spotlights come on when
you press the UNLOCK button if the
lights are in the door activated
position. If you do not open any door
within 30 seconds (or whatever
setting of the interior light dimming
time is set to), the light(s) will f ade
out. If you relock the doors with the
remote transmitter before 30
seconds have elapsed, the light(s)
will go of f immediately. To change the lock/unlock setting
and the relock timer setting, refer to
the customized settings on page .
Locking and unlocking the driver’s
door will also lock and unlock the
f uel f ill door (see page ).
You can also open all power windows
and the moonroof f rom outside the
vehicle with the remote transmitter
(see page ).
103
99
347
149
Remote Transmitter
LOCK UNL OCK
126
LED
LOCK BUTTON
UNLOCK
BUTTON PANIC
BUTTON
TRUNK
BUTTON
2010 TSX

µµ When you unlock the driver’s door
with your remote transmitter, each
remote transmitter activates the
customized settings related to that
remote.
Press and hold this
button for about 1 second to attract
attention; the horn will sound, and
the exterior lights will f lash f or about
30 seconds. To cancel panic mode,
press any other button on the remote
transmitter, or turn the ignition
switch to the ON (II) position. Panic
mode does not work when the key is
in the ignition switch.
Press and hold this
button f or about 1 second to open
the trunk. You cannot open the trunk
if the key is in the ignition switch.
The driving position memory
activated (Driver 1, Driver 2) is
shownonthebackof each
transmitter. Make sure you store
your desired driving position in thememory that is activated by the
transmitter you normally carry.
Here are the settings activated with
the remote:
Customized settings
(see page ).
Driving position memory
(see page ).
When you unlock and open the
driver’s door with the remote
transmitter, the driver’s seat moves
to the position stored in memory.
You will hear two beeps when the
movement is completed. The
indicator in the related memory
button on the driver’s door remains
on. 81
142
CONT INUED
All models except Canadian TSX with 4-cylinder engine
Recalling a Memorized Driving
Position
PA NIC
TRUNK
Remote Transmitter
Inst rument s and Cont rols
127
With Driver 2
With Driver 1
2010 TSX

Avoid dropping or throwing the
transmitter.
Protect the transmitter from
extreme temperature.
Do not immerse the transmitter in
any liquid.
If you lose a transmitter, the
replacement needs to be
reprogrammed by your dealer.
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616 Separate the keypad from the
transmitter by pushing any button
f rom outside.Be caref ul when removing
this screw as the head of the screw
can strip out. Remove the screw at the base of
the transmitter with a small
Phillips-head screwdriver.
To replace the battery:
To turn the memory position link
settings back on, repeat this
procedure. The LED will blink once
to indicate the feature has been
turned on. You can turn of f this driving position
memory activation. Press and hold
the LOCK and UNLOCK buttons at
thesametime.TheLEDinthe
remote transmitter will blink twice.
Then release the buttons. Doing this
also cancels the memory position
link setting f or that remote and
restores the default settings. You will also see the ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ message on the multi-
inf ormation display, depending on
which linked remote transmitter is
used.
1.
2.
Remote Transmitter
Remote Transmitter Care
Replacing the Transmitter
Battery
128
NOTE:
KEYPAD
SCREW
2010 TSX

´
As required by the FCC:This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.Remove the old battery and note
the polarity. Make sure the
polarity of the new battery is the
same ( side f acing down), then
insert it in the keypad.
Place a cloth on the edge of the
keypad to prevent scratches, and
remove the upper half by carefully
prying on the edge with a small
f lat-tip screwdriver. An improperly disposed of battery
can hurt the environment.
Always conf irm local regulations f or
battery disposal.
Snap the two halves of the keypad,
then install the parts in reverse
order.
4.
5.
3.
Remote Transmitter
Inst rument s and Cont rols
129
BATTERY
2010 TSX

The trunk will lock when you lock
the driver’s door with the key, the
remote transmitter, either master
door lock switch, or the lock tab on
the driver’s door.To open the trunk f rom the outside,
push the release switch, then lif t up.Youcanalsoopenthetrunkineither
of two ways:
Push the trunk release button on
the driver’s door.
Press and hold the trunk release
button on the remote transmitter.
To unlock the trunk, turn the key
twice to unlock the doors, push the
rear of either master door lock
switch, or push UNLOCK twice on
the remote transmitter.
Trunk
130
TRUNK RELEASE
SWITCH
TRUNK RELEASE BUTTON
2010 TSX

To close the trunk, use the inner
handle to lower the lid, then press
down on the back edge.
Keep the trunk lid closed at all times
while driving to avoid damaging it,
and to prevent exhaust gas from
getting into the interior. See,page . To protect items in the trunk, you
can disable the trunk release button
on the driver’s door and the trunk
release switch on the trunk lid by
turning of f the trunk main switch in
the glove box and locking the glove
box. Make sure either rear seat is
not f olded down.
If you need to give the key to
someone else, give them the valet
key. Even if the trunk release is locked
with the main switch, you can open
the trunk with the remote
transmitter.
Your vehicle is equipped with the
emergency f uel lid release in the
trunk. Refer to page for how to
access it.
55 474
Trunk
Carbon
Monoxide Hazard Trunk Main Switch
Emergency Fuel L id Release
Inst rument s and Cont rols
131
MAIN SWITCH
ONOFF
2010 TSX

Store a driving position only when
the vehicle is parked.Turn the ignition switch to the ON
(II) position. You cannot add a
new driving position to the
memory unless the ignition switch
is in the ON (II) position. You can
recall a memorized position with
the ignition switch in any position.
Adjust the seat to a comfortable
position (see page ). Press and release the SET button
on the control panel. You will hear
a beep. Immediately press and
hold one of the memory buttons (1
or 2) until you hear two beeps.
The indicator in the memory
button will come on. The current
position of the driver’s seat is now
stored.
Your vehicle has a memory feature
f or the driver’s seat position.
Two seat positions can be stored in
separate memories. You select a
memorized position by pushing the
appropriate button or using the
appropriate remote transmitter
(Driver 1 or Driver 2).
This setting can be linked or
unlinked with the remote transmitter.
To switch the link setting, see page
. 3.
1.
2.
134
93
All models except Canadian TSX with
4-cylinder engineStoring a Driving Position in
Memory
Driving Position Memory System
142
MEMORY BUTTONS
SET BUTTON
2010 TSX