Acura TSX 2011 Owner's Manual

If a Tire Goes Flat
Changing a Flat Tire
280Handling the Unexpected
WARNING
The vehicle can easily roll off the jack,
seriously injuring anyone underneath.
Follow the directions for changing a tire
exactly, and never get under the vehicle
when it is supported only by the jack.
How to Set Up the Jack
How to Set Up the Jack
Do not use the jack with people or luggage in the
vehicle.
Use the jack provided in your vehicle.
Other jacks may not support the weight
("load") or
their shape may not match.
The following instructions must be followed to use
the jack safely.
Do not use while the engine is running. tUse only where the ground is firm and level. tUse only at the jacking points. tDo not get in the vehicle while using the jack. tDo not put anything on top of or underneath the tjack.
1. Place the jack under the jacking point
closest to the tire to be changed.
2. Turn the end bracket (as shown in the
image) clockwise until the top of the jack
contacts the jacking point.
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the extension bar
and the jack handle, until the tire is off the
ground.
Extension Bar
Wheel Nut
Wrench as Jack
Handle

If a Tire Goes Flat
Changing a Flat Tire
281
Continued
Handling the Unexpected
Replacing the Flat Tire
1. Remove the wheel nuts and flat tire.2. Wipe the mounting surfaces of the wheel
with a clean cloth.
3. Mount the compact spare tire.
4. Screw the wheel nuts until they touch the
lips around the mounting holes, and stop
rotating.
5. Lower the vehicle and remove the jack.
Tighten the wheel nuts in the order
indicated in the image. Go around,
tightening the nuts, two to three times in
this order.
Wheel nut torque:
80 lbf∙ft (108 N∙m, 11 kgf∙m)
Replacing the Flat Tire
Do not over tighten the wheel nuts by applying
extra torque using your foot or a pipe.

If a Tire Goes Flat
Changing a Flat Tire
282Handling the Unexpected
WARNING
Loose items can fly around the interior
in a crash and can seriously injure the
occupants.
Store the wheel, jack, and tools securely
before driving.
Storing the Flat Tire
1. Remove the center cap and place the flat
tire face down in the spare tire well.
2. Remove the spacer cone from the wing
bolt, flip it over, and insert it back on the
bolt. Secure the flat tire with the wing
bolt.
3. Securely put the jack and wheel nut
wrench back in the tool case. Store the
case in the trunk.
Storing the Flat Tire
TPMS and the Spare Tire
If you replace a flat tire with the spare tire, the low tire pressure/ TPMS indicator
comes on while you are driving. After driving for a few miles (kilometers), the
indicator will start blinking for a short time and then stay on. "CHECK TPMS
SYSTEM" appears on the multi-information display, but this is normal.
If you replace the tire with a specified regular tire, the warning message on the
multi-information display and the TPMS indicator will go off after a few miles
(kilometers).
TPMS and the Spare Tire
The system cannot monitor the pressure of the
spare tire. Manually check the spare tire pressure to
be sure that it is correct.
Use TPMS specific wheels. Each is equipped with a
tire pressure sensor mounted inside the tire behind
the valve stem.
Wing
Bolt
For
normal
tire For
compact
spare tire Spacer
Cone

283
Engine Does Not Start
Handling the Unexpected
Checking the EngineIf the engine does not start, turn the ignition switch to START III
and check the
starter.
Checking the Engine
If you must start the vehicle immediately, use an
assisting vehicle to jump start it.
Jump Starting


P. 2 8 4

Starter condition Checklist
Starter doesn't turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.Check brightness of the interior light.
Turn on interior lights and check brightness.
If the interior lights are dim or do not come on at all t
 Battery Inspection and Maintenance P. 2 6 8
If the interior lights come on normally t
Fuse Inspection and Replacement
P. 2 9 4
The starter turns over normally
but the engine doesn't start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.Review the engine start procedure.
Follow its instructions, and try to start the engine again.
Starting the Engine P.1 9 1
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
 Immobilizer System P. 9 8
Check the fuel level.
There should be enough fuel in the tank.
Fuel Gauge P. 7 5
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
 Inspecting and Changing Fuses P. 2 9 7
If the problem continues:
 Emergency Towing P. 2 9 8

Jump Starting
284Handling the Unexpected
Jump Starting Procedure
Turn off the power to electric devices, such as audio and lights. Turn off the
engine, then open the hood.
Jump Starting
6-cylinder models 1. Slide out the battery terminal cover. All models 2. Connect the first jumper cable to your
vehicle's battery
terminal.
3. Connect the other end of the first jumper
cable to the assisting vehicle's
terminal.
Use a 12-volt booster battery only.
4. Connect the second jumper cable to the
assisting vehicle's
terminal.
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
4-cylinder models 6-cylinder models Booster Battery
Cover

285
Continued
Handling the Unexpected
Battery performance degrades in cold conditions
and may prevent the engine from starting. Jump Starting
5. Connect the other end of the second
jumper cable:
4 -cylinder models with automatic transmission

Engine mounting bolt
4 -cylinder models with manual transmission

Transmission mounting bolt
6-cylinder models

Engine hanger
Do not connect this jumper cable to any
other part of the engine.
6. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine
and increase its rpm slightly.
7. Attempt to start your vehicle's engine. If
it turns over slowly, check that the jumper
cables have good metal-to-metal contact.
Jump Starting
6-cylinder models 4-cylinder models with
automatic transmission 4-cylinder models with
manual transmissionBooster Battery

286Handling the Unexpected
Jump Starting What to Do After the Engine Starts
Once your vehicle's engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
3. Disconnect the jumper cable from your vehicle's battery
terminal.
4. Disconnect the other end of the jumper cable from the assisting vehicle's
battery
terminal.
Have your vehicle inspected by a nearby service station or a dealer.
6-cylinder models

287
Shift Lever Does Not Move
Handling the Unexpected
Automatic transmission models Follow the procedure below if you cannot move the shift lever out of P
position.
1. Set the parking brake.
2. Remove the key from the ignition switch.
3. Wrap a cloth around the tip of a small flat-
tip screwdriver and remove the cover of
the shift lock release slot.
Put the tip of the flat-tip screwdriver
into the slot and remove it as shown in
the image.
4. Insert the key into the shift lock release
slot.
5. While pushing on the key, press the shift
lever release button and place the shift
lever into N
.
The lock is now released. Have the shift
lever checked by a dealer as soon as
possible.
Releasing the Lock
Cover
Slot
Release Button
Shift Lock Release Slot

Overheating
288Handling the Unexpected
How to Handle OverheatingOverheating symptoms are as follows:
The temperature gauge needle is at the tH
mark or the engine suddenly loses
power.
Steam is coming out of the engine compartment. t
First thing to do
1. Immediately park the vehicle in a safe place. Automatic transmission models
Move the shift lever to P
and set the parking brake. Turn off all accessories
and turn on the hazard warning lights.
Manual transmission models
Move the shift lever to N
and set the parking brake. Turn off all accessories
and turn on the hazard warning lights.
2. No steam coming out: Keep the engine running and open the hood.
Steam coming out: Turn off the engine and wait until steam goes away.
Then, open the hood.
How to Handle Overheating NOTICE Continuing to drive with the temperature gauge
needle at the
H
mark may damage the engine.WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood or engine
compartment if steam is coming out.

Overheating
How to Handle Overheating
289
Handling the Unexpected
Last thing to do
Once the engine has cooled sufficiently, restart it and check the temperature
gauge.
If the temperature gauge needle has gone down, resume driving. If it has not
gone down, contact a dealer for repairs.
How to Handle Overheating
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure
only. Have a dealer flush the system with proper
antifreeze as soon as possible.
Next thing to do
1. Check that the cooling fan is operating
and stop the engine once the temperature
gauge needle comes down.
If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks. If the coolant level in the reserve tank
is low, add coolant until it reaches the
MA X mark. If there is no coolant in the reserve tank,
check that the radiator is cool. Cover
the radiator cap with a heavy cloth and
open the cap. If necessary, add coolant
up to the base of the filler neck, and put
the cap back on.
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to
spray out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve Tank
MAX
MIN