Engine air ACURA CSX 2006 Service Workshop Manual

Î
9-12Intake Manifold and Exhaust System
Exhaust Manifold Removal and Installation (cont’d)
EXHAUST MANIFOLD
COVER
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
10 x 1.25 mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft) GASKET
GASKET
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
10x1.25mm
44 N·m
(4.5 kgf·m, 33 lbf·ft)
SELF-LOCKING NUT
10 x 1.25 mm
44 N·m (4.5 kgf·m, 33 lbf·ft)
EXHAUST MANIFOLD BRACKETHEAT SHIELD
9. Remove the cover and the exhaust manifold bracket, then remove the exhaust manifold.
10. Install the exhaust manifold, and tighten the bolts and nuts in a crisscross pattern in three steps, beginning with the inner bolt.
11. Install the other parts in the reverse order of removal.
12. Inspect for leaks. Turn the ignition switch to ON (II) (do not operate the starter) so the fuel pump runs for about 2 seconds and pressurizes the fuel line. Repeat this operation three times, then check for fuel leakage at any point
in the fuel line.
13. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater valve open (see step 6 on page 10-8).
Tighten the bolts in steps,
alternating side-to-side.Replace.
Replace.
Replace.
08/08/21 14:37:38 61SNR030_090_0012
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

 )
K20Z2 engine
9-13
Exhaust Pipe and Muffler Replacement
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft) 8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
HEAT SHIELD
GASKET MUFFLER
EXHAUST PIPE B
SELF-LOCKING NUTS
10x1.25mm
33N·m(3.4kgf·m,25lbf·ft) GASKET
GASKET THREE WAY CATALYTIC CONVERTER
(TWC) ASSEMBLY
SECONDARY HEATED
OXYGEN SENSOR
(SECONDARY HO2S)
44N·m(4.5kgf·m,33lbf·ft)
AIR FUEL RATIO (A/F) SENSOR
44 N·m (4.5 kgf·m, 33 lbf·ft) 8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
NOTE: Use new gaskets and self-locking nuts when reassembling.
Tighten the bolts in steps,
alternating side-to-side.
Replace.
Replace. Replace.
Replace. Tighten the bolts in steps,
alternating side-to-side.
08/08/21 14:37:38 61SNR030_090_0013
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

 )
K20Z3 engine
9-14Intake Manifold and Exhaust System
Exhaust Pipe and Muffler Replacement (cont’d)
8 x 1.25 mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
8x1.25mm
22 N·m (2.2 kgf·m, 16 lbf·ft)
HEAT SHIELD
GASKET MUFFLER
EXHAUST PIPE B
SELF-LOCKING NUTS
10x1.25mm
33 N·m
(3.4 kgf·m, 25 lbf·ft)
GASKET
THREE WAY CATALYTIC CONVERTER
(TWC) ASSEMBLY
SECONDARY HEATED
OXYGEN SENSOR
(SECONDARY HO2S)
44 N·m (4.5 kgf·m, 33 lbf·ft)
AIR FUEL RATIO (A/F) SENSOR
44 N·m (4.5 kgf·m, 33 lbf·ft) GASKET
6x1.0mm
10 N·m
(1.0 kgf·m, 7.2 lbf·ft)
NOTE: Use new gaskets and self-locking nuts when reassembling.
Tighten the bolts in steps,
alternating side-to-side.
Tighten the bolts in steps,
alternating side-to-side.
Replace.
Replace.
Replace.
Replace.
08/08/21 14:37:39 61SNR030_090_0014
ProCarManuals.com
DYNOMITE -2009-


(#'


") 
(#'


 )
K20Z2 engine
10-610-6 Cooling System
Water Pump Inspection
Water Pump Replacement
A
A
B
A
6x1.0mm
12 N·m (1.2 kgf·m, 8.7 lbf·ft)
1. Remove the drive belt (see page 4-31).
2. Turn the water pump pulley counterclockwise, and check that it turns freely and smoothly. If it does not
turn smoothly, replace the water pump (see page
10-6).
NOTE: When you check the water pump, you may
see a small amount of ‘‘weeping’’ from the bleed
holes (A). This is normal.
3. Install the drive belt (see page 4-31). 1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley
(see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the six bolts securing the water pump, then remove the water pump (A).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with a new O-ring (B).
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
08/08/21 14:39:57 61SNR030_100_0006
ProCarManuals.com
DYNOMITE -2009-


(#'


 )

(#'


")
K20Z3 engine
10-710-7
Coolant Check
A B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) C A
B
1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley (see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the oil cooler joint pipe (A), then remove the seven bolts securing the water pump. Remove
the water pump (B).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with new O-rings (C) and the oil cooler joint pipe.
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8). 1. Check the coolant level in the coolant reservoir.
Make sure it is between the MAX mark (A) and MIN
mark (B).
2. If the coolant level in the coolant reservoir is at or below the MIN mark, add coolant to bring it up to
the MAX mark, then inspect the cooling system for
leaks.
08/08/21 14:39:58 61SNR030_100_0007
ProCarManuals.com
DYNOMITE -2009-


(#'


 )

(#'


")
K20Z3 engine
10-710-7
Coolant Check
A B
C
6x1.0mm
12 N·m
(1.2 kgf·m, 8.7 lbf·ft) C A
B
1. Remove the drive belt (see page 4-31).
2. Drain the engine coolant (see page 10-8).
3. Remove the drive belt auto-tensioner pulley (see page 4-33).
4. Remove the crankshaft pulley (see page 6-16).
5. Remove the oil cooler joint pipe (A), then remove the seven bolts securing the water pump. Remove
the water pump (B).
6. Inspect, and clean the O-ring groove and mating surface of the water passage.
7. Install the water pump with new O-rings (C) and the oil cooler joint pipe.
8. Clean up any spilled engine coolant.
9. Install the crankshaft pulley (see page 6-17).
10. Install the drive belt auto-tensioner pulley (see page 4-33).
11. Install the drive belt (see page 4-31).
12. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8). 1. Check the coolant level in the coolant reservoir.
Make sure it is between the MAX mark (A) and MIN
mark (B).
2. If the coolant level in the coolant reservoir is at or below the MIN mark, add coolant to bring it up to
the MAX mark, then inspect the cooling system for
leaks.
08/08/21 14:39:58 61SNR030_100_0007
ProCarManuals.com
DYNOMITE -2009-

Î
(#'

 )
10-10Cooling System
Thermostat Replacement
THERMOSTAT ASSEMBLY
HARNESS CLAMP LOWER RADIATOR HOSE 6x1.0mm
10 N·m (1.0 kgf·m, 7.2 lbf·ft)O-RING
1. Drain the engine coolant (see page 10-8).
2. Remove the splash shield (see step 25 on page 5-5).
3. Remove the lower radiator hose, then remove the thermostat.
4. Install the new thermostat assembly with a new O-ring, then install the lower radiator hose.
5. Install the splash shield (see step 40 on page 5-20).
6. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater valve open (see
step 6 on page 10-8).
7. Clean up any spilled engine coolant.
Replace.
08/08/21 14:39:59 61SNR030_100_0010
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal - K20Z2 engine
10-1310-13
EGR Passage Removal and
Installation
A
B
A B
C
20. Install the intake manifold:
 K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
21. Install the A/C compressor (see step 28 on page 5-19).
22. Install the A/C condenser fan shroud assembly.
23. Install the alternator (see page 4-36).
24. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
25. Clean up any spilled engine coolant. 1. Drain the engine coolant (see page 10-8).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the harness holder (A) from the bracket,
then remove the harness holder bracket (B).
4. Disconnect the upper radiator hose (A), the heater hose (B), and the water bypass hose (C).
(cont’d)
08/08/21 14:40:01 61SNR030_100_0013
ProCarManuals.com
DYNOMITE -2009-



(#'
 )
Removal - K20Z2 engine
10-1310-13
EGR Passage Removal and
Installation
A
B
A B
C
20. Install the intake manifold:
 K20Z2 engine (see page 9-4)
 K20Z3 engine (see page 9-9)
21. Install the A/C compressor (see step 28 on page 5-19).
22. Install the A/C condenser fan shroud assembly.
23. Install the alternator (see page 4-36).
24. Refill the radiator with engine coolant, and bleed the air from the cooling system with the heater
valve open (see step 6 on page 10-8).
25. Clean up any spilled engine coolant. 1. Drain the engine coolant (see page 10-8).
2. Remove the air cleaner assembly (see page 11-345).
3. Remove the harness holder (A) from the bracket,
then remove the harness holder bracket (B).
4. Disconnect the upper radiator hose (A), the heater hose (B), and the water bypass hose (C).
(cont’d)
08/08/21 14:40:01 61SNR030_100_0013
ProCarManuals.com
DYNOMITE -2009-




Installation - K20Z2 engine
10-15
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A
B
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A B
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
8x1.25mm
22 N·m
(2.2 kgf·m, 16 lbf·ft)
A B
C
1. Install the EGR valve (A), with a new gasket (B).
2. Install the EGR passage (A) with a new gasket (B). 3. Install the air cleaner brackets.
4. Connect the upper radiator hose (A), the heater
hose (B), and the water bypass hose (C).
(cont’d)
08/08/21 14:40:02 61SNR030_100_0015
ProCarManuals.com
DYNOMITE -2009-