ACURA NSX 1997 Service Repair Manual

Rear Hatc h Glas s
Installatio n
NOTE:
• D o no t scrap e dow n t o th e painte d surfac e of the
hatc h frame ; damage d pain t wil l interfer e wit h pro -
per bonding .
• Mas k of f surroundin g surface s befor e painting .
1. Us e a putt y knif e t o scrap e of f al l trace s of old
adhesiv e an d outer/inne r rubbe r dams , the n clea n
th e rea r hatc h fram e an d glas s (new ) surfac e wit h
alcoho l wher e ne w adhesiv e i s t o b e applied .
NOTE : Mak e sur e th e bondin g surfac e i s kep t fre e
o f water , oi l an d grease .
CAUTION : Avoi d settin g th e glas s o n it s edges ;
smal l chip s ma y late r develop into cracks .
GLASS
REAR HATC H
FRAM E
Clean th e oute rsurface .
Clean th eshadowe darea.
ProCarManuals.com

Rear Hatc h Glas s
Installatio n (cont'd )
2. Instal l th e rea r hatc h frame , an d adjus t i t fi t t o th e
weatherstri p an d engin e cove r seal .
NOTE : D o no t instal l th e suppor t struts .
REAR HATC H FRAM E
SUPPOR T STRUT S
3. Glu e th e oute r an d inne r rubbe r dam s t o th e insid e
fac e o f th e glass , a s shown , t o contai n th e adhesiv e
durin g installation .
NOTE:
• Alig n th e cente r of the gluin g surfac e wit h th e
printe d dots .
• B e carefu l no t t o touc h th e glas s wher e adhesiv e
wil l b e applied .
• Mas k of f surroundin g surface s befor e applyin g
primer .
GLASS
OUTERRUBBE
RDAM
INNE R RUBBE R DA M
4. Plac e th e glas s gentl y o n th e rea r hatc h frame , the n
cente r i t i n th e opening . Mak e alignmen t mark s b y
markin g line s acros s th e glas s an d bod y wit h a
greas e penci l a t th e fou r point s shown .
NOTE : Pu t severa l spacer s betwee n glas s an d
rea r hatc h ai r scoo p t o preven t th e glas s fro m
slidin g down .
8 m m (0. 3 in)
GLAS S
SPACE R
REARHATC HAIR SCOO P
Apply glas s prime r here .
GLAS S
ENGIN
E COVE R
GLAS SPRINTE
D DOT S GLAS
S
ALIGNMEN T MARK S
5. Wit h a brush , appl y a ligh t coa t of glas s prime r t o
th e glas s a s shown , the n lightl y wip e i t of f wit h
gauz e o r cheesecloth .
NOTE:
• D o no t appl y bod y prime r t o th e glass , an d d o
no t ge t bod y an d glas s prime r brushe s mixe d up .
• Neve r touc h th e prime d surface s wit h you r
hands . I f yo u do , th e adhesiv e ma y no t bon d t o
th e glas s properly , causin g a lea k afte r th e glas s
is installed .
• Kee p water , dust , an d abrasiv e material s awa y
fro m th e prime d surface .
REAR HATC H
FRAM E
GLAS
S
ProCarManuals.com

REAR HATCH

FRAME

INSIDE

7. Thoroughly mix the adhesive and hardener

together on a glass or metal plate.

NOTE:

• Clean the plate with a sponge and alcohol before

mixing.

• Follow the instructions that came with the

adhesive.

8. Before filling a cartridge, cut the end of the nozzle

as shown.

Cut nozzle end

as shown.

10 mm
(0.39
in)

7 mm
(0.3
in)
9. Pack adhesive into the cartridge without air

pockets to ensure continuous delivery. Put the car-

tridge in a calking gun, and run a bead of adhesive

around the edge of the glass as shown.

GLASS

10. Use suction cups to hold the glass over the open-

ing, align it with the alignment marks made in step

4 and set it down on the adhesive. Lightly push on

the glass until its edges are fully seated on the

adhesive all the way around.

NOTE: Do not open or close the doors until the

adhesive is dry.

ALIGNMENT MARKS

GLASS
6. With a brush, apply a light coat of body primer to

the original adhesive remaining around the rear

hatch frame.

NOTE:

• Make sure the surface is kept free of water, oil

and grease.

• Do not apply glass primer to the body, and be

careful not to mix up glass and body primer

brushes.

• Never touch the primed surfaces with your

hands.

Apply body primer here.
ADHESIVE

ADHESIVE

GLASS

REAR HATCH

FRAME
OUTSIDEProCarManuals.com

Rear Hatch Glass

Installation (cont'd)

11. Scrape or wipe the excess adhesive off with a put-

ty knife or towel.

NOTE: Use a soft shop towel dampened with

alcohol to remove adhesive from a painted surface

or glass.

1 2. After the adhesive is dry, spray water over the

glass and check for leaks. Mark leaking areas and

let the glass dry, then seal with sealant.

NOTE: Let the car stand for at least four hours

after glass installation. If the car has to be used

within the first four hours, it must be driven slowly.

13. Remove the spacers.

14. Install the support struts.ProCarManuals.com

Rear Hatc h Glas s Moldin g
Replacemen t
CAUTION:
• Wea r glove s t o replac e th e molding .
• D o no t damag e th e glas s an d defroste r gri d lines .
1 . Remov e th e rea r hatc h assembl y (se e pag e 20-64 ).
2 . Plac e th e rea r hatc h assembl y o n it s surfac e a s
shown .
CAUTION : Avoi d settin g th e glas s o n it s edges ;
smal l chip s ma y late r develo p int o cracks .
3. Wit h a helpe r holdin g th e rea r hatc h assembly ,
carefully cu t of f th e molding .
REAR HATC H ASSEMBLY
PROTECTIVE
COVE R
MOLDIN G
MOLDING
GLASS
GLAS S
4. Tur n th e glas s over , the n cu t th e oute r sid e rubbe r
portion o f th e molding .
MOLDING
GLASS
ProCarManuals.com

6. Clea n th e glas s surfac e wit h alcoho l wher e th e ne w
moldin g is t o b e installed .
NOTE: Mak e sur e th e surfac e is kep t fre e o f water ,
oi l an d grease .
7 . Wit h a brush , appl y a ligh t coa t o f glas s prime r
aroun d th e edg e of the glass .
6 m m(0. 2 in )
SURFAC E
INSIDE SURFAC E6 m m(0. 2 in )
EXCES S PRIME R
GLAS S
NOTE : Scrap e of f exces s glas s prime r wit h a putt y
knif e afte r installin g th e ne w molding .
8 . Degreas e th e inne r surface s o f th e ne w moldin g
thoroughly , the n appl y a ligh t coa t o f glas s prime r
t o th e surfaces .
NOTE:
• Appl y glas s prime r aroun d th e entir e groov e o f
the ne w molding .
• D o no t appl y glas s prime r t o th e oute r surface .
MOLDINGMOLDIN G
9. Ru n a bea d of adhesiv e i n th e groov e o f th e
molding .
ADHESIV E
MOLDIN G
10. Pres s th e moldin g int o positio n aroun d th e entir e
edge of the glass .
NOTE : Chec k tha t th e moldin g i s no t wrinkle d o r
lifte d awa y a t th e corners .
GLASS MOLDIN G
PROTECTIV ECOVER
11. Scrap e o r wip e th e exces s adhesiv e of f wit h a put -
ty knif e o r towel .
NOTE: Us e a sof t sho p towe l dampene d wit h
alcoho l t o remov e adhesiv e fro m a painte d surfac e
o r glass .
(Glass Surface )
MOLDING
EXCESS ADHESIV E
GLASS
Inside:
Surface t o b e
wipe d clean .
5. Scrap e al l trace s o f th e ol d moldin g fro m th e cham -
fere d edge s o f th e glass .
NOTE : B e sur e t o scrap e al l trace s o f th e ol d mold -
ing throughly .
Scrape here . GLAS
S
Outside:
ProCarManuals.com

Headliner/Interior Tri m
Replacemen t
To remov e th e headliner , firs t remov e the :
• Sunvisor s
• Cente r pilla r tri m panel s
• Fron t pilla r tri m panel s
• Seat s (se e pag e 20-39 )
• Ceilin g ligh t (se e sectio n 23 )
NOTE :
• Whe n installin g th e headliner , b e carefu l no t t o fol d
o r ben d it . Also , b e carefu l no t t o scratc h th e body .
• Chec k tha t bot h side s o f th e headline r ar e securel y
attached t o th e trim .
Disassembl e i n numbere d sequence .
NOTE:
• Whe n removin g th e rea r tri m panels , tak e car e no t t o
damag e th e contro l unit s an d relays .
• Tak e car e no t t o scratc h th e tri m panels .
Installatio n i s th e revers e of the remova l procedure .
NOTE : I f necessary , replac e an y damage d clips .
Clip Location s
CENTER ARMRES TReplacement , se e pag e20-49
RELEAS EHANDLEReplacement ,see pag e 20-6 8
ProCarManuals.com

Seats
Replacemen t
NOTE:
• Befor e removin g th e seat , mov e th e sea t unti l yo u
can se e it s mountin g bolt s an d sea t moun t cove r
caps.
• Tak e car e no t t o scratc h th e sea t cover , interio r trim ,
dashboar d an d cente r armrest .
• O n reassembly , replac e th e lowe r ancho r bol t (* ) an d
use liqui d threa d lock .
1. Pr y ou t th e seat moun t cove r caps .
2 . Remov e th e sea t mountin g bolts , the n remov e th e
sea t an d disconnec t th e connector .
3 . Pr y ou t th e cap , an d remov e th e sea t bel t lowe r
ancho r bolt . Remov e th e seat .
SEAT MOUN T
COVE R CA P SEA
T
SEA T MOUNTIN G BOLT S
10 x 1.2 5 mm39 N- m (4. 0 kgf-m , 2 9 Ibf-ft )
CONNECTO R SEA
T MOUNTIN G
BOLTS10 x 1.2 5 mm39 N- m (4. 0 kgf-m ,
2 9 Ibf-ft )
SEA T BEL T
LOWE R ANCHO R
BOLT7/16-2 0 UN F
3 2 N- m (3. 3 kgf-m ,
2 4 Ibf-ft )
I f necessary , remov e th e powe r slid e cable , powe r
seat switc h an d sea t moun t cover .OUTER SLID E
BO X GEA R CLI
P
Pr y here .
HOO K
Pr y here .
POWE R SLID E CABL E
NOTE : Tak e car e no t t o
ben d th e cable .
4. Installatio n i s th e revers e o f th e remova l procedure .
POWER SEA T
SWITC H
Disconnec t th e connectors .
NOTE : Appl y greas e t o th e inne r an d oute r slid e
bo x gears .
SEAT MOUN T COVE R
CORROSIO
N RESISTAN T BOL T
CAP
INNE R SLID E
BO X GEA R
ProCarManuals.com

Seats
Seat Cove r Replacemen t
CAUTION: Wea r glove s t o remov e an d instal l th e sea t
cover .
NOTE :
• Tak e car e no t t o tea r th e seam s o r damag e th e
cover .
• Remov e th e powe r sea t switc h (se e pag e 20-39 ) an d
sea t bel t buckl e (se e pag e 20-43 ) fro m th e seat .
1 . Detac h th e clip s an d hook s fro m unde r th e seat .
Pul l th e sea t cove r back .
I: Cli p location s
SEA T COVE R
2. Detac h th e hook s whil e pullin g th e sea t cove r back .
SEAT COVE R
3. Detac h th e clip s fro m unde r th e seat , the n remov e
th e sea t cushion .
Clip location s
SEAT CUSHIO N
4. Remov e th e sea t bel t buckl e (se e pag e 20-43 ).
Detac h th e hook s a t bot h side s o f th e seat .
Remov e th e screw s a t bot h fron t edges .
SEAT COVE R
SCRE W
HOOKS
ADHESIV
E ARE A
HOOK S HOO
K (3 )
HOOK
ProCarManuals.com

5. Detach the clips, then pull the seat cover back.

Remove the fasteners by pulling the seat-back

cushion.

NOTE: Take care not to tear the seams or damage

the seat cover.

Clip locations

FASTENERS

SEAT-BACK

SEAT COVER
6. Detach the clips from the seat-back, then pull the

seat-back cushion up as shown. Remove the retain-

ers, then remove the headrest by pulling it up. Re-

move the fastener on the left side.

Clip locations

RETAINER

Turn the retainer as shown,

then pull it out.

NOTE: When installing the headrest, first install

the retainers to the headrest guides.
HEADREST

GUIDE

HEADREST

FASTENER

SEAT-BACK

CUSHIONProCarManuals.com