window Alfa Romeo Giulietta 2012 Owner handbook (in English)

71
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CLIMATE CONTROL SYSTEM COMPRESSOR
Press C to turn the compressor on/off (the LED on the button will
light up when the compressor is on). The system remembers that
the compressor has been switched off, even after the engine has
stopped.
When the compressor is switched off the system deactivates air re-
circulation to prevent the windows from misting up and deactivates
the AQS function. In this case, although the system is capable of
maintaining the required temperature, the AUTO LED will go out.
The temperatures will flash for a few seconds if the required tem-
perature cannot be maintained.
To restore automatic control for switching on the climate control
compressor, press C button again or press the AUTO button.
With compressor off:
❍if the outside temperature is higher than the set one, the sys-
tem will not be able to satisfy the request. The temperature
value will then flash on the display for a few seconds;
❍the fan speed can be manually reset.
When the compressor is on and the engine is running, manual ven-
tilation cannot drop under the maximum speed (only one LED on).
IMPORTANT With the climate control compressor off, it is not pos-
sible to admit air into the passenger compartment with a tempera-
ture below the outside temperature; moreover, under certain envi-
ronmental conditions the windows could mist up very quickly since
the air cannot be dehumidified.
RAPID WINDOW DEMISTING/DEFROSTING
(MAX-DEF function)
Press-to turn windscreen and side window demisting/defrosting
function on (LED on button lit). The climate control system carries
out the following operations:
❍switches on the climate control compressor when climatic con-
ditions allow;
❍turns air recirculation off;
❍sets maximum air temperature (HI) in both zones;
❍sets proper fan speed according to the engine coolant tem-
perature;
❍directs air flow to the windscreen and front side windows vents;
❍the heated rear windscreen is turned on
❍shows fan speed (LED G lit).
IMPORTANT The MAX-DEF function will remain on for approximately
3 minutes from when the engine coolant reaches adequate tem-
perature.
The LED on the AUTO button will go out when the function is on.
With the function activated the only possible manual adjustments
are adjusting the fan speed and the turning the heated rear wind-
screen off. By pressing B, C,
-or AUTO buttons, the climate
control system will turn the MAX-DEF off.

72
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
DEMISTING/DEFROSTING
HEATED REAR WINDSCREEN
Press(to turn heated rear windscreen demisting/defrosting func-
tion on (LED on button lit). This function switches off automatically
after about 20 minutes or when the engine is turned off. It is not
switched on automatically the next time the engine is started. For
versions/markets, where provided, pressing the
(button it is al-
so possible to defrost/demist the external rearview mirrors (for
versions/markets, where provided) and the heated spray nozzles
(for versions/markets, where provided).
IMPORTANT Do not affix stickers to the inside of the heated rear
windscreen on the heating filaments, to avoid damage that might
cause them to stop working properly.
Thermal comfort windscreen
(for versions/markets, where provided)
Some versions feature a thermal comfort windscreen which, with
the car exposed to the sun, limits the extent of temperature in-
crease inside the passenger compartment, thus ensuring greater
comfort.
Humidity sensor (for versions/markets, where provided)
The humidity sensor prevents the windows from misting up. For
full operation, it is advisable to turn the AUTO on (LED N on). When
the outside temperature is low, the system could automatically turn
the compressor on and turn air recirculation off for safer driving.
TURNING THE CLIMATE CONTROL SYSTEM OFF
Pressgbutton (LED on button off):
❍air recirculation is on, thus isolating the passenger compartment
from the outside;
❍the compressor is off;
❍the fan is off.
❍the heated rear windscreen can be switched on or off.
❍the AQS (Air Quality System) function cannot be turned on.
IMPORTANT The climate control system control unit stores the tem-
peratures set before the system was switched off and restores
the same conditions when any button of the system is pressed (ex-
cept for D button).
Press AUTO button to restart the climate control system in fully
automatic mode.

73
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
NOTEWhen the Start&Stop function is active (engine off and
vehicle speed zero), the automatic recirculation management is
turned off always taking air in from outside, to reduce the proba-
bility of window misting up (as the compressor is off).
SUPPLEMENTARY ELECTRIC HEATER
(for versions/markets where provided)
This device speeds up passenger compartment warming when it is
very cold. The additional heater turns off automatically after reach-
ing the required comfort conditions.
Automatic dual zone climate control system
(for versions/markets, where provided)
The supplementary electric heater is operated automatically ac-
cording to environmental conditions and when the engine is run-
ning.
Manual climate control system
The supplementary heater is activated automatically by turning A
knob to the end of the red section and setting the fan (knob B)
to at least the 1
stspeed.
IMPORTANT NOTES
The heater only works if the outside temperature and engine coolant
temperature are low.
The heater will not activate if the battery voltage is too low.
START&STOP
Automatic climate control system
The automatic climate control system manages the Start&Stop
function (engine off when speed is zero) to ensure adequate com-
fort inside the passenger compartment.
Specifically, the Start&Stop function is turned off when the weath-
er is particularly hot or cold to guarantee an adequate level of com-
fort inside the passenger compartment; therefore, the engine will
not be stopped during these transient conditions, even if the speed
is zero.
When the Start&Stop is on and the engine is off at zero speed,
the climate control system will turn the engine back on if the in-
side temperature conditions should rapidly deteriorate (or if the
user asks for maximum cooling – LO – or quick demisting –
MAX-DEF).
With the Start&Stop function on and engine off at zero speed,
air flow is reduced to the minimum to main comfort conditions in-
side the passenger compartment as long as possible when the sys-
tem is in AUTO mod (LED N on).
The climate control system attempts to manage the discomfort
caused by the engine stopping (compressor and engine coolant
pump off) but operation of the climate control system can be priv-
ileged by turning the Start&Stop off by pressing the button on
the dashboard.
NOTEIn particularly severe climate conditions it is recommen-
ded to limit the use of the Start&Stop function to prevent the com-
pressor from continuously switching on and off, with following fa-
st window misting and accumulation of humidity with unpleasant
smells in the passenger compartment.

77
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Move the stalk up (unstable position) to limit operation to the time
for which the stalk is held in this position. When released, the stalk
will return to its default position and the wiper will be automati-
cally stopped.WINDOW CLEANING
The right stalk controls windscreen wiper/washer and heated rear
windscreen wiper/washer operation.
WINDSCREEN WIPER/WASHER fig. 41
This only operates with the ignition turned to MAR. The ring nut A
can have the following positions::
Owindscreen wiper off;
≤intermittent operation (low speed);
AUTO rain sensor activation (for versions/markets, where pro-
vided) (the windscreen wiper speed is automatically adapt-
ed to the intensity of the rain)
nintermittent operation;
≥slow operation;
¥fast operation.
fig. 41A0K0097m
Do not use the windscreen wipers to remove lay-
ers of snow or ice from the windscreen. In such con-
ditions, the windscreen wipers may be subjected to
excessive stress, prompting intervention from the motor
protection which prevents operation for a few seconds. If
operation is not restored, even after turning the key and
restarting the engine, contact Alfa Romeo Authorized Ser-
vices.
Do not operate the windscreen wiper with the
blades lifted from the windscreen.
“Smart washing” function
Pull the stalk towards the steering wheel (unstable position) to op-
erate the windscreen washer jet. Keep the stalk pulled for more
than half a second, with just one movement, to operate windscreen
washer/wiper jet at the same time.
The wiper stops working three strokes after the stalk is released.
A further stroke after approximately six seconds completes the wip-
ing cycle.

79
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
CRUISE CONTROL
(for versions/markets, where provided)
GENERAL INFORMATION
This is an electronic driving aid that allows you to drive at a speed
of above 30 km/h on long and straight dry roads (e.g. motor-
ways), at a preset speed without having to press the accelerator
pedal. It is therefore not recommended to use this device on coun-
try roads with traffic. Do not use it in town.
TURNING THE DEVICE ON
Turn ring A-fig. 43 to ON. The device cannot be turned on in 1stor
reverse gear. It is advisable to engage it in 5thgear or higher.
When travelling downhill with the device engaged, the car may
slightly exceed the preset speed. When the device is activated,
Ü
light comes on together with the relevant message on the instru-
ment panel (for versions/markets, where provided).
REAR WINDOW WIPER/WASHER
(for versions/markets, where provided)
Activation
This only operates with the ignition turned to MAR.
Turn B ring fig. 41 from position
Oto position 'to turn on the
rear window wiper as follows:
❍intermittent operation if the windscreen wiper is off;
❍synchronised operation (but with half-stroke frequency) when
the windscreen wiper is on;
❍continuous operation with reverse engaged and windscreen
wiper on.
With reverse gear engaged and windscreen wiper on, the rear win-
dow wiper is activated in continuous mode. Pushing the stalk to-
wards the dashboard (temporary position) the rear window wash-
er jet will activate.
Keeping the stalk pushed for more than half a second also the rear
window wiper will activate. Releasing the stalk will activate the
smart washing function, as described for the windscreen wiper.
fig. 43A0K0098m

92
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
ELECTRIC SUN ROOF
(for versions/markets, where provided)
The sun roof comprises two glass panels; the front one is mobile
and the rear one fixed. These are equipped with two sun blinds
(front and rear) that can be moved manually. With the sun roof
closed, the blinds can be placed in any position.
OPERATION
The sunroof can be operated only with the ignition key turned to
MAR. The controls A and B-Fig. 63 on the front courtesy light trim,
operate the sun roof opening/closing functions.
Opening the sunroof
Press button A-fig. 63 and hold it pressed: the front glass panel will
assume the spoiler position. Press button A again and operate the
control for longer than half a second to move the roof window to
an intermediate position (“Comfort” position).
Press the opening control for longer than half a second to open the
roof entirely. The front panel can be stopped in an intermediate po-
sition by pressing button A again.
Closing the sunroof
With the sunroof in the fully open position, press button B-fig. 62
and, if the button is operated for more than half a second, the front
roof glass with automatically assume the intermediate position
(comfort position).
If the button is operated again for about half a second the roof
will assume the spoiler position. Lastly, if the button B is pressed
again, the roof will assume the fully closed position.
fig. 63A0K0131m

98
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
ELECTRIC WINDOWS
The window winders work with the ignition key at MAR and for
approximately three minutes after turning the key to STOP or ex-
tracting it and opening one of the front doors.
The control buttons are located in the door panels (the driver’s door
panel can be used to operate all the windows).
An anti-pinch device is operated when the front and rear windows
are wound up.
CONTROLS fig. 68
Front door driver’s side
A. opening/closing left hand front window; “continuous auto-
matic” operation during window opening/closing stage;
B. opening/closing right hand front window; “continuous auto-
matic” operation during window opening/closing stage;
C. enabling/disabling of rear door electric window controls;
D. opening/closing left hand rear window (for versions/markets,
where provided); “continuous automatic” operation during win-
dow opening/closing stage;
E. opening/closing right hand rear window (for versions/markets,
where provided); “continuous automatic” operation during win-
dow opening/closing stage;
Press the buttons to open/close the required window. When one
of the two buttons is pressed briefly, the window moves in stages;
if the button is held down, “continuous automatic” operation is ac-
tivated both for closing and opening. If the button is pressed again
the window will stop in its current position. Holding the button
pressed for a few seconds, the window automatically raises or low-
ers (only with key on MAR).
Front door passenger’s side/rear doors
(for versions/markets, where provided)
On the passenger side front door control panel, and on some ver-
sions also on the rear doors, buttons F-fig. 68 are provided to con-
trol the relevant windows
fig. 68A0K0067m

99
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
IMPORTANT With ignition key at STOP or removed, the electric win-
dows remain active for about 3 minutes and are deactivated the
moment a door is opened.
IMPORTANT On some versions when the
Ëbutton on the remote
control is pressed for longer than 2 seconds the windows will open,
whilst if the
Ábutton is pressed for longer than 2 seconds the
windows will close.
The system conforms to the 2000/4/EC standard
concerning the safety of passengers leaning out of
the passenger compartment.
Incorrect use of the electric windows may be danger-
ous. Before and during operation, always check that
no passenger is at risk of being injured directly by
the moving window or by objects getting caught in or dragged
by the window. When leaving the car, always remove the key
from the ignition device to avoid the risk of injury due to ac-
cidental operation of the electric windows. This is a danger to
the people still on board.
Anti-pinch device
The car is equipped with an anti-pinch safety device for the upwards
motion of the windows.
The windows are fitted with an anti-pinch safety system that de-
tects the presence of an obstacle when they are closing and cuts
in by stopping the window and reversing it according to the posi-
tion of the window. This device is also useful when the windows
are activated accidentally by children on board the car.
The anti-pinch function is active both during manual and automat-
ic operation of the electric windows. Following the intervention of
the anti-pinch system, the window travel is immediately interrupt-
ed and subsequently reversed until the lower end of travel is
reached. The window cannot be operated in any way during this
time.
IMPORTANT If the anti-pinch protection intervenes 5 consecutive
times within a minute or is faulty, the automatic closing operation
of the window is inhibited, only allowing it in steps of half a sec-
ond; the button is released for the subsequent manoeuvre.
Open the concerned window to restore correct operation of the sys-
tem.

100
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
Electric window system initialisation
The system must be re-initialised after disconnecting the battery
or if the relevant protection fuse is blown.
Initialisation procedure:
❍fully close the window manually to initialise;
❍after the window has reached the upper end of travel, hold the
up button pressed for at least one second.
IMPORTANT For versions/markets where provided, following the
disconnection of the power supply (replacing or disconnecting the
battery or replacing the protection fuse for the electric window con-
trol units), the automatic setting for the electric windows must be
reset.The reset operation should be carried out with the doors closed
according to the following procedure:
1. completely lower the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached (lower end stop);
2. completely raise the driver-side window and keep the button
pressed for at least 3 seconds once the end of travel position
has been reached (upper end stop);
3. repeat stages 1 and 2 also for the passenger’s window
4. check that the initialisation has taken place correctly by check-
ing the automatic operation of the windows.

148
GETTING
TO KNOW
YOUR CAR
SAFETY
STARTING
AND DRIVING
IN AN
EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
CONTENTS
SIDE AIR BAGS
(SIDE BAG - WINDOW BAG)
The car is fitted with front side bags for driver and passenger for
protecting the chest, and window bags for protecting front and rear
passengers’ heads.
Side bags protect car occupants from side crashes of medium-high
severity, by placing the cushion between the occupant and the in-
ternal parts of the side structure of the car.
Non-activation of side bags in other types of collisions (front colli-
sions, rear shunts, roll-overs, etc...) is not a system malfunction.
fig. 108A0K0081mfig. 109A0K0035m
FRONT SIDE BAGS fig. 108
These are comprised of two types of bags located in the front
back/rests, which protect the chest and pelvis area of passen-
gers in the event of a side impact of medium-high severity.
HEAD PROTECTION SIDE AIR BAGS
(WINDOW BAGS) fig. 109
It is formed by two "curtain" window bags are located behind the
side roof upholstery and are covered by special trimming.
They were designed to protect the head of front and rear passen-
gers in case of side collisions, thanks to the wide cushion inflation
surface.
The air bags are not deployed in the event of impact of low sever-
ity (for which the retaining action of the seat belts is sufficient).
It is therefore always necessary to wear seat belts.
In the event of a side impact, the system provides best protection
if the passenger sits on the seat in a correct position, thus allow-
ing correct window bag deployment.