navigation AUDI A8 2005 D3 / 2.G RNS_E Navigation System Manual

Overview13
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Tips
You can find information about the different drives starting on page 34.Anti-theft codingGeneral
Effective safety measures in conjunction with the PIN
prevent misuse of the equipment by unauthorized
parties.The electronic lock-up is operational, if:

the Navigation System is removed from the vehicle,


the Navigation System is disconnected from the vehicle current
supply,


the battery is disconnected or


the electric fuse for the Navigation System is blown.
I f t h e a n t i - t h e ft c o d i n g h as l o cke d up t h e N a v i g a t i o n S ys t e m fo r o n e
of the reasons given, the speller display for entering the PIN
page 14, fig.6 appears after the Navigation System is switched
on.
After that, the Navigation System can only be operated again only
by entering the correct PIN.
This PIN is attached to the equipment card along with the equip-
ment number.
The PIN can be used for your equipment alone and cannot be
changed.
Note
The “equipment card” should be removed and kept in a safe place -
under no circumstances should it be kept in the vehicle. This makes
the Audi Navigation System unusable by thieves.Applies to vehicles: with convenience codingUser-friendly radio codingAft e r t he P I N i s e n t e re d t h e fir s t t im e , t h e N a v i g a t i o n S ys t e m g e t s to
know its vehicle.
If the power supply was interrupted, the Navigation System checks
to see whether it is still its vehicle. If it is, the Navigation System is
ready for use again after a few seconds.
It is no longer necessary to manually disable the electronic lock!
However, if the Navigation System is installed in another vehicle,
the electronic lock must be cancelled by entering the PIN page 14.

Overview 14Entering PINFig. 6 Speller display: Entering PIN– Switch the ignition on.
– Switch the Navigation System on if it is not switched on
automatically
page 11.
– Enter the PIN using the speller
fig.6.
– Confirm your entry with OK. The electronic lock is
cancelled.Yo u h a v e two attempts to enter the correct PIN. The number of
attempts is shown in the display. If you enter the incorrect PIN twice
in succession, the message System is locked appears in the display.Unlocking the system (unlocking procedure)
Before you can enter the PIN again, the electronic lock must be
cancelled. This happens automatically w h e n t h e N a v i g a t i o n S y s t e m
has been switched on for about 60 minutes. If you do not insert the
ignition key into the lock, the Navigation System switches off auto-
matically after 30 minutes. When the Navigation System switches
off automatically or is switched off, the unlocking process is
cancelled and has to be started over.
When the unlocking process is complete, you have two more
attempts to enter the correct PIN. If you enter the incorrect PIN
again twice in succession, the procedure must be repeated.
Tips
If you lose your PIN, contact an Audi dealership or authorized
facility.

General system operation15
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
General system operationControlsBasic operating functions
A l l t h e f u n c t i o n s o f t h e N a v i g a t i o n S y s t e m c a n b e o p e r -
ated with four basic rules.Fig. 7 Navigation System ControlsThe buttons on the operating unit have been assigned the
following four basic functions:
1. Press one of the function keys
fig.7 (
page 16) to
reach the desired main function (e.g. radio operation,
navigation).2. Rotate and press the control knob
fig.7
(
page 17) to make a selection in the Display.
3. Press one of the control buttons
fig.7 (
page 17)
to o p e n o n e o f t h e s ub m en u s i n t h e p a r t i c ul ar m a i n fu n c -
tion. You can find the current submenus in the four
corners of the display. The four corners of the display
correspond to the four control buttons that are posi-
tioned around the control knob.
4. Press the button
fig.7 (
page 18) to
cancel a selection not yet confirmed or to return to the
next higher level.
In principle you only need to take note of the buttons described,
along with their main functions. You will be led through the oper-
ating procedures with the help of the menus, which are mostly self-
explanatory.
A1
A2
A
RETURN
A4

General system operation 16Function buttons
The function buttons determine which main functions
are shown in the display.Fig. 8 Navigation System: Function buttons– P r e s s a f u n c t i o n b u t t o n
f i g .8 t o r e a c h t h e d e s i r e d m a i n
function.If the Navigation System is switched on, all main functions are
active.
The main menu or a submenu assigned to this main function is
s h o w n i n t h e d i s p l a y
page 20, “History function”. When you press
the function button again, you usually go the particular main menu
page 20, “Home function”.
If you pressed the button in one of the main functions, you
can leave that Setup menu by pressing the button
again
page 169. The Setup function works in conjunction with an already activated function button. This opens special settings
belonging to the main function just selected.
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button

Running the CD drives . . . . . . . . . . . . . . . . . . . . . . . . .
Running the MP3 player . . . . . . . . . . . . . . . . . . . . . . . .
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button
1)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SETUP
SETUP
1)Telephone is not installed.A1
FM

AM
56
A2
CD/SD
78
83
A3
NAME
98
A4
TEL
105
A5
NAV
108
A6
INFO
163
A7
CAR
168
A8
SETUP
169

General system operation17
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Control knob
Yo u c a n m a k e a s e l e c t i o n i n t h e D i s p l a y b y t u r n i n g a n d
pressing the control knob.Rotation function
– Rotate the control knob
fig.9 to select a menu item in
the Display.
– Rotate the control knob clockwise or counter-clockwise
to move the cursor up or down.
Pressing function
– Press the control knob
fig.9 to confirm the selection
or entry.If an arrow
page 29, fig.23 is visible in the lower or upper
Display corner, additional menu items can be called up by
continuing to rotate the knob
page 29.
Control buttons
The control buttons are logically assigned to the
corners of the screen.
Fig. 9 Navigation
System: Control knob
A
-8 ;
%-
)2
 $
/,-8 ;; %-
)2
 -
 
. /, 
/, 2/  

.

 .
8

General system operation 18Th e fo ur control buttons organized around the control
knob
page 17, fig.10 are arranged to correspond to the bar-
shaped switch symbols in the screen corners: the top right screen
corner corresponds to the top right control button
page 17,
fig.11.
When you press a control button, a new menu group is displayed
which is assigned thematically to the particular main function.
To make orientation easier, the activated control button is illumi-
nated and the corresponding corner of the screen is highlighted in
color.
Return buttonB y p r e s s i n g t h e b u t t o n y o u w i l l j u m p b a c k o n e l e v e l i n t h e
menu hierarchy within a main function.
A selection that has not been confirmed by pressing the control
knob will be cancelled.The button is available in every menu application.
Using the button, you can also deactivate the active side
menu in the navigation map display
page 144.
Tips
If you activate the function button
page 16 within a main func-
tion, the system will automatically jump to the main menu of that
main function. Please note
page 20, “Home function”.
Forward/Reverse buttonDepending on the operating mode, the following functions are
carried out with these buttons:
Main radio function is active
go to next station on the radio station list
go to previous station on the radio station list
Fig. 12 Navigation
System: Return button
RETURN
RETURN
RETURN
Fig. 13 Navigation
System
Forward/reverse
button

|A2
|A1

General system operation19
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP If you would like to scroll in an active radio station list using the
Forward/Reverse button, it is not necessary to show the station list
in the Navigation System display.
If the radio memory list
page 61 is shown in the Navigation
System display, you can select a a station from the memory list by
pressing the Forward/Reverse button.
Main CD function is active
Pressing the button calls up the next CD track. If the button is
held down, fast forward is activated.
You can jump back to the previous track by pressing the button
within the first 10 seconds of play time for a track. After 10
s e c o n d s i t j um p s t o t h e s t a r t o f t h e t ra ck. I f t h e b ut to n is he l d d o w n ,
reverse is activated.
If you would like to scroll in an active CD track list using the
Forward/Reverse button or activate forward/reverse it is not neces-
sary to show the CD operating menu in the Navigation System
display.
Main MP3 function is active
Pressing the button c alls up the n e xt in the MP3 p layer. If the
button is held down, fast forward is activated.
You can jump back to the previous track by pressing the button
within the first 10 seconds of play time for a track. After 10
s e c o n d s i t j um p s t o t h e s t a r t o f t h e t ra ck. I f t h e b ut to n is he l d d o w n ,
reverse is activated.
If you would like to scroll in an active MP3 track list using the
Forward/Reverse button or activate forward/reverse it is not neces-
sary to show the MP3 operating menu in the Navigation System
display.
Adjusting volumeVolume can be adjusted by turning the ON/OFF button. The volume
setting will be stored automatically.
If the volume is too high when the radio is turned on, it will be
reduced automatically to a level set by the factory. If the volume is
too low when the radio is turned on, it will be increased automati-
cally to a level set by the factory.
Tips
Volume can also be adjusted using the buttons on the multi-func-
tion steering wheel*
page 21.

|
A2
|
A1

|
A2
|
A1
Fig. 14 Navigation
System ON/OFF knob -
adjusting volume

General system operation 20Home functionIf you activate the function button within a main function, the
system will automatically jump to the main menu of that main func-
tion.
In Navigation “Home function” depends on the route guidance
selected: If you have activated route guidance with stopovers, you
go to the menu for route planning by pressing the function button
again
page 139, fig.146. If you have activated route guidance
without stopovers
page 139, y o u g o t o t h e m a i n n a v i g a t i o n m e n u
(singe destination mode) by pressing the function button again.
History function
The system recalls the previous settings.When a function button is pressed, the system will switch to the
most recently accessed menu level for the specific main function.
This includes any sublevels that were opened. This excludes Setup
menus.
The history memory is erased when the system moves into standby
mode.
An example: You are currently on the Tuning radio menu and switch
to the navigation menu by pushing the button. If you press
the button at this time, you will not jump to the main radio
menu, but directly to the Tuning radio menu.
Start Navigation System ResetThe following process will restart your Audi Navigation
System and will allow complete functionality sytem to be
restored.
– Press the ON/OFF knob to switch the Navigation System
off.
– Press and hold the ON/OFF knob until the display reap-
pears and turns black.
– Release the ON/OFF knob as soon as the display has
turned black. A f t e r a f e w s e c o n d s , t h e N a v i g a t i o n S y s t e m
begins its restart, or you can switch it on manually

page 11.
NAV
FM

AM
Fig. 15 Navigation
System ON/OFF knob

General system operation21
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Multi-function steering wheelApplies to vehicles: with multi-function steering wheelGeneral
The multi-function steering wheel enables quick and
easy operation of selected systems on the Navigation
System.To minimize driver distraction when operating the Navigation
System and its components, buttons for controlling basic audio
functions are placed on the multi-function steering wheel. However,
this applies only if your vehicle equipment was installed at the
factory.
Depending on the multi-function steering wheel in your vehicle, you
can use audio functions.
You use the buttons to operate the function that is active at the time.
For example, if you are listening to the radio, you can select the
last/next station from the station list using the or button on
the multi-function steering wheel with audio controls*.
The volume can be adjusted in each active function.
Of course, you can continue to use the audio functions from the
Navigation System.
Tips
If systems have not been installed in the vehicle, the button on the
multi-function steering wheel* assigned to that system is
inoperative.
Applies to vehicles: with multi-function steering wheel with audio operationMulti-function steering wheel with audio operationYou can perform the following functions with this
multi-function steering wheel:



Button
Function
description
Operating
mode
Application
Press the
button
Radio
Select the previous
station on the radio
station list
a).
CD or MP3
Select the previous
track for the audio
source you are listen-
ing to.
Pres s and h old
the button
CD or MP3
Reverse
Fig. 16 Multi-function
steering wheel with
audio operation
AA


AA

General system operation 22
Applies to vehicles: with multi-function steering wheel with audio operation - version AMulti-function steering wheel with audio operation - version A
Press the
button
Radio
Select the next station
on the radio station
list
a).
CD or MP3
Select the next track
for the audio source
you are listening to.
Pres s an d h old
the button
CD or MP3
Fast forward
Press the
button
Radio, CD or
MP3
Increase volume
Press the
button
Radio, CD or
MP3
Reduce volume
Press the
button
Radio
Frequency scan
CD
Load the previous CD
if CD changer* is
installed
MP3
Switch to previous
available MP3 drive
Press the
button
Radio
Frequency scan
CD
Load the ne xt CD if CD
changer* is installed
MP3
Switch to next avail-
able MP3 drive
a)If the radio memory list is shown in the Navigation System display, a radio
station can be selected from the list using the left menu thumbwheel.Button
Function
description
Operating
mode
Application
AB

AB

AC

AD

AE

AF

Fig. 17 Multi-function
steering wheel with
audio operation
(version A)